/var/spool/hylafax/config/dsi-scout+ is in hylafax-server 3:6.0.6-5.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 | # $Id$
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for using the Class 1 command interface with
# a Digicom Systems, Inc (DSI) Scout+ modem. Firmware version
# 2A19/2931 (ati1?) or newer.
#
# XON/XOFF flow control must be used in firmware revisions before
# 3507/3506 because the modem does not honor RTS/CTS during page
# transfers. Later revisions permit the configuration of RTS/CTS
# flow control through a new (undocumented) register, S24:
#
# Value Meaning
# 0 use XON/XOFF in fax mode
# 1 use RTS/CTS in fax mode
# 2 use what is specified by *F in fax mode
#
# Note also that the value of S24 is not permanent. It is reset
# after each disconnect. On power on S24 is 0. S24 is unchanged
# by the &F command.
#
# CONFIG:CLASS1:961:.*:.*: Manufacturer=Digicom Model=Scout+
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # hint to override class 2
ModemRate: 19200
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT*F0 # disable flow control
ModemSoftFlowCmd: AT*F2 # software flow control
ModemHardFlowCmd: AT*F3 # harware flow control
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
#
Class1SFLOCmd: ATS24=0 # use XON/XOFF in fax mode
Class1HFLOCmd: ATS24=1 # use RTS/CTS in fax mode
#
ModemMfrQueryCmd: !Digicom
ModemModelQueryCmd: !Scout+
ModemRevQueryCmd: ATI1
#
ModemDialCmd: ATDT%s # T for tone dialing
#
# NB: if your modem supports S24 as described above then
# these can be removed.
#
ModemAnswerFaxBeginCmd: "<xon>" # use XON/XOFF for fax recv
Class1Cmd: "AT+FCLASS=1\n<xon>" # use XON/XOFF for fax send
|