/usr/share/gtk-doc/html/NetworkManager/nm-settings.html is in network-manager-dev 1.10.6-2ubuntu1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2629 2630 2631 2632 2633 2634 2635 2636 2637 2638 2639 2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650 2651 2652 2653 2654 2655 2656 2657 2658 2659 2660 2661 2662 2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673 2674 2675 2676 2677 2678 2679 2680 2681 2682 2683 2684 2685 2686 2687 2688 2689 2690 2691 2692 2693 2694 2695 2696 2697 2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2715 2716 2717 2718 2719 2720 2721 2722 2723 2724 2725 2726 2727 2728 2729 2730 2731 2732 2733 2734 2735 2736 2737 2738 2739 2740 2741 2742 2743 2744 2745 2746 2747 2748 2749 2750 2751 2752 2753 2754 2755 2756 2757 2758 2759 2760 2761 2762 2763 2764 2765 2766 2767 2768 2769 2770 2771 2772 2773 2774 2775 2776 2777 2778 2779 2780 2781 2782 2783 2784 2785 2786 2787 2788 2789 2790 2791 2792 2793 2794 2795 2796 2797 2798 2799 2800 2801 2802 2803 2804 2805 2806 2807 2808 2809 2810 2811 2812 2813 2814 2815 2816 2817 2818 2819 2820 2821 2822 2823 2824 2825 2826 2827 2828 2829 2830 2831 2832 2833 2834 2835 2836 2837 2838 2839 2840 2841 2842 2843 2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854 2855 2856 2857 2858 2859 2860 2861 2862 2863 2864 2865 2866 2867 2868 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878 2879 2880 2881 2882 2883 2884 2885 2886 2887 2888 2889 2890 2891 2892 2893 2894 2895 2896 2897 2898 2899 2900 2901 2902 2903 2904 2905 2906 2907 2908 2909 2910 2911 2912 2913 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923 2924 2925 2926 2927 2928 2929 2930 2931 2932 2933 2934 2935 2936 2937 2938 2939 2940 2941 2942 2943 2944 2945 2946 2947 2948 2949 2950 2951 2952 2953 2954 2955 2956 2957 2958 2959 2960 2961 2962 2963 2964 2965 2966 2967 2968 2969 2970 2971 2972 2973 2974 2975 2976 2977 2978 2979 2980 2981 2982 2983 2984 2985 2986 2987 2988 2989 2990 2991 2992 2993 2994 2995 2996 2997 2998 2999 3000 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048 3049 3050 3051 3052 3053 3054 3055 3056 3057 3058 3059 3060 3061 3062 3063 3064 3065 3066 3067 3068 3069 3070 3071 3072 3073 3074 3075 3076 3077 3078 3079 3080 3081 3082 3083 3084 3085 3086 3087 3088 3089 3090 3091 3092 3093 3094 3095 3096 3097 3098 3099 3100 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3111 3112 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3126 3127 3128 3129 3130 3131 3132 3133 3134 3135 3136 3137 3138 3139 3140 3141 3142 3143 3144 3145 3146 3147 3148 3149 3150 3151 3152 3153 3154 3155 3156 3157 3158 3159 3160 3161 3162 3163 3164 3165 3166 3167 3168 3169 3170 3171 3172 3173 3174 3175 3176 3177 3178 3179 3180 3181 3182 3183 3184 3185 3186 3187 3188 3189 3190 3191 3192 3193 3194 3195 3196 3197 3198 3199 3200 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3213 3214 3215 3216 3217 3218 3219 3220 3221 3222 3223 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 3237 3238 3239 3240 3241 3242 3243 3244 3245 3246 3247 3248 3249 3250 3251 3252 3253 3254 3255 3256 3257 3258 3259 3260 3261 3262 3263 3264 3265 3266 3267 3268 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3281 3282 3283 3284 3285 3286 3287 3288 3289 3290 3291 3292 3293 3294 3295 3296 3297 3298 3299 3300 3301 3302 3303 3304 3305 3306 3307 3308 3309 3310 3311 3312 3313 3314 3315 3316 3317 3318 3319 3320 3321 3322 3323 3324 3325 3326 3327 3328 3329 3330 3331 3332 3333 3334 3335 3336 3337 3338 3339 3340 3341 3342 3343 3344 3345 3346 3347 3348 3349 3350 3351 3352 3353 3354 3355 3356 3357 3358 3359 3360 3361 3362 3363 3364 3365 3366 3367 3368 3369 3370 3371 3372 3373 3374 3375 3376 3377 3378 3379 3380 3381 3382 3383 3384 3385 3386 3387 3388 3389 3390 3391 3392 3393 3394 3395 3396 3397 3398 3399 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 3410 3411 3412 3413 3414 3415 3416 3417 3418 3419 3420 3421 3422 3423 3424 3425 3426 3427 3428 3429 3430 3431 3432 3433 3434 3435 3436 3437 3438 3439 3440 3441 3442 3443 3444 3445 3446 3447 3448 3449 3450 3451 3452 3453 3454 3455 3456 3457 3458 3459 3460 3461 3462 3463 3464 3465 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3476 3477 3478 3479 3480 3481 3482 3483 3484 3485 3486 3487 3488 3489 3490 3491 3492 3493 3494 3495 3496 3497 3498 3499 3500 3501 3502 3503 3504 3505 3506 3507 3508 3509 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3525 3526 3527 3528 3529 3530 3531 3532 3533 3534 3535 3536 3537 3538 3539 3540 3541 3542 3543 3544 3545 3546 3547 3548 3549 3550 3551 3552 3553 3554 3555 3556 3557 3558 3559 3560 3561 3562 3563 3564 3565 3566 3567 3568 3569 3570 3571 3572 3573 3574 3575 3576 3577 3578 3579 3580 3581 3582 3583 3584 3585 3586 3587 3588 3589 3590 3591 3592 3593 3594 3595 3596 3597 3598 3599 3600 3601 3602 3603 3604 3605 3606 3607 3608 3609 3610 3611 3612 3613 3614 3615 3616 3617 3618 3619 3620 3621 3622 3623 3624 3625 3626 3627 3628 3629 3630 3631 3632 3633 3634 3635 3636 3637 3638 3639 3640 3641 3642 3643 3644 3645 3646 3647 3648 3649 3650 3651 3652 3653 3654 3655 3656 3657 3658 3659 3660 3661 3662 3663 3664 3665 3666 3667 3668 3669 3670 3671 3672 3673 3674 3675 3676 3677 3678 3679 3680 3681 3682 3683 3684 3685 3686 3687 3688 3689 3690 3691 3692 3693 3694 3695 3696 3697 3698 3699 3700 3701 3702 3703 3704 3705 3706 3707 3708 3709 3710 3711 3712 3713 3714 3715 3716 3717 3718 3719 3720 3721 3722 | <!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
<title>nm-settings: NetworkManager Reference Manual</title>
<meta name="generator" content="DocBook XSL Stylesheets V1.79.1">
<link rel="home" href="index.html" title="NetworkManager Reference Manual">
<link rel="up" href="manpages.html" title="Part I. Manual Pages">
<link rel="prev" href="nmtui.html" title="nmtui">
<link rel="next" href="nm-settings-keyfile.html" title="nm-settings-keyfile">
<meta name="generator" content="GTK-Doc V1.27 (XML mode)">
<link rel="stylesheet" href="style.css" type="text/css">
</head>
<body bgcolor="white" text="black" link="#0000FF" vlink="#840084" alink="#0000FF">
<table class="navigation" id="top" width="100%" summary="Navigation header" cellpadding="2" cellspacing="5"><tr valign="middle">
<td width="100%" align="left" class="shortcuts"></td>
<td><a accesskey="h" href="index.html"><img src="home.png" width="16" height="16" border="0" alt="Home"></a></td>
<td><a accesskey="u" href="manpages.html"><img src="up.png" width="16" height="16" border="0" alt="Up"></a></td>
<td><a accesskey="p" href="nmtui.html"><img src="left.png" width="16" height="16" border="0" alt="Prev"></a></td>
<td><a accesskey="n" href="nm-settings-keyfile.html"><img src="right.png" width="16" height="16" border="0" alt="Next"></a></td>
</tr></table>
<div class="refentry">
<a name="nm-settings"></a><div class="titlepage"></div>
<div class="refnamediv"><table width="100%"><tr>
<td valign="top">
<h2><span class="refentrytitle">nm-settings</span></h2>
<p>nm-settings — Description of settings and properties of NetworkManager connection profiles</p>
</td>
<td class="gallery_image" valign="top" align="right"></td>
</tr></table></div>
<div class="refsect1">
<a name="description"></a><h2>Description</h2>
<p>
NetworkManager is based on a concept of connection profiles, sometimes referred to as
connections only. These connection profiles contain a network configuration. When
NetworkManager activates a connection profile on a network device the configuration will
be applied and an active network connection will be established. Users are free to create
as many connection profiles as they see fit. Thus they are flexible in having various network
configurations for different networking needs. The connection profiles are handled by
NetworkManager via <span class="emphasis"><em>settings service</em></span> and are exported on D-Bus
(<span class="emphasis"><em>/org/freedesktop/NetworkManager/Settings/<num></em></span> objects).
