/etc/asterisk/console.conf is in asterisk-config 1:11.13.1~dfsg-2+deb8u5.
This file is owned by root:root, with mode 0o640.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 | ;
; Configuration for chan_console, a cross-platform console channel driver.
;
[general]
; Set this option to "yes" to enable automatically answering calls on the
; console. This is very useful if the console is used as an intercom.
; The default value is "no".
;
;autoanswer = no
; Set the default context to use for outgoing calls. This can be overridden by
; dialing some extension@context, unless the overridecontext option is enabled.
; The default is "default".
;
;context = default
; Set the default extension to use for outgoing calls. The default is "s".
;
;extension = s
; Set the default CallerID for created channels.
;
;callerid = MyName Here <(256) 428-6000>
; Set the default language for created channels.
;
;language = en
; If you set overridecontext to 'yes', then the whole dial string
; will be interpreted as an extension, which is extremely useful
; to dial SIP, IAX and other extensions which use the '@' character.
; The default is "no".
;
;overridecontext = no ; if 'no', the last @ will start the context
; if 'yes' the whole string is an extension.
; Default Music on Hold class to use when this channel is placed on hold in
; the case that the music class is not set on the channel with
; Set(CHANNEL(musicclass)=whatever) in the dialplan and the peer channel
; putting this one on hold did not suggest a class to use.
;
;mohinterpret=default
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of an
; Console channel. Defaults to "no". An enabled jitterbuffer will
; be used only if the sending side can create and the receiving
; side can not accept jitter. The Console channel can't accept jitter,
; thus an enabled jitterbuffer on the receive Console side will always
; be used if the sending side can create jitter.
; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
; resynchronized. Useful to improve the quality of the voice, with
; big jumps in/broken timestamps, usually sent from exotic devices
; and programs. Defaults to 1000.
; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a Console
; channel. Two implementations are currently available - "fixed"
; (with size always equals to jbmax-size) and "adaptive" (with
; variable size, actually the new jb of IAX2). Defaults to fixed.
; jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
; The option represents the number of milliseconds by which the new
; jitter buffer will pad its size. the default is 40, so without
; modification, the new jitter buffer will set its size to the jitter
; value plus 40 milliseconds. increasing this value may help if your
; network normally has low jitter, but occasionally has spikes.
; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------
;
; Any configuration context defined beyond the [general] section configures
; specific devices for use.
;
[default]
input_device = default ; When configuring an input device and output device,
output_device = default ; use the name that you see when you run the "console
; list available" CLI command. If you say "default", the
; system default input and output devices will be used.
autoanswer = no
context = default
extension = s
callerid = MyName Here <(256) 428-6000>
language = en
overridecontext = no
mohinterpret = default
active = yes ; This option should only be set for one console.
; It means that it is the active console to be
; used from the Asterisk CLI.
|