This file is indexed.

/usr/bin/dh_auto_install is in debhelper 9.20150101+deb8u2.

This file is owned by root:root, with mode 0o755.

The actual contents of the file can be viewed below.

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
#!/usr/bin/perl -w

=head1 NAME

dh_auto_install - automatically runs make install or similar

=cut

use strict;
use Debian::Debhelper::Dh_Lib;
use Debian::Debhelper::Dh_Buildsystems;
use File::Spec;
use Cwd;

=head1 SYNOPSIS

B<dh_auto_install> [S<I<build system options>>] [S<I<debhelper options>>] [S<B<--> I<params>>]

=head1 DESCRIPTION

B<dh_auto_install> is a debhelper program that tries to automatically install
built files. It does so by running the appropriate command for the build
system it detects the package uses. For example, if there's a F<Makefile> and
it contains a B<install> target, then this is done by running B<make> (or B<MAKE>,
if the environment variable is set). If there is a F<setup.py> or F<Build.PL>,
it is used. Note that the Ant build system does not support installation,
so B<dh_auto_install> will not install files built using Ant.

Unless B<--destdir> option is specified, the files are installed into
debian/I<package>/ if there is only one binary package. In the multiple binary
package case, the files are instead installed into F<debian/tmp/>, and should be
moved from there to the appropriate package build directory using
L<dh_install(1)>.

B<DESTDIR> is used to tell make where to install the files. 
If the Makefile was generated by MakeMaker from a F<Makefile.PL>, it will
automatically set B<PREFIX=/usr> too, since such Makefiles need that.

This is intended to work for about 90% of packages. If it doesn't work, or
tries to use the wrong install target, you're encouraged to skip using
B<dh_auto_install> at all, and just run make install manually.

=head1 OPTIONS

See L<debhelper(7)/B<BUILD SYSTEM OPTIONS>> for a list of common build
system selection and control options.

=over 4

=item B<--destdir=>I<directory>

Install files into the specified I<directory>. If this option is not specified,
destination directory is determined automatically as described in the
L</B<DESCRIPTION>> section.

=item B<--> I<params>

Pass I<params> to the program that is run, after the parameters that
B<dh_auto_install> usually passes.

=back

=cut

my $destdir;

buildsystems_init(options => {
	"destdir=s" => \$destdir,
});

# If destdir is not specified, determine it automatically
if (!$destdir) {
	my @allpackages=getpackages();
	if (@allpackages > 1) {
		$destdir="debian/tmp";
	}
	else {
		$destdir=tmpdir($dh{MAINPACKAGE});
	}
}
$destdir = File::Spec->rel2abs($destdir, cwd());

foreach my $package (@{$dh{DOPACKAGES}}) {
	my $tmp=tmpdir($package);
	if (! -e $tmp) {
		doit("install","-d",$tmp);
	}
}

buildsystems_do("install", $destdir);

=head1 SEE ALSO

L<debhelper(7)>

This program is a part of debhelper.

=head1 AUTHOR

Joey Hess <joeyh@debian.org>

=cut