The conceptual objects can be described as follows:
</p>
<div class="variablelist"><table border="0" class="variablelist">
<colgroup>
<col align="left" valign="top">
<col>
</colgroup>
<tbody><tr>
<td><p><span class="term">Connection (profile)</span></p></td>
<td><p>
A specific, encapsulated, independent group of settings describing
all the configuration required to connect to a specific network.
It is referred to by a unique identifier called the UUID. A connection
is tied to a one specific device type, but not necessarily a specific
hardware device. It is composed of one or more <span class="emphasis"><em>Settings</em></span>
objects.
</p></td>
</tr></tbody>
</table></div>
<div class="variablelist"><table border="0" class="variablelist">
<colgroup>
<col align="left" valign="top">
<col>
</colgroup>
<tbody><tr>
<td><p><span class="term">Setting</span></p></td>
<td><p>
A group of related key/value pairs describing a specific piece of a
<span class="emphasis"><em>Connection (profile)</em></span>. Settings keys and allowed values are
described in the tables below. Keys are also referred to as properties.
Developers can find the setting objects and their properties in the libnm-core
sources. Look for the <code class="function">*_class_init</code> functions near the bottom
of each setting source file.
</p></td>
</tr></tbody>
</table></div>
<div class="variablelist">
<p>
The settings and properties shown in tables below list all available connection
configuration options. However, note that not all settings are applicable to all
connection types. NetworkManager provides a command-line tool <span class="emphasis"><em>nmcli</em></span>
that allows direct configuration of the settings and properties according to a connection
profile type. <span class="emphasis"><em>nmcli</em></span> connection editor has also a built-in
<span class="emphasis"><em>describe</em></span> command that can display description of particular settings
and properties of this page.
</p>
<table border="0" class="variablelist">
<colgroup>
<col align="left" valign="top">
<col>
</colgroup>
<tbody></tbody>
</table>
</div>
<div class="refsect2">
<a name="id-1.2.7.4.3"></a><h3>connection setting</h3>
<p>General Connection Profile Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.connection.auth-retries"></a>auth-retries</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The number of retries for the authentication. Zero means to try indefinitely; -1 means to use a global default. If the global default is not set, the authentication retries for 3 times before failing the connection. Currently this only applies to 802-1x authentication.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.autoconnect"></a>autoconnect</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Whether or not the connection should be automatically connected by NetworkManager when the resources for the connection are available. TRUE to automatically activate the connection, FALSE to require manual intervention to activate the connection.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.autoconnect-priority"></a>autoconnect-priority</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>The autoconnect priority. If the connection is set to autoconnect, connections with higher priority will be preferred. Defaults to 0. The higher number means higher priority.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.autoconnect-retries"></a>autoconnect-retries</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The number of times a connection should be tried when autoactivating before giving up. Zero means forever, -1 means the global default (4 times if not overridden). Setting this to 1 means to try activation only once before blocking autoconnect. Note that after a timeout, NetworkManager will try to autoconnect again.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.autoconnect-slaves"></a>autoconnect-slaves</td>
<td align="left">NMSettingConnectionAutoconnectSlaves (int32)</td>
<td align="left"> </td>
<td>Whether or not slaves of this connection should be automatically brought up when NetworkManager activates this connection. This only has a real effect for master connections. The permitted values are: 0: leave slave connections untouched, 1: activate all the slave connections with this connection, -1: default. If -1 (default) is set, global connection.autoconnect-slaves is read to determine the real value. If it is default as well, this fallbacks to 0.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.gateway-ping-timeout"></a>gateway-ping-timeout</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If greater than zero, delay success of IP addressing until either the timeout is reached, or an IP gateway replies to a ping.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.id"></a>id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>A human readable unique identifier for the connection, like "Work Wi-Fi" or "T-Mobile 3G".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.interface-name"></a>interface-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The name of the network interface this connection is bound to. If not set, then the connection can be attached to any interface of the appropriate type (subject to restrictions imposed by other settings). For software devices this specifies the name of the created device. For connection types where interface names cannot easily be made persistent (e.g. mobile broadband or USB Ethernet), this property should not be used. Setting this property restricts the interfaces a connection can be used with, and if interface names change or are reordered the connection may be applied to the wrong interface.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.lldp"></a>lldp</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Whether LLDP is enabled for the connection.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.master"></a>master</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Interface name of the master device or UUID of the master connection.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.metered"></a>metered</td>
<td align="left">NMMetered (int32)</td>
<td align="left"> </td>
<td>Whether the connection is metered. When updating this property on a currently activated connection, the change takes effect immediately.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.name"></a>name</td>
<td align="left">string</td>
<td align="left">connection</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.permissions"></a>permissions</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>An array of strings defining what access a given user has to this connection. If this is NULL or empty, all users are allowed to access this connection; otherwise users are allowed if and only if they are in this list. When this is not empty, the connection can be active only when one of the specified users is logged into an active session. Each entry is of the form "[type]:[id]:[reserved]"; for example, "user:dcbw:blah". At this time only the "user" [type] is allowed. Any other values are ignored and reserved for future use. [id] is the username that this permission refers to, which may not contain the ":" character. Any [reserved] information present must be ignored and is reserved for future use. All of [type], [id], and [reserved] must be valid UTF-8.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.read-only"></a>read-only</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>FALSE if the connection can be modified using the provided settings service's D-Bus interface with the right privileges, or TRUE if the connection is read-only and cannot be modified.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.secondaries"></a>secondaries</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>List of connection UUIDs that should be activated when the base connection itself is activated. Currently only VPN connections are supported.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.slave-type"></a>slave-type</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Setting name of the device type of this slave's master connection (eg, "bond"), or NULL if this connection is not a slave.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.stable-id"></a>stable-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Token to generate stable IDs for the connection. The stable-id is used for generating IPv6 stable private addresses with ipv6.addr-gen-mode=stable-privacy. It is also used to seed the generated cloned MAC address for ethernet.cloned-mac-address=stable and wifi.cloned-mac-address=stable. Note that also the interface name of the activating connection and a per-host secret key is included into the address generation so that the same stable-id on different hosts/devices yields different addresses. If the value is unset, an ID unique for the connection is used. Specifying a stable-id allows multiple connections to generate the same addresses. Another use is to generate IDs at runtime via dynamic substitutions. The '$' character is treated special to perform dynamic substitutions at runtime. Currently supported are "${CONNECTION}", "${BOOT}", "${RANDOM}". These effectively create unique IDs per-connection, per-boot, or every time. Any unrecognized patterns following '$' are treated verbatim, however are reserved for future use. You are thus advised to avoid '$' or escape it as "$$". For example, set it to "${CONNECTION}/${BOOT}" to create a unique id for this connection that changes with every reboot. Note that two connections only use the same effective id if their stable-id is also identical before performing dynamic substitutions.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.timestamp"></a>timestamp</td>
<td align="left">uint64</td>
<td align="left">0</td>
<td>The time, in seconds since the Unix Epoch, that the connection was last _successfully_ fully activated. NetworkManager updates the connection timestamp periodically when the connection is active to ensure that an active connection has the latest timestamp. The property is only meant for reading (changes to this property will not be preserved).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.type"></a>type</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Base type of the connection. For hardware-dependent connections, should contain the setting name of the hardware-type specific setting (ie, "802-3-ethernet" or "802-11-wireless" or "bluetooth", etc), and for non-hardware dependent connections like VPN or otherwise, should contain the setting name of that setting type (ie, "vpn" or "bridge", etc).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.uuid"></a>uuid</td>
<td align="left">string</td>
<td align="left"> </td>
<td>A universally unique identifier for the connection, for example generated with libuuid. It should be assigned when the connection is created, and never changed as long as the connection still applies to the same network. For example, it should not be changed when the "id" property or NMSettingIP4Config changes, but might need to be re-created when the Wi-Fi SSID, mobile broadband network provider, or "type" property changes. The UUID must be in the format "2815492f-7e56-435e-b2e9-246bd7cdc664" (ie, contains only hexadecimal characters and "-").</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.connection.zone"></a>zone</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The trust level of a the connection. Free form case-insensitive string (for example "Home", "Work", "Public"). NULL or unspecified zone means the connection will be placed in the default zone as defined by the firewall. When updating this property on a currently activated connection, the change takes effect immediately.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.4"></a><h3>802-1x setting</h3>
