/usr/bin/radtest is in freeradius-utils 3.0.12+dfsg-5+deb9u1.
This file is owned by root:root, with mode 0o755.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 | #! /bin/sh
#
# radtest Emulate the user interface of the old
# radtest that used to be part of FreeRADIUS.
#
# Version: $Id: 7f009ae6845928c4bdef82f261249f805736e06f $
#
prefix="/usr"
exec_prefix="/usr"
bindir="${exec_prefix}/bin"
usage() {
echo "Usage: radtest [OPTIONS] user passwd radius-server[:port] nas-port-number secret [ppphint] [nasname]" >&2
echo " -d RADIUS_DIR Set radius directory" >&2
echo " -t <type> Set authentication method" >&2
echo " type can be pap, chap, mschap, or eap-md5" >&2
echo " -P protocol Select udp (default) or tcp" >&2
echo " -x Enable debug output" >&2
echo " -4 Use IPv4 for the NAS address (default)" >&2
echo " -6 Use IPv6 for the NAS address" >&2
exit 1
}
radclient=$bindir/radclient
if [ ! -x "$radclient" ] && [ -x ./radclient ]
then
radclient=./radclient
fi
# radeapclient is used for EAP-MD5.
radeapclient=$bindir/radeapclient
OPTIONS=
PASSWORD="User-Password"
NAS_ADDR_ATTR="NAS-IP-Address"
# We need at LEAST these many options
if [ $# -lt 5 ]
then
usage
fi
# Parse new command-line options
while [ `echo "$1" | cut -c 1` = "-" ]
do
case "$1" in
-4)
OPTIONS="$OPTIONS -4"
NAS_ADDR_ATTR="NAS-IP-Address"
shift
;;
-6)
OPTIONS="$OPTIONS -6"
NAS_ADDR_ATTR="NAS-IPv6-Address"
shift
;;
-d)
OPTIONS="$OPTIONS -d $2"
shift;shift
;;
-P)
OPTIONS="$OPTIONS -P $2"
shift;shift
;;
-x)
OPTIONS="$OPTIONS -x"
shift
;;
-t)
shift;
case "$1" in
pap)
PASSWORD="User-Password"
;;
chap)
PASSWORD="CHAP-Password"
;;
mschap)
PASSWORD="MS-CHAP-Password"
;;
eap-md5)
PASSWORD="User-Password"
if [ ! -x "$radeapclient" ]
then
echo "radtest: No 'radeapclient' program was found. Cannot perform EAP-MD5." >&1
exit 1
fi
radclient="$radeapclient"
;;
*)
usage
;;
esac
shift
;;
*)
usage
;;
esac
done
# Check that there are enough options left over.
if [ $# -lt 5 ] || [ $# -gt 7 ]
then
usage
fi
if [ "$7" ]
then
nas=$7
else
nas=`hostname`
fi
(
echo "User-Name = \"$1\""
echo "$PASSWORD = \"$2\""
echo "$NAS_ADDR_ATTR = $nas"
echo "NAS-Port = $4"
echo "Message-Authenticator = 0x00"
if [ "$radclient" = "$radeapclient" ]
then
echo "EAP-Code = Response"
echo "EAP-Type-Identity = \"$1\""
fi
if [ "$6" != "" -a "$6" != "0" ]
then
echo "Framed-Protocol = PPP"
fi
) | $radclient $OPTIONS -x $3 auth "$5"
exit $?
|