/etc/asterisk/sla.conf is in asterisk-config 1:11.13.1~dfsg-2+deb8u5.
This file is owned by root:root, with mode 0o640.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 | ;
; Configuration for Shared Line Appearances (SLA).
;
; See http://wiki.asterisk.org or doc/AST.pdf for more information.
;
; ---- General Options ----------------
[general]
;attemptcallerid=no ; Attempt CallerID handling. The default value for this
; is "no" because CallerID handling with an SLA setup is
; known to not work properly in some situations. However,
; feel free to enable it if you would like. If you do, and
; you find problems, please do not report them.
; -------------------------------------
; ********************************
; **** Configuration Ordering ****
; ********************************
; Note that SLA configuration processing assumes that *all* trunk declarations are
; listed in the configuration file before any stations.
; ********************************
; ********************************
; ---- Trunk Declarations -------------
;
;[line1] ; Provide a name for this trunk.
;type=trunk ; This line is what marks this entry as a trunk.
;device=DAHDI/3 ; Map this trunk declaration to a specific device.
; NOTE: You can not just put any type of channel here.
; DAHDI channels can be directly used. IP trunks
; require some indirect configuration which is
; described in
; https://wiki.asterisk.org/wiki/display/AST/SLA+Trunk+Configuration
;autocontext=line1 ; This supports automatic generation of the dialplan entries
; if the autocontext option is used. Each trunk should have
; a unique context name. Then, in chan_dahdi.conf, this device
; should be configured to have incoming calls go to this context.
;ringtimeout=30 ; Set how long to allow this trunk to ring on an inbound call before hanging
; it up as an unanswered call. The value is in seconds.
;barge=no ; If this option is set to "no", then no station will be
; allowed to join a call that is in progress. The default
; value is "yes".
;hold=private ; This option configure hold permissions for this trunk.
; "open" - This means that any station can put this trunk
; on hold, and any station can retrieve it from
; hold. This is the default.
; "private" - This means that once a station puts the
; trunk on hold, no other station will be
; allowed to retrieve the call from hold.
;[line2]
;type=trunk
;device=DAHDI/4
;autocontext=line2
;[line3]
;type=trunk
;device=DAHDI/3
;autocontext=line3
;[line4]
;type=trunk
;device=Local/disa@line4_outbound ; A Local channel in combination with the Disa
; application can be used to support IP trunks.
; See https://wiki.asterisk.org/wiki/display/AST/SLA+Trunk+Configuration
;autocontext=line4
; --------------------------------------
; ---- Station Declarations ------------
;[station1] ; Define a name for this station.
;type=station ; This line indicates that this entry is a station.
;device=SIP/station1 ; Each station must be mapped to a device.
;autocontext=sla_stations ; This supports automatic generation of the dialplan entries if
; the autocontext option is used. All stations can use the same
; context without conflict. The device for this station should
; have its context configured to the same one listed here.
;ringtimeout=10 ; Set a timeout for how long to allow the station to ring for an
; incoming call, in seconds.
;ringdelay=10 ; Set a time for how long to wait before beginning to ring this station
; once there is an incoming call, in seconds.
;hold=private ; This option configure hold permissions for this station. Note
; that if private hold is set in the trunk entry, that will override
; anything here. However, if a trunk has open hold access, but this
; station is set to private hold, then the private hold will be in
; effect.
; "open" - This means that once this station puts a call
; on hold, any other station is allowed to retrieve
; it. This is the default.
; "private" - This means that once this station puts a
; call on hold, no other station will be
; allowed to retrieve the call from hold.
;trunk=line1 ; Individually list all of the trunks that will appear on this station. This
; order is significant. It should be the same order as they appear on the
; phone. The order here defines the order of preference that the trunks will
; be used.
;trunk=line2
;trunk=line3,ringdelay=5 ; A ring delay for the station can also be specified for a specific trunk.
; If a ring delay is specified both for the whole station and for a specific
; trunk on a station, the setting for the specific trunk will take priority.
; This value is in seconds.
;trunk=line4,ringtimeout=5 ; A ring timeout for the station can also be specified for a specific trunk.
; If a ring timeout is specified both for the whole station and for a specific
; trunk on a station, the setting for the specific trunk will take priority.
; This value is in seconds.
;[station](!) ; When there are a lot of stations that are configured the same way,
; it is convenient to use a configuration template like this so that
; the common settings stay in one place.
;type=station
;autocontext=sla_stations
;trunk=line1
;trunk=line2
;trunk=line3
;trunk=line4
;[station2](station) ; Define a station that uses the configuration from the template "station".
;device=SIP/station2
;
;[station3](station)
;device=SIP/station3
;
;[station4](station)
;device=SIP/station4
;
;[station5](station)
;device=SIP/station5
; --------------------------------------
|