/usr/share/doc/libatm1/README.tc is in atm-tools 1:2.5.1-2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 | Basic configuration
-------------------
1. When configuring the kernel, select at least the following options under
"Networking options":
- kernel/User netlink socket
- QoS and/or fair queueing
- ATM pseudoscheduler
- Packet classifier API
- Routing tables based classifier
You may select additional schedulers/classifiers/etc. As usual, module
support is not tested yet, so you should select "y", not "m".
2. Build the kernel.
3. Download iproute2-x.x.x-now-ssXXXXXX.tar.gz from
ftp://ftp.inr.ac.ru/ip-routing/ or one of its mirrors.
4. Extract iproute2:
- tar xvfz iproute2-x.x.x-now-ssXXXXXX.tar.gz
5. Build and install iproute2:
- cd iproute2
- edit Config to enable the ATM queuing discipline: TC_CONFIG_ATM=y
- make
- cp tc/tc ip/ip /sbin
6. Run a little example. We first set up the ATM queuing discipline to
intercept selected traffic through our Ethernet interface "eth0" and
to forward this traffic over a PVC 0.100:
# tc qdisc add dev eth0 handle 1: root atm
# tc class add dev eth0 classid 1:1 atm pvc 0.100
Verify that the operation succeeded:
% tc qdisc show dev eth0
qdisc atm 1:
% tc class show dev eth0
class atm 1: parent 1: hdr . excess clp
class atm 1:1 parent 1: pvc 0.0.100 hdr aa.aa.03.00.00.00.08.00 excess clp
CONNECTED
(The first class is used to send all traffic that isn't explicitly
selected for ATM over the normal Ethernet interface. This class is
automatically created when setting up the ATM queuing discipline.)
Next, we add a filter and set up a route that selects it. If you
have enabled other filters, you can also try to select flows via
firewall rules, etc.
# tc filter add dev eth0 protocol ip route to 1 flowid 1:1
# ip route add 10.0.0.0/8 dev eth0 realm 1
Test the redirection to ATM:
% ping 10.0.0.1
Remove the ATM queuing discipline again:
# tc qdisc del dev eth0 root
Verify that the PVC has been removed:
% cat /proc/net/atm/pvc
Policing (UNTESTED !)
--------
When adding policing, proceed as follows:
1. Enable in "Networking options" the item "Ingres traffic policing"
2. Specify policy along with the classifier (use u32 or rsvp)
3. Decide on policing action. There are three choices:
- drop packet
- send packet in different class (re-classify)
- send packet in same class, with CLP=1
Note that policing is only done once, so it's not possible to
re-classify a second time. Also note that dropping currently isn't
supported by tc.
4. Set up the classifier and the class according to the choice made:
Action Classifier/filter action Class
---------- ------------------------ --------------
drop drop (not yet supported) n/a
reclassify reclassify (default) excess CLASSID
CLP=1 reclassify (default) excess clp
Example:
# tc filter add dev eth0 parent 1:1 protocol ip route \
burst 100 rate 100
# tc class add dev eth0 classid 1:1 atm pvc 0.100 excess 1:0
|