/usr/bin/dh_auto_install is in debhelper 9.20120909.
This file is owned by root:root, with mode 0o755.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 | #!/usr/bin/perl -w
=head1 NAME
dh_auto_install - automatically runs make install or similar
=cut
use strict;
use Debian::Debhelper::Dh_Lib;
use Debian::Debhelper::Dh_Buildsystems;
use File::Spec;
use Cwd;
=head1 SYNOPSIS
B<dh_auto_install> [S<I<build system options>>] [S<I<debhelper options>>] [S<B<--> I<params>>]
=head1 DESCRIPTION
B<dh_auto_install> is a debhelper program that tries to automatically install
built files. It does so by running the appropriate command for the build
system it detects the package uses. For example, if there's a F<Makefile> and
it contains a B<install> target, then this is done by running B<make> (or B<MAKE>,
if the environment variable is set). If there is a F<setup.py> or F<Build.PL>,
it is used. Note that the Ant build system does not support installation,
so B<dh_auto_install> will not install files built using Ant.
Unless B<--destdir> option is specified, the files are installed into
debian/I<package>/ if there is only one binary package. In the multiple binary
package case, the files are instead installed into F<debian/tmp/>, and should be
moved from there to the appropriate package build directory using
L<dh_install(1)>.
B<DESTDIR> is used to tell make where to install the files.
If the Makefile was generated by MakeMaker from a F<Makefile.PL>, it will
automatically set B<PREFIX=/usr> too, since such Makefiles need that.
This is intended to work for about 90% of packages. If it doesn't work, or
tries to use the wrong install target, you're encouraged to skip using
B<dh_auto_install> at all, and just run make install manually.
=head1 OPTIONS
See L<debhelper(7)/B<BUILD SYSTEM OPTIONS>> for a list of common build
system selection and control options.
=over 4
=item B<--destdir=>I<directory>
Install files into the specified I<directory>. If this option is not specified,
destination directory is determined automatically as described in the
L</B<DESCRIPTION>> section.
=item B<--> I<params>
Pass I<params> to the program that is run, after the parameters that
B<dh_auto_install> usually passes.
=back
=cut
my $destdir;
buildsystems_init(options => {
"destdir=s" => \$destdir,
});
# If destdir is not specified, determine it automatically
if (!$destdir) {
my @allpackages=getpackages();
if (@allpackages > 1) {
$destdir="debian/tmp";
}
else {
$destdir=tmpdir($dh{MAINPACKAGE});
}
}
$destdir = File::Spec->rel2abs($destdir, cwd());
buildsystems_do("install", $destdir);
=head1 SEE ALSO
L<debhelper(7)>
This program is a part of debhelper.
=head1 AUTHOR
Joey Hess <joeyh@debian.org>
=cut
|