<p>IEEE 802.1x Authentication Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.altsubject-matches"></a>altsubject-matches</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>List of strings to be matched against the altSubjectName of the certificate presented by the authentication server. If the list is empty, no verification of the server certificate's altSubjectName is performed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.anonymous-identity"></a>anonymous-identity</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Anonymous identity string for EAP authentication methods. Used as the unencrypted identity with EAP types that support different tunneled identity like EAP-TTLS.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.auth-timeout"></a>auth-timeout</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>A timeout for the authentication. Zero means the global default; if the global default is not set, the authentication timeout is 25 seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.ca-cert"></a>ca-cert</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the CA certificate if used by the EAP method specified in the "eap" property. Certificate data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme (which is backwards compatible with NM 0.7.x) this property should be set to the certificate's DER encoded data. When using the path scheme, this property should be set to the full UTF-8 encoded path of the certificate, prefixed with the string "file://" and ending with a terminating NUL byte. This property can be unset even if the EAP method supports CA certificates, but this allows man-in-the-middle attacks and is NOT recommended.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.ca-cert-password"></a>ca-cert-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to access the CA certificate stored in "ca-cert" property. Only makes sense if the certificate is stored on a PKCS#11 token that requires a login.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.ca-cert-password-flags"></a>ca-cert-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "ca-cert-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.ca-path"></a>ca-path</td>
<td align="left">string</td>
<td align="left"> </td>
<td>UTF-8 encoded path to a directory containing PEM or DER formatted certificates to be added to the verification chain in addition to the certificate specified in the "ca-cert" property.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.client-cert"></a>client-cert</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the client certificate if used by the EAP method specified in the "eap" property. Certificate data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme (which is backwards compatible with NM 0.7.x) this property should be set to the certificate's DER encoded data. When using the path scheme, this property should be set to the full UTF-8 encoded path of the certificate, prefixed with the string "file://" and ending with a terminating NUL byte.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.client-cert-password"></a>client-cert-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to access the client certificate stored in "client-cert" property. Only makes sense if the certificate is stored on a PKCS#11 token that requires a login.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.client-cert-password-flags"></a>client-cert-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "client-cert-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.domain-suffix-match"></a>domain-suffix-match</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Constraint for server domain name. If set, this FQDN is used as a suffix match requirement for dNSName element(s) of the certificate presented by the authentication server. If a matching dNSName is found, this constraint is met. If no dNSName values are present, this constraint is matched against SubjectName CN using same suffix match comparison.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.eap"></a>eap</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>The allowed EAP method to be used when authenticating to the network with 802.1x. Valid methods are: "leap", "md5", "tls", "peap", "ttls", "pwd", and "fast". Each method requires different configuration using the properties of this setting; refer to wpa_supplicant documentation for the allowed combinations.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.identity"></a>identity</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Identity string for EAP authentication methods. Often the user's user or login name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.name"></a>name</td>
<td align="left">string</td>
<td align="left">802-1x</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.pac-file"></a>pac-file</td>
<td align="left">string</td>
<td align="left"> </td>
<td>UTF-8 encoded file path containing PAC for EAP-FAST.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.password"></a>password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>UTF-8 encoded password used for EAP authentication methods. If both the "password" property and the "password-raw" property are specified, "password" is preferred.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.password-flags"></a>password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.password-raw"></a>password-raw</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Password used for EAP authentication methods, given as a byte array to allow passwords in other encodings than UTF-8 to be used. If both the "password" property and the "password-raw" property are specified, "password" is preferred.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.password-raw-flags"></a>password-raw-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password-raw" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase1-auth-flags"></a>phase1-auth-flags</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies authentication flags to use in "phase 1" outer authentication using NMSetting8021xAuthFlags options. The individual TLS versions can be explicitly disabled. If a certain TLS disable flag is not set, it is up to the supplicant to allow or forbid it. The TLS options map to tls_disable_tlsv1_x settings. See the wpa_supplicant documentation for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase1-fast-provisioning"></a>phase1-fast-provisioning</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Enables or disables in-line provisioning of EAP-FAST credentials when FAST is specified as the EAP method in the "eap" property. Recognized values are "0" (disabled), "1" (allow unauthenticated provisioning), "2" (allow authenticated provisioning), and "3" (allow both authenticated and unauthenticated provisioning). See the wpa_supplicant documentation for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase1-peaplabel"></a>phase1-peaplabel</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Forces use of the new PEAP label during key derivation. Some RADIUS servers may require forcing the new PEAP label to interoperate with PEAPv1. Set to "1" to force use of the new PEAP label. See the wpa_supplicant documentation for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase1-peapver"></a>phase1-peapver</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Forces which PEAP version is used when PEAP is set as the EAP method in the "eap" property. When unset, the version reported by the server will be used. Sometimes when using older RADIUS servers, it is necessary to force the client to use a particular PEAP version. To do so, this property may be set to "0" or "1" to force that specific PEAP version.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-altsubject-matches"></a>phase2-altsubject-matches</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>List of strings to be matched against the altSubjectName of the certificate presented by the authentication server during the inner "phase 2" authentication. If the list is empty, no verification of the server certificate's altSubjectName is performed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-auth"></a>phase2-auth</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Specifies the allowed "phase 2" inner non-EAP authentication methods when an EAP method that uses an inner TLS tunnel is specified in the "eap" property. Recognized non-EAP "phase 2" methods are "pap", "chap", "mschap", "mschapv2", "gtc", "otp", "md5", and "tls". Each "phase 2" inner method requires specific parameters for successful authentication; see the wpa_supplicant documentation for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-autheap"></a>phase2-autheap</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Specifies the allowed "phase 2" inner EAP-based authentication methods when an EAP method that uses an inner TLS tunnel is specified in the "eap" property. Recognized EAP-based "phase 2" methods are "md5", "mschapv2", "otp", "gtc", and "tls". Each "phase 2" inner method requires specific parameters for successful authentication; see the wpa_supplicant documentation for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-ca-cert"></a>phase2-ca-cert</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the "phase 2" CA certificate if used by the EAP method specified in the "phase2-auth" or "phase2-autheap" properties. Certificate data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme (which is backwards compatible with NM 0.7.x) this property should be set to the certificate's DER encoded data. When using the path scheme, this property should be set to the full UTF-8 encoded path of the certificate, prefixed with the string "file://" and ending with a terminating NUL byte. This property can be unset even if the EAP method supports CA certificates, but this allows man-in-the-middle attacks and is NOT recommended.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-ca-cert-password"></a>phase2-ca-cert-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to access the "phase2" CA certificate stored in "phase2-ca-cert" property. Only makes sense if the certificate is stored on a PKCS#11 token that requires a login.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-ca-cert-password-flags"></a>phase2-ca-cert-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "phase2-ca-cert-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-ca-path"></a>phase2-ca-path</td>
<td align="left">string</td>
<td align="left"> </td>
<td>UTF-8 encoded path to a directory containing PEM or DER formatted certificates to be added to the verification chain in addition to the certificate specified in the "phase2-ca-cert" property.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-client-cert"></a>phase2-client-cert</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the "phase 2" client certificate if used by the EAP method specified in the "phase2-auth" or "phase2-autheap" properties. Certificate data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme (which is backwards compatible with NM 0.7.x) this property should be set to the certificate's DER encoded data. When using the path scheme, this property should be set to the full UTF-8 encoded path of the certificate, prefixed with the string "file://" and ending with a terminating NUL byte. This property can be unset even if the EAP method supports CA certificates, but this allows man-in-the-middle attacks and is NOT recommended.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-client-cert-password"></a>phase2-client-cert-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to access the "phase2" client certificate stored in "phase2-client-cert" property. Only makes sense if the certificate is stored on a PKCS#11 token that requires a login.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-client-cert-password-flags"></a>phase2-client-cert-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "phase2-client-cert-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-domain-suffix-match"></a>phase2-domain-suffix-match</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Constraint for server domain name. If set, this FQDN is used as a suffix match requirement for dNSName element(s) of the certificate presented by the authentication server during the inner "phase 2" authentication. If a matching dNSName is found, this constraint is met. If no dNSName values are present, this constraint is matched against SubjectName CN using same suffix match comparison.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-private-key"></a>phase2-private-key</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the "phase 2" inner private key when the "phase2-auth" or "phase2-autheap" property is set to "tls". Key data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme and private keys, this property should be set to the key's encrypted PEM encoded data. When using private keys with the path scheme, this property should be set to the full UTF-8 encoded path of the key, prefixed with the string "file://" and ending with a terminating NUL byte. When using PKCS#12 format private keys and the blob scheme, this property should be set to the PKCS#12 data and the "phase2-private-key-password" property must be set to password used to decrypt the PKCS#12 certificate and key. When using PKCS#12 files and the path scheme, this property should be set to the full UTF-8 encoded path of the key, prefixed with the string "file://" and ending with a terminating NUL byte, and as with the blob scheme the "phase2-private-key-password" property must be set to the password used to decode the PKCS#12 private key and certificate.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-private-key-password"></a>phase2-private-key-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to decrypt the "phase 2" private key specified in the "phase2-private-key" property when the private key either uses the path scheme, or is a PKCS#12 format key.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-private-key-password-flags"></a>phase2-private-key-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "phase2-private-key-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.phase2-subject-match"></a>phase2-subject-match</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Substring to be matched against the subject of the certificate presented by the authentication server during the inner "phase 2" authentication. When unset, no verification of the authentication server certificate's subject is performed. This property provides little security, if any, and its use is deprecated in favor of NMSetting8021x:phase2-domain-suffix-match.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.pin"></a>pin</td>
