asterisk-config 1:11.13.1~dfsg-2+deb8u5 / etc / asterisk / codecs.conf

This file is indexed.

/etc/asterisk/codecs.conf is in asterisk-config 1:11.13.1~dfsg-2+deb8u5.

This file is owned by root:root, with mode 0o640.

The actual contents of the file can be viewed below. 

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
[speex]
; CBR encoding quality [0..10]
; used only when vbr = false
quality => 3

; codec complexity [0..10]
; tradeoff between cpu/quality
complexity => 2

; perceptual enhancement [true / false]
; improves clarity of decoded speech
enhancement => true

; voice activity detection [true / false]
; reduces bitrate when no voice detected, used only for CBR
; (implicit in VBR/ABR)
vad => true

; variable bit rate [true / false]
; uses bit rate proportionate to voice complexity
vbr => true

; available bit rate [bps, 0 = off]
; encoding quality modulated to match this target bit rate
; not recommended with dtx or pp_vad - may cause bandwidth spikes
abr => 0

; VBR encoding quality [0-10]
; floating-point values allowed
vbr_quality => 4

; discontinuous transmission [true / false]
; stops transmitting completely when silence is detected
; pp_vad is far more effective but more CPU intensive
dtx => false

; preprocessor configuration
; these options only affect Speex v1.1.8 or newer

; enable preprocessor [true / false]
; allows dsp functionality below but incurs CPU overhead
preprocess => false

; preproc voice activity detection [true / false]
; more advanced equivalent of DTX, based on voice frequencies
pp_vad => false

; preproc automatic gain control [true / false]
pp_agc => false
pp_agc_level => 8000

; preproc denoiser [true / false]
pp_denoise => false

; preproc dereverb [true / false]
pp_dereverb => false
pp_dereverb_decay => 0.4
pp_dereverb_level => 0.3


[plc]
; for all codecs which do not support native PLC
; this determines whether to perform generic PLC
; there is a minor performance penalty for this
genericplc => true

; Generate custom formats for formats requiring attributes.
; After defining the custom format, the name used in defining
; the format can be used throughout Asterisk in the format 'allow'
; and 'disallow' options.
;
; Example: silk8 is a predefined custom format in this config file.
; Once this config file is loaded, silk8 can be used anywhere a
; peer's codec capabilities are defined.
;
; In sip.conf 'silk8' can be defined as a capability for a peer.
; [peer1]
; type=peer
; host=dynamic
; disallow=all
; allow=silk8 ;custom codec defined in codecs.conf
;
; LIMITATIONS
; Custom formats can only be defined at startup.  Any changes to this
; file made after startup will not take into effect until after Asterisk
; is restarted.
;

; Default Custom SILK format definitions, only one custom SILK format per
; sample rate is allowed.
[silk8]
type=silk
samprate=8000
fec=true           ; turn on or off encoding with forward error correction.
                   ; On recommended, off by default.
packetloss_percentage=10   ; Estimated packet loss percentage in uplink direction.  This
                           ; affects how much redundancy is built in when using fec.
                           ; The higher the percentage, the larger amount of bandwidth is
                           ; used. Default is 0%, 10% is recommended when fec is in use.

maxbitrate=10000    ; Use the table below to make sure a useful bitrate is choosen
                    ; for maxbitrate.  If not set or value is not within the bounds
                    ; of the encoder, a default value is chosen.
                    ;
                    ;  sample rate | bitrate range
                    ;  8khz        | 5000 - 20000 bps
                    ;  12khz       | 7000 - 25000 bps
                    ;  16khz       | 8000 - 30000 bps
                    ;  24khz       | 20000- 40000 bps
                    ;
;dtx=true       ; Encode using discontinuous transmission mode or not. Turning this
                ; on will save bandwidth during periods of silence at the cost of
                ; increased computational complexity.  Off by default.

[silk12]
type=silk
samprate=12000
maxbitrate=12000
fec=true
packetloss_percentage=10;

[silk16]
type=silk
samprate=16000
maxbitrate=20000
fec=true
packetloss_percentage=10;

[silk24]
type=silk
samprate=24000
maxbitrate=30000
fec=true
packetloss_percentage=10;


; Default custom CELT codec definitions. Only one custom CELT definition is allowed
; per a sample rate.
;[celt44]
;type=celt
;samprate=44100  ; The samplerate in hz. This option is required.
;framesize=480   ; The framesize option represents the duration of each frame in samples.
                 ; This must be a factor of 2.  This option is only advertised in an SDP
                 ; when it is set.  Otherwise a default of framesize of 480 is assumed
                 ; internally

;[celt48]
;type=celt
;samprate=48000

;[celt32]
;type=celt
;samprate=32000

APT Browse - Built by Thomas Orozco.