/var/spool/hylafax/config/att-dataport-2 is in hylafax-server 3:6.0.6-5.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 | # $Id$
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for using the Class 2 command interface with
# an AT&T DataPort 14.4 modem. Firmware version 166 (ati1)
# or newer.
#
# Hardware flow control is used by default.
#
# CONFIG: CLASS2: AT?T*Paradyne*-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 2 interface
ModemRate: 19200 # set rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemHardFlowCmd: AT&R0\D1\Q3 # use RTS/CTS and enable RS232 handling
ModemSoftFlowCmd: AT&R1\D0\Q1 # use RTS/CTS and enable RS232 handling
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
#
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# The modem returns "OK" when there is a timeout before carrier is
# established. This is treated as "NO CARRIER" by faxd. Thus we
# need to up the NoCarrierRetrys parameter to avoid having the server
# reject jobs prematurely.
#
NoCarrierRetrys: 3 # retry 3 times on no carrier
#
# Rev C01.66.10 firmware gives a bogus result string for
# +FDCC=? query so we override it here. Syntax is:
#
# (vr),(br),(wd),(ln),(df),(ec),(bf),(st)
# where,
# vr vertical resolution
# br bit rate
# wd page width
# ln page length
# df data compression
# ec error correction
# bf binary file transfer
# st scan time/line
#
# Note that if your modem does not support V.17 then you'll need
# to restrict the values of br to (0-3) intead of (0-5).
#
Class2DCCQueryCmd: "!(0,1),(0-5),(0-4),(0-2),(0),(0),(0),(0-7)"
#
# There's no suport for HDLC frame tracing; silence the avoid
# error message so naive folks don't ask if it's a problem.
#
Class2BugCmd: AT+FBUG=0
#
# Enable copy quality checking with some "average" parameters:
#
# +FBADMUL=20 <20% bad lines for OK quality
# +FBADLIN=10 no more than 10 consecutive bad line on a page
#
# Note that default values set by the rev 1.76 firmware are 20 and 0.
#
Class2CQCmd: AT+FCQ=1;+FBADMUL=20;+FBADLIN=10
#
PagerSetupCmds: ATS41=10%B300 # use V.21 at 300 bps
|