<td align="left">string</td>
<td align="left"> </td>
<td>PIN used for EAP authentication methods.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.pin-flags"></a>pin-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "pin" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.private-key"></a>private-key</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Contains the private key when the "eap" property is set to "tls". Key data is specified using a "scheme"; two are currently supported: blob and path. When using the blob scheme and private keys, this property should be set to the key's encrypted PEM encoded data. When using private keys with the path scheme, this property should be set to the full UTF-8 encoded path of the key, prefixed with the string "file://" and ending with a terminating NUL byte. When using PKCS#12 format private keys and the blob scheme, this property should be set to the PKCS#12 data and the "private-key-password" property must be set to password used to decrypt the PKCS#12 certificate and key. When using PKCS#12 files and the path scheme, this property should be set to the full UTF-8 encoded path of the key, prefixed with the string "file://" and ending with a terminating NUL byte, and as with the blob scheme the "private-key-password" property must be set to the password used to decode the PKCS#12 private key and certificate. WARNING: "private-key" is not a "secret" property, and thus unencrypted private key data using the BLOB scheme may be readable by unprivileged users. Private keys should always be encrypted with a private key password to prevent unauthorized access to unencrypted private key data.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.private-key-password"></a>private-key-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to decrypt the private key specified in the "private-key" property when the private key either uses the path scheme, or if the private key is a PKCS#12 format key.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.private-key-password-flags"></a>private-key-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "private-key-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.subject-match"></a>subject-match</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Substring to be matched against the subject of the certificate presented by the authentication server. When unset, no verification of the authentication server certificate's subject is performed. This property provides little security, if any, and its use is deprecated in favor of NMSetting8021x:domain-suffix-match.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-1x.system-ca-certs"></a>system-ca-certs</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When TRUE, overrides the "ca-path" and "phase2-ca-path" properties using the system CA directory specified at configure time with the --system-ca-path switch. The certificates in this directory are added to the verification chain in addition to any certificates specified by the "ca-cert" and "phase2-ca-cert" properties. If the path provided with --system-ca-path is rather a file name (bundle of trusted CA certificates), it overrides "ca-cert" and "phase2-ca-cert" properties instead (sets ca_cert/ca_cert2 options for wpa_supplicant).</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.5"></a><h3>adsl setting</h3>
<p>ADSL Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.encapsulation"></a>encapsulation</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Encapsulation of ADSL connection. Can be "vcmux" or "llc".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.name"></a>name</td>
<td align="left">string</td>
<td align="left">adsl</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.password"></a>password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Password used to authenticate with the ADSL service.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.password-flags"></a>password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.protocol"></a>protocol</td>
<td align="left">string</td>
<td align="left"> </td>
<td>ADSL connection protocol. Can be "pppoa", "pppoe" or "ipoatm".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.username"></a>username</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Username used to authenticate with the ADSL service.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.vci"></a>vci</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>VCI of ADSL connection</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.adsl.vpi"></a>vpi</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>VPI of ADSL connection</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.6"></a><h3>bluetooth setting</h3>
<p>Bluetooth Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.bluetooth.bdaddr"></a>bdaddr</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>The Bluetooth address of the device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bluetooth.name"></a>name</td>
<td align="left">string</td>
<td align="left">bluetooth</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bluetooth.type"></a>type</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Either "dun" for Dial-Up Networking connections or "panu" for Personal Area Networking connections to devices supporting the NAP profile.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.7"></a><h3>bond setting</h3>
<p>Bonding Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.bond.interface-name"></a>interface-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Deprecated in favor of connection.interface-name, but can be used for backward-compatibility with older daemons, to set the bond's interface name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bond.name"></a>name</td>
<td align="left">string</td>
<td align="left">bond</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bond.options"></a>options</td>
<td align="left">dict of string to string</td>
<td align="left">{'mode': 'balance-rr'}</td>
<td>Dictionary of key/value pairs of bonding options. Both keys and values must be strings. Option names must contain only alphanumeric characters (ie, [a-zA-Z0-9]).</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.8"></a><h3>bridge setting</h3>
<p>Bridging Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.ageing-time"></a>ageing-time</td>
<td align="left">uint32</td>
<td align="left">300</td>
<td>The Ethernet MAC address aging time, in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.forward-delay"></a>forward-delay</td>
<td align="left">uint32</td>
<td align="left">15</td>
<td>The Spanning Tree Protocol (STP) forwarding delay, in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.group-forward-mask"></a>group-forward-mask</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>A mask of group addresses to forward. Usually, group addresses in the range from 01:80:C2:00:00:00 to 01:80:C2:00:00:0F are not forwarded according to standards. This property is a mask of 16 bits, each corresponding to a group address in that range that must be forwarded. The mask can't have bits 0, 1 or 2 set because they are used for STP, MAC pause frames and LACP.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.hello-time"></a>hello-time</td>
<td align="left">uint32</td>
<td align="left">2</td>
<td>The Spanning Tree Protocol (STP) hello time, in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.interface-name"></a>interface-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Deprecated in favor of connection.interface-name, but can be used for backward-compatibility with older daemons, to set the bridge's interface name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.mac-address"></a>mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, the MAC address of bridge. When creating a new bridge, this MAC address will be set. If this field is left unspecified, the "ethernet.cloned-mac-address" is referred instead to generate the initial MAC address. Note that setting "ethernet.cloned-mac-address" anyway overwrites the MAC address of the bridge later while activating the bridge. Hence, this property is deprecated.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.max-age"></a>max-age</td>
<td align="left">uint32</td>
<td align="left">20</td>
<td>The Spanning Tree Protocol (STP) maximum message age, in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.multicast-snooping"></a>multicast-snooping</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Controls whether IGMP snooping is enabled for this bridge. Note that if snooping was automatically disabled due to hash collisions, the system may refuse to enable the feature until the collisions are resolved.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.name"></a>name</td>
<td align="left">string</td>
<td align="left">bridge</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.priority"></a>priority</td>
<td align="left">uint32</td>
<td align="left">32768</td>
<td>Sets the Spanning Tree Protocol (STP) priority for this bridge. Lower values are "better"; the lowest priority bridge will be elected the root bridge.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge.stp"></a>stp</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Controls whether Spanning Tree Protocol (STP) is enabled for this bridge.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.9"></a><h3>bridge-port setting</h3>
<p>Bridge Port Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.bridge-port.hairpin-mode"></a>hairpin-mode</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Enables or disables "hairpin mode" for the port, which allows frames to be sent back out through the port the frame was received on.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge-port.name"></a>name</td>
<td align="left">string</td>
<td align="left">bridge-port</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge-port.path-cost"></a>path-cost</td>
<td align="left">uint32</td>
<td align="left">100</td>
<td>The Spanning Tree Protocol (STP) port cost for destinations via this port.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.bridge-port.priority"></a>priority</td>
<td align="left">uint32</td>
<td align="left">32</td>
<td>The Spanning Tree Protocol (STP) priority of this bridge port.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.10"></a><h3>cdma setting</h3>
<p>CDMA-based Mobile Broadband Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple frames.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.name"></a>name</td>
<td align="left">string</td>
<td align="left">cdma</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.number"></a>number</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The number to dial to establish the connection to the CDMA-based mobile broadband network, if any. If not specified, the default number (#777) is used when required.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.password"></a>password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to authenticate with the network, if required. Many providers do not require a password, or accept any password. But if a password is required, it is specified here.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.password-flags"></a>password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.cdma.username"></a>username</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The username used to authenticate with the network, if required. Many providers do not require a username, or accept any username. But if a username is required, it is specified here.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.11"></a><h3>dcb setting</h3>
<p>Data Center Bridging Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-fcoe-flags"></a>app-fcoe-flags</td>
<td align="left">NMSettingDcbFlags (uint32)</td>
<td align="left"> </td>
<td>Specifies the NMSettingDcbFlags for the DCB FCoE application. Flags may be any combination of NM_SETTING_DCB_FLAG_ENABLE (0x1), NM_SETTING_DCB_FLAG_ADVERTISE (0x2), and NM_SETTING_DCB_FLAG_WILLING (0x4).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-fcoe-mode"></a>app-fcoe-mode</td>
<td align="left">string</td>
<td align="left">"fabric"</td>
<td>The FCoE controller mode; either "fabric" (default) or "vn2vn".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-fcoe-priority"></a>app-fcoe-priority</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The highest User Priority (0 - 7) which FCoE frames should use, or -1 for default priority. Only used when the "app-fcoe-flags" property includes the NM_SETTING_DCB_FLAG_ENABLE (0x1) flag.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-fip-flags"></a>app-fip-flags</td>
<td align="left">NMSettingDcbFlags (uint32)</td>
<td align="left"> </td>
<td>Specifies the NMSettingDcbFlags for the DCB FIP application. Flags may be any combination of NM_SETTING_DCB_FLAG_ENABLE (0x1), NM_SETTING_DCB_FLAG_ADVERTISE (0x2), and NM_SETTING_DCB_FLAG_WILLING (0x4).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-fip-priority"></a>app-fip-priority</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The highest User Priority (0 - 7) which FIP frames should use, or -1 for default priority. Only used when the "app-fip-flags" property includes the NM_SETTING_DCB_FLAG_ENABLE (0x1) flag.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-iscsi-flags"></a>app-iscsi-flags</td>
<td align="left">NMSettingDcbFlags (uint32)</td>
<td align="left"> </td>
<td>Specifies the NMSettingDcbFlags for the DCB iSCSI application. Flags may be any combination of NM_SETTING_DCB_FLAG_ENABLE (0x1), NM_SETTING_DCB_FLAG_ADVERTISE (0x2), and NM_SETTING_DCB_FLAG_WILLING (0x4).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.app-iscsi-priority"></a>app-iscsi-priority</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The highest User Priority (0 - 7) which iSCSI frames should use, or -1 for default priority. Only used when the "app-iscsi-flags" property includes the NM_SETTING_DCB_FLAG_ENABLE (0x1) flag.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.name"></a>name</td>
<td align="left">string</td>
<td align="left">dcb</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-bandwidth"></a>priority-bandwidth</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 uint values, where the array index corresponds to the User Priority (0 - 7) and the value indicates the percentage of bandwidth of the priority's assigned group that the priority may use. The sum of all percentages for priorities which belong to the same group must total 100 percents.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-flow-control"></a>priority-flow-control</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 boolean values, where the array index corresponds to the User Priority (0 - 7) and the value indicates whether or not the corresponding priority should transmit priority pause.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-flow-control-flags"></a>priority-flow-control-flags</td>
<td align="left">NMSettingDcbFlags (uint32)</td>
<td align="left"> </td>
<td>Specifies the NMSettingDcbFlags for DCB Priority Flow Control (PFC). Flags may be any combination of NM_SETTING_DCB_FLAG_ENABLE (0x1), NM_SETTING_DCB_FLAG_ADVERTISE (0x2), and NM_SETTING_DCB_FLAG_WILLING (0x4).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-group-bandwidth"></a>priority-group-bandwidth</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 uint values, where the array index corresponds to the Priority Group ID (0 - 7) and the value indicates the percentage of link bandwidth allocated to that group. Allowed values are 0 - 100, and the sum of all values must total 100 percents.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-group-flags"></a>priority-group-flags</td>
<td align="left">NMSettingDcbFlags (uint32)</td>
<td align="left"> </td>
<td>Specifies the NMSettingDcbFlags for DCB Priority Groups. Flags may be any combination of NM_SETTING_DCB_FLAG_ENABLE (0x1), NM_SETTING_DCB_FLAG_ADVERTISE (0x2), and NM_SETTING_DCB_FLAG_WILLING (0x4).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-group-id"></a>priority-group-id</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 uint values, where the array index corresponds to the User Priority (0 - 7) and the value indicates the Priority Group ID. Allowed Priority Group ID values are 0 - 7 or 15 for the unrestricted group.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-strict-bandwidth"></a>priority-strict-bandwidth</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 boolean values, where the array index corresponds to the User Priority (0 - 7) and the value indicates whether or not the priority may use all of the bandwidth allocated to its assigned group.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.dcb.priority-traffic-class"></a>priority-traffic-class</td>
<td align="left">array of uint32</td>
<td align="left">[0, 0, 0, 0, 0, 0, 0, 0]</td>
<td>An array of 8 uint values, where the array index corresponds to the User Priority (0 - 7) and the value indicates the traffic class (0 - 7) to which the priority is mapped.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.12"></a><h3>dummy setting</h3>
<p>Dummy Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody><tr>
<td align="left">
<a name="nm-settings.property.dummy.name"></a>name</td>
<td align="left">string</td>
<td align="left">dummy</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr></tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.13"></a><h3>generic setting</h3>
<p>Generic Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody><tr>
<td align="left">
<a name="nm-settings.property.generic.name"></a>name</td>
<td align="left">string</td>
<td align="left">generic</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr></tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.14"></a><h3>gsm setting</h3>
<p>GSM-based Mobile Broadband Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.apn"></a>apn</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The GPRS Access Point Name specifying the APN used when establishing a data session with the GSM-based network. The APN often determines how the user will be billed for their network usage and whether the user has access to the Internet or just a provider-specific walled-garden, so it is important to use the correct APN for the user's mobile broadband plan. The APN may only be composed of the characters a-z, 0-9, ., and - per GSM 03.60 Section 14.9.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.device-id"></a>device-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The device unique identifier (as given by the WWAN management service) which this connection applies to. If given, the connection will only apply to the specified device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.home-only"></a>home-only</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When TRUE, only connections to the home network will be allowed. Connections to roaming networks will not be made.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple frames.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.name"></a>name</td>
<td align="left">string</td>
<td align="left">gsm</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.network-id"></a>network-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The Network ID (GSM LAI format, ie MCC-MNC) to force specific network registration. If the Network ID is specified, NetworkManager will attempt to force the device to register only on the specified network. This can be used to ensure that the device does not roam when direct roaming control of the device is not otherwise possible.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.number"></a>number</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Number to dial when establishing a PPP data session with the GSM-based mobile broadband network. Many modems do not require PPP for connections to the mobile network and thus this property should be left blank, which allows NetworkManager to select the appropriate settings automatically.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.password"></a>password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The password used to authenticate with the network, if required. Many providers do not require a password, or accept any password. But if a password is required, it is specified here.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.password-flags"></a>password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.pin"></a>pin</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If the SIM is locked with a PIN it must be unlocked before any other operations are requested. Specify the PIN here to allow operation of the device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.pin-flags"></a>pin-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "pin" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.sim-id"></a>sim-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The SIM card unique identifier (as given by the WWAN management service) which this connection applies to. If given, the connection will apply to any device also allowed by "device-id" which contains a SIM card matching the given identifier.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.sim-operator-id"></a>sim-operator-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>A MCC/MNC string like "310260" or "21601" identifying the specific mobile network operator which this connection applies to. If given, the connection will apply to any device also allowed by "device-id" and "sim-id" which contains a SIM card provisioned by the given operator.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.gsm.username"></a>username</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The username used to authenticate with the network, if required. Many providers do not require a username, or accept any username. But if a username is required, it is specified here.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.15"></a><h3>infiniband setting</h3>
<p>Infiniband Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.mac-address"></a>mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, this connection will only apply to the IPoIB device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple frames.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.name"></a>name</td>
<td align="left">string</td>
<td align="left">infiniband</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.p-key"></a>p-key</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>The InfiniBand P_Key to use for this device. A value of -1 means to use the default P_Key (aka "the P_Key at index 0"). Otherwise it is a 16-bit unsigned integer, whose high bit is set if it is a "full membership" P_Key.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The interface name of the parent device of this device. Normally NULL, but if the "p_key" property is set, then you must specify the base device by setting either this property or "mac-address".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.infiniband.transport-mode"></a>transport-mode</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The IP-over-InfiniBand transport mode. Either "datagram" or "connected".</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.16"></a><h3>ipv4 setting</h3>
<p>IPv4 Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.address-data"></a>address-data</td>
<td align="left">array of vardict</td>
<td align="left"> </td>
<td>Array of IPv4 addresses. Each address dictionary contains at least 'address' and 'prefix' entries, containing the IP address as a string, and the prefix length as a uint32. Additional attributes may also exist on some addresses.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.addresses"></a>addresses</td>
<td align="left">array of array of uint32</td>
<td align="left">[]</td>
<td>Deprecated in favor of the 'address-data' and 'gateway' properties, but this can be used for backward-compatibility with older daemons. Note that if you send this property the daemon will ignore 'address-data' and 'gateway'. Array of IPv4 address structures. Each IPv4 address structure is composed of 3 32-bit values; the first being the IPv4 address (network byte order), the second the prefix (1 - 32), and last the IPv4 gateway (network byte order). The gateway may be left as 0 if no gateway exists for that subnet.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dad-timeout"></a>dad-timeout</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Timeout in milliseconds used to check for the presence of duplicate IP addresses on the network. If an address conflict is detected, the activation will fail. A zero value means that no duplicate address detection is performed, -1 means the default value (either configuration ipvx.dad-timeout override or 3 seconds). A value greater than zero is a timeout in milliseconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dhcp-client-id"></a>dhcp-client-id</td>
<td align="left">string</td>
<td align="left"> </td>
<td>A string sent to the DHCP server to identify the local machine which the DHCP server may use to customize the DHCP lease and options. When the property is a hex string ('aa:bb:cc') it is interpreted as a binary client ID, in which case the first byte is assumed to be the 'type' field as per RFC 2132 section 9.14 and the remaining bytes may be an hardware address (e.g. '01:xx:xx:xx:xx:xx:xx' where 1 is the Ethernet ARP type and the rest is a MAC address). If the property is not a hex string it is considered as a non-hardware-address client ID and the 'type' field is set to 0.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dhcp-fqdn"></a>dhcp-fqdn</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If the "dhcp-send-hostname" property is TRUE, then the specified FQDN will be sent to the DHCP server when acquiring a lease. This property and "dhcp-hostname" are mutually exclusive and cannot be set at the same time.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dhcp-hostname"></a>dhcp-hostname</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If the "dhcp-send-hostname" property is TRUE, then the specified name will be sent to the DHCP server when acquiring a lease. This property and "dhcp-fqdn" are mutually exclusive and cannot be set at the same time.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dhcp-send-hostname"></a>dhcp-send-hostname</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>If TRUE, a hostname is sent to the DHCP server when acquiring a lease. Some DHCP servers use this hostname to update DNS databases, essentially providing a static hostname for the computer. If the "dhcp-hostname" property is NULL and this property is TRUE, the current persistent hostname of the computer is sent.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dhcp-timeout"></a>dhcp-timeout</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>A timeout for a DHCP transaction in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dns"></a>dns</td>
<td align="left">array of uint32</td>
<td align="left">[]</td>
<td>Array of IP addresses of DNS servers (as network-byte-order integers)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dns-options"></a>dns-options</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Array of DNS options as described in man 5 resolv.conf. NULL means that the options are unset and left at the default. In this case NetworkManager will use default options. This is distinct from an empty list of properties.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dns-priority"></a>dns-priority</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Intra-connection DNS priority. The relative priority to be used when determining the order of DNS servers in resolv.conf. A lower value means that servers will be on top of the file. Zero selects the default value, which is 50 for VPNs and 100 for other connections. Note that the priority is to order DNS settings for multiple active connections. It does not disambiguate multiple DNS servers within the same connection profile. For that, just specify the DNS servers in the desired order. When multiple devices have configurations with the same priority, the one with an active default route will be preferred. Note that when using dns=dnsmasq the order is meaningless since dnsmasq forwards queries to all known servers at the same time. Negative values have the special effect of excluding other configurations with a greater priority value; so in presence of at least a negative priority, only DNS servers from connections with the lowest priority value will be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.dns-search"></a>dns-search</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Array of DNS search domains.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.gateway"></a>gateway</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The gateway associated with this configuration. This is only meaningful if "addresses" is also set.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.ignore-auto-dns"></a>ignore-auto-dns</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When "method" is set to "auto" and this property to TRUE, automatically configured nameservers and search domains are ignored and only nameservers and search domains specified in the "dns" and "dns-search" properties, if any, are used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.ignore-auto-routes"></a>ignore-auto-routes</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When "method" is set to "auto" and this property to TRUE, automatically configured routes are ignored and only routes specified in the "routes" property, if any, are used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.may-fail"></a>may-fail</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>If TRUE, allow overall network configuration to proceed even if the configuration specified by this property times out. Note that at least one IP configuration must succeed or overall network configuration will still fail. For example, in IPv6-only networks, setting this property to TRUE on the NMSettingIP4Config allows the overall network configuration to succeed if IPv4 configuration fails but IPv6 configuration completes successfully.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.method"></a>method</td>
<td align="left">string</td>
<td align="left"> </td>
<td>IP configuration method. NMSettingIP4Config and NMSettingIP6Config both support "auto", "manual", and "link-local". See the subclass-specific documentation for other values. In general, for the "auto" method, properties such as "dns" and "routes" specify information that is added on to the information returned from automatic configuration. The "ignore-auto-routes" and "ignore-auto-dns" properties modify this behavior. For methods that imply no upstream network, such as "shared" or "link-local", these properties must be empty. For IPv4 method "shared", the IP subnet can be configured by adding one manual IPv4 address or otherwise 10.42.x.0/24 is chosen.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.name"></a>name</td>
<td align="left">string</td>
<td align="left">ipv4</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.never-default"></a>never-default</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, this connection will never be the default connection for this IP type, meaning it will never be assigned the default route by NetworkManager.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.route-data"></a>route-data</td>
<td align="left">array of vardict</td>
<td align="left"> </td>
<td>Array of IPv4 routes. Each route dictionary contains at least 'dest' and 'prefix' entries, containing the destination IP address as a string, and the prefix length as a uint32. Most routes will also have a 'gateway' entry, containing the gateway IP address as a string. If the route has a 'metric' entry (containing a uint32), that will be used as the metric for the route (otherwise NM will pick a default value appropriate to the device). Additional attributes may also exist on some routes.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.route-metric"></a>route-metric</td>
<td align="left">int64</td>
<td align="left">-1</td>
<td>The default metric for routes that don't explicitly specify a metric. The default value -1 means that the metric is chosen automatically based on the device type. The metric applies to dynamic routes, manual (static) routes that don't have an explicit metric setting, address prefix routes, and the default route. Note that for IPv6, the kernel accepts zero (0) but coerces it to 1024 (user default). Hence, setting this property to zero effectively mean setting it to 1024. For IPv4, zero is a regular value for the metric.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.route-table"></a>route-table</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Enable policy routing (source routing) and set the routing table used when adding routes. This affects all routes, including device-routes, IPv4LL, DHCP, SLAAC, default-routes and static routes. But note that static routes can individually overwrite the setting by explicitly specifying a non-zero routing table. If the table setting is left at zero, it is eligible to be overwritten via global configuration. If the property is zero even after applying the global configuration value, policy routing is disabled for the address family of this connection. Policy routing disabled means that NetworkManager will add all routes to the main table (except static routes that explicitly configure a different table). Additionally, NetworkManager will not delete any extraneous routes from tables except the main table. This is to preserve backward compatibility for users who manage routing tables outside of NetworkManager.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv4.routes"></a>routes</td>
<td align="left">array of array of uint32</td>
<td align="left">[]</td>
<td>Deprecated in favor of the 'route-data' property, but this can be used for backward-compatibility with older daemons. Note that if you send this property the daemon will ignore 'route-data'. Array of IPv4 route structures. Each IPv4 route structure is composed of 4 32-bit values; the first being the destination IPv4 network or address (network byte order), the second the destination network or address prefix (1 - 32), the third being the next-hop (network byte order) if any, and the fourth being the route metric. If the metric is 0, NM will choose an appropriate default metric for the device. (There is no way to explicitly specify an actual metric of 0 with this property.)</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.17"></a><h3>ipv6 setting</h3>
<p>IPv6 Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.addr-gen-mode"></a>addr-gen-mode</td>
<td align="left">int32</td>
<td align="left">1</td>
<td>Configure method for creating the address for use with RFC4862 IPv6 Stateless Address Autoconfiguration. The permitted values are: NM_SETTING_IP6_CONFIG_ADDR_GEN_MODE_EUI64 (0) or NM_SETTING_IP6_CONFIG_ADDR_GEN_MODE_STABLE_PRIVACY (1). If the property is set to EUI64, the addresses will be generated using the interface tokens derived from hardware address. This makes the host part of the address to stay constant, making it possible to track host's presence when it changes networks. The address changes when the interface hardware is replaced. The value of stable-privacy enables use of cryptographically secure hash of a secret host-specific key along with the connection's stable-id and the network address as specified by RFC7217. This makes it impossible to use the address track host's presence, and makes the address stable when the network interface hardware is replaced. On D-Bus, the absence of an addr-gen-mode setting equals enabling stable-privacy. For keyfile plugin, the absence of the setting on disk means EUI64 so that the property doesn't change on upgrade from older versions. Note that this setting is distinct from the Privacy Extensions as configured by "ip6-privacy" property and it does not affect the temporary addresses configured with this option.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.address-data"></a>address-data</td>
<td align="left">array of vardict</td>
<td align="left"> </td>
<td>Array of IPv6 addresses. Each address dictionary contains at least 'address' and 'prefix' entries, containing the IP address as a string, and the prefix length as a uint32. Additional attributes may also exist on some addresses.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.addresses"></a>addresses</td>
<td align="left">array of legacy IPv6 address struct (a(ayuay))</td>
<td align="left">[]</td>
<td>Deprecated in favor of the 'address-data' and 'gateway' properties, but this can be used for backward-compatibility with older daemons. Note that if you send this property the daemon will ignore 'address-data' and 'gateway'. Array of IPv6 address structures. Each IPv6 address structure is composed of an IPv6 address, a prefix length (1 - 128), and an IPv6 gateway address. The gateway may be zeroed out if no gateway exists for that subnet.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dad-timeout"></a>dad-timeout</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Timeout in milliseconds used to check for the presence of duplicate IP addresses on the network. If an address conflict is detected, the activation will fail. A zero value means that no duplicate address detection is performed, -1 means the default value (either configuration ipvx.dad-timeout override or 3 seconds). A value greater than zero is a timeout in milliseconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dhcp-hostname"></a>dhcp-hostname</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If the "dhcp-send-hostname" property is TRUE, then the specified name will be sent to the DHCP server when acquiring a lease. This property and "dhcp-fqdn" are mutually exclusive and cannot be set at the same time.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dhcp-send-hostname"></a>dhcp-send-hostname</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>If TRUE, a hostname is sent to the DHCP server when acquiring a lease. Some DHCP servers use this hostname to update DNS databases, essentially providing a static hostname for the computer. If the "dhcp-hostname" property is NULL and this property is TRUE, the current persistent hostname of the computer is sent.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dhcp-timeout"></a>dhcp-timeout</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>A timeout for a DHCP transaction in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dns"></a>dns</td>
<td align="left">array of byte array</td>
<td align="left">[]</td>
<td>Array of IP addresses of DNS servers (in network byte order)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dns-options"></a>dns-options</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Array of DNS options as described in man 5 resolv.conf. NULL means that the options are unset and left at the default. In this case NetworkManager will use default options. This is distinct from an empty list of properties.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dns-priority"></a>dns-priority</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Intra-connection DNS priority. The relative priority to be used when determining the order of DNS servers in resolv.conf. A lower value means that servers will be on top of the file. Zero selects the default value, which is 50 for VPNs and 100 for other connections. Note that the priority is to order DNS settings for multiple active connections. It does not disambiguate multiple DNS servers within the same connection profile. For that, just specify the DNS servers in the desired order. When multiple devices have configurations with the same priority, the one with an active default route will be preferred. Note that when using dns=dnsmasq the order is meaningless since dnsmasq forwards queries to all known servers at the same time. Negative values have the special effect of excluding other configurations with a greater priority value; so in presence of at least a negative priority, only DNS servers from connections with the lowest priority value will be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.dns-search"></a>dns-search</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Array of DNS search domains.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.gateway"></a>gateway</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The gateway associated with this configuration. This is only meaningful if "addresses" is also set.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.ignore-auto-dns"></a>ignore-auto-dns</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When "method" is set to "auto" and this property to TRUE, automatically configured nameservers and search domains are ignored and only nameservers and search domains specified in the "dns" and "dns-search" properties, if any, are used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.ignore-auto-routes"></a>ignore-auto-routes</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>When "method" is set to "auto" and this property to TRUE, automatically configured routes are ignored and only routes specified in the "routes" property, if any, are used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.ip6-privacy"></a>ip6-privacy</td>
<td align="left">NMSettingIP6ConfigPrivacy (int32)</td>
<td align="left"> </td>
<td>Configure IPv6 Privacy Extensions for SLAAC, described in RFC4941. If enabled, it makes the kernel generate a temporary IPv6 address in addition to the public one generated from MAC address via modified EUI-64. This enhances privacy, but could cause problems in some applications, on the other hand. The permitted values are: -1: unknown, 0: disabled, 1: enabled (prefer public address), 2: enabled (prefer temporary addresses). Having a per-connection setting set to "-1" (unknown) means fallback to global configuration "ipv6.ip6-privacy". If also global configuration is unspecified or set to "-1", fallback to read "/proc/sys/net/ipv6/conf/default/use_tempaddr". Note that this setting is distinct from the Stable Privacy addresses that can be enabled with the "addr-gen-mode" property's "stable-privacy" setting as another way of avoiding host tracking with IPv6 addresses.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.may-fail"></a>may-fail</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>If TRUE, allow overall network configuration to proceed even if the configuration specified by this property times out. Note that at least one IP configuration must succeed or overall network configuration will still fail. For example, in IPv6-only networks, setting this property to TRUE on the NMSettingIP4Config allows the overall network configuration to succeed if IPv4 configuration fails but IPv6 configuration completes successfully.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.method"></a>method</td>
<td align="left">string</td>
<td align="left"> </td>
<td>IP configuration method. NMSettingIP4Config and NMSettingIP6Config both support "auto", "manual", and "link-local". See the subclass-specific documentation for other values. In general, for the "auto" method, properties such as "dns" and "routes" specify information that is added on to the information returned from automatic configuration. The "ignore-auto-routes" and "ignore-auto-dns" properties modify this behavior. For methods that imply no upstream network, such as "shared" or "link-local", these properties must be empty. For IPv4 method "shared", the IP subnet can be configured by adding one manual IPv4 address or otherwise 10.42.x.0/24 is chosen.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.name"></a>name</td>
<td align="left">string</td>
<td align="left">ipv6</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.never-default"></a>never-default</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, this connection will never be the default connection for this IP type, meaning it will never be assigned the default route by NetworkManager.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.route-data"></a>route-data</td>
<td align="left">array of vardict</td>
<td align="left"> </td>
<td>Array of IPv6 routes. Each route dictionary contains at least 'dest' and 'prefix' entries, containing the destination IP address as a string, and the prefix length as a uint32. Most routes will also have a 'next-hop' entry, containing the next hop IP address as a string. If the route has a 'metric' entry (containing a uint32), that will be used as the metric for the route (otherwise NM will pick a default value appropriate to the device). Additional attributes may also exist on some routes.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.route-metric"></a>route-metric</td>
<td align="left">int64</td>
<td align="left">-1</td>
<td>The default metric for routes that don't explicitly specify a metric. The default value -1 means that the metric is chosen automatically based on the device type. The metric applies to dynamic routes, manual (static) routes that don't have an explicit metric setting, address prefix routes, and the default route. Note that for IPv6, the kernel accepts zero (0) but coerces it to 1024 (user default). Hence, setting this property to zero effectively mean setting it to 1024. For IPv4, zero is a regular value for the metric.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.route-table"></a>route-table</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Enable policy routing (source routing) and set the routing table used when adding routes. This affects all routes, including device-routes, IPv4LL, DHCP, SLAAC, default-routes and static routes. But note that static routes can individually overwrite the setting by explicitly specifying a non-zero routing table. If the table setting is left at zero, it is eligible to be overwritten via global configuration. If the property is zero even after applying the global configuration value, policy routing is disabled for the address family of this connection. Policy routing disabled means that NetworkManager will add all routes to the main table (except static routes that explicitly configure a different table). Additionally, NetworkManager will not delete any extraneous routes from tables except the main table. This is to preserve backward compatibility for users who manage routing tables outside of NetworkManager.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.routes"></a>routes</td>
<td align="left">array of legacy IPv6 route struct (a(ayuayu))</td>
<td align="left">[]</td>
<td>Deprecated in favor of the 'route-data' property, but this can be used for backward-compatibility with older daemons. Note that if you send this property the daemon will ignore 'route-data'. Array of IPv6 route structures. Each IPv6 route structure is composed of an IPv6 address, a prefix length (1 - 128), an IPv6 next hop address (which may be zeroed out if there is no next hop), and a metric. If the metric is 0, NM will choose an appropriate default metric for the device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ipv6.token"></a>token</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Configure the token for draft-chown-6man-tokenised-ipv6-identifiers-02 IPv6 tokenized interface identifiers. Useful with eui64 addr-gen-mode.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.18"></a><h3>ip-tunnel setting</h3>
<p>IP Tunneling Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.encapsulation-limit"></a>encapsulation-limit</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>How many additional levels of encapsulation are permitted to be prepended to packets. This property applies only to IPv6 tunnels.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.flow-label"></a>flow-label</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The flow label to assign to tunnel packets. This property applies only to IPv6 tunnels.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.input-key"></a>input-key</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The key used for tunnel input packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.local"></a>local</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The local endpoint of the tunnel; the value can be empty, otherwise it must contain an IPv4 or IPv6 address.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.mode"></a>mode</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The tunneling mode, for example NM_IP_TUNNEL_MODE_IPIP (1) or NM_IP_TUNNEL_MODE_GRE (2).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple fragments.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.name"></a>name</td>
<td align="left">string</td>
<td align="left">ip-tunnel</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.output-key"></a>output-key</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The key used for tunnel output packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name or parent connection UUID the new device will be bound to so that tunneled packets will only be routed via that interface.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.path-mtu-discovery"></a>path-mtu-discovery</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Whether to enable Path MTU Discovery on this tunnel.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.remote"></a>remote</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The remote endpoint of the tunnel; the value must contain an IPv4 or IPv6 address.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.tos"></a>tos</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The type of service (IPv4) or traffic class (IPv6) field to be set on tunneled packets.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ip-tunnel.ttl"></a>ttl</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The TTL to assign to tunneled packets. 0 is a special value meaning that packets inherit the TTL value.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.19"></a><h3>macsec setting</h3>
<p>MACSec Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.encrypt"></a>encrypt</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Whether the transmitted traffic must be encrypted.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.mka-cak"></a>mka-cak</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The pre-shared CAK (Connectivity Association Key) for MACsec Key Agreement.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.mka-cak-flags"></a>mka-cak-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "mka-cak" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.mka-ckn"></a>mka-ckn</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The pre-shared CKN (Connectivity-association Key Name) for MACsec Key Agreement.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.mode"></a>mode</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Specifies how the CAK (Connectivity Association Key) for MKA (MACsec Key Agreement) is obtained.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.name"></a>name</td>
<td align="left">string</td>
<td align="left">macsec</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name or parent connection UUID from which this MACSEC interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.port"></a>port</td>
<td align="left">int32</td>
<td align="left">1</td>
<td>The port component of the SCI (Secure Channel Identifier), between 1 and 65534.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macsec.validation"></a>validation</td>
<td align="left">int32</td>
<td align="left">2</td>
<td>Specifies the validation mode for incoming frames.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.20"></a><h3>macvlan setting</h3>
<p>MAC VLAN Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.macvlan.mode"></a>mode</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The macvlan mode, which specifies the communication mechanism between multiple macvlans on the same lower device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macvlan.name"></a>name</td>
<td align="left">string</td>
<td align="left">macvlan</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macvlan.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name or parent connection UUID from which this MAC-VLAN interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macvlan.promiscuous"></a>promiscuous</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Whether the interface should be put in promiscuous mode.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.macvlan.tap"></a>tap</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Whether the interface should be a MACVTAP.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.21"></a><h3>802-11-olpc-mesh setting</h3>
<p>OLPC Wireless Mesh Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-olpc-mesh.channel"></a>channel</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Channel on which the mesh network to join is located.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-olpc-mesh.dhcp-anycast-address"></a>dhcp-anycast-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>Anycast DHCP MAC address used when requesting an IP address via DHCP. The specific anycast address used determines which DHCP server class answers the request.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-olpc-mesh.name"></a>name</td>
<td align="left">string</td>
<td align="left">802-11-olpc-mesh</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-olpc-mesh.ssid"></a>ssid</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>SSID of the mesh network to join.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.22"></a><h3>ovs-bridge setting</h3>
<p>OvsBridge Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-bridge.fail-mode"></a>fail-mode</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The bridge failure mode. One of "secure", "standalone" or empty.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-bridge.mcast-snooping-enable"></a>mcast-snooping-enable</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Enable or disable multicast snooping.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-bridge.name"></a>name</td>
<td align="left">string</td>
<td align="left">ovs-bridge</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-bridge.rstp-enable"></a>rstp-enable</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Enable or disable RSTP.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-bridge.stp-enable"></a>stp-enable</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Enable or disable STP.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.23"></a><h3>ovs-interface setting</h3>
<p>OpenVSwitch Interface Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-interface.name"></a>name</td>
<td align="left">string</td>
<td align="left">ovs-interface</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-interface.type"></a>type</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The interface type. Either "internal", or empty.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.24"></a><h3>ovs-patch setting</h3>
<p>OvsPatch Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-patch.name"></a>name</td>
<td align="left">string</td>
<td align="left">ovs-patch</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-patch.peer"></a>peer</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Specifies the unicast destination IP address of a remote OpenVSwitch bridge port to connect to.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.25"></a><h3>ovs-port setting</h3>
<p>OvsPort Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.bond-downdelay"></a>bond-downdelay</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The time port must be inactive in order to be considered down.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.bond-mode"></a>bond-mode</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Bonding mode. One of "active-backup", "balance-slb", or "balance-tcp".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.bond-updelay"></a>bond-updelay</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The time port must be active before it starts forwarding traffic.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.lacp"></a>lacp</td>
<td align="left">string</td>
<td align="left"> </td>
<td>LACP mode. One of "active", "off", or "passive".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.name"></a>name</td>
<td align="left">string</td>
<td align="left">ovs-port</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.tag"></a>tag</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The VLAN tag in the range 0-4095.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ovs-port.vlan-mode"></a>vlan-mode</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The VLAN mode. One of "access", "native-tagged", "native-untagged", "trunk" or unset.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.26"></a><h3>ppp setting</h3>
<p>Point-to-Point Protocol Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.baud"></a>baud</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, instruct pppd to set the serial port to the specified baudrate. This value should normally be left as 0 to automatically choose the speed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.crtscts"></a>crtscts</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, specify that pppd should set the serial port to use hardware flow control with RTS and CTS signals. This value should normally be set to FALSE.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.lcp-echo-failure"></a>lcp-echo-failure</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, instruct pppd to presume the connection to the peer has failed if the specified number of LCP echo-requests go unanswered by the peer. The "lcp-echo-interval" property must also be set to a non-zero value if this property is used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.lcp-echo-interval"></a>lcp-echo-interval</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, instruct pppd to send an LCP echo-request frame to the peer every n seconds (where n is the specified value). Note that some PPP peers will respond to echo requests and some will not, and it is not possible to autodetect this.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.mppe-stateful"></a>mppe-stateful</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, stateful MPPE is used. See pppd documentation for more information on stateful MPPE.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.mru"></a>mru</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, instruct pppd to request that the peer send packets no larger than the specified size. If non-zero, the MRU should be between 128 and 16384.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, instruct pppd to send packets no larger than the specified size.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.name"></a>name</td>
<td align="left">string</td>
<td align="left">ppp</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.no-vj-comp"></a>no-vj-comp</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, Van Jacobsen TCP header compression will not be requested.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.noauth"></a>noauth</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>If TRUE, do not require the other side (usually the PPP server) to authenticate itself to the client. If FALSE, require authentication from the remote side. In almost all cases, this should be TRUE.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.nobsdcomp"></a>nobsdcomp</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, BSD compression will not be requested.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.nodeflate"></a>nodeflate</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, "deflate" compression will not be requested.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.refuse-chap"></a>refuse-chap</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, the CHAP authentication method will not be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.refuse-eap"></a>refuse-eap</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, the EAP authentication method will not be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.refuse-mschap"></a>refuse-mschap</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, the MSCHAP authentication method will not be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.refuse-mschapv2"></a>refuse-mschapv2</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, the MSCHAPv2 authentication method will not be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.refuse-pap"></a>refuse-pap</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, the PAP authentication method will not be used.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.require-mppe"></a>require-mppe</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, MPPE (Microsoft Point-to-Point Encryption) will be required for the PPP session. If either 64-bit or 128-bit MPPE is not available the session will fail. Note that MPPE is not used on mobile broadband connections.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.ppp.require-mppe-128"></a>require-mppe-128</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, 128-bit MPPE (Microsoft Point-to-Point Encryption) will be required for the PPP session, and the "require-mppe" property must also be set to TRUE. If 128-bit MPPE is not available the session will fail.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.27"></a><h3>pppoe setting</h3>
<p>PPP-over-Ethernet Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.name"></a>name</td>
<td align="left">string</td>
<td align="left">pppoe</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name on which this PPPoE connection should be created. If this property is not specified, the connection is activated on the interface specified in "interface-name" of NMSettingConnection.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.password"></a>password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Password used to authenticate with the PPPoE service.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.password-flags"></a>password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.service"></a>service</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If specified, instruct PPPoE to only initiate sessions with access concentrators that provide the specified service. For most providers, this should be left blank. It is only required if there are multiple access concentrators or a specific service is known to be required.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.pppoe.username"></a>username</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Username used to authenticate with the PPPoE service.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.28"></a><h3>proxy setting</h3>
<p>WWW Proxy Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.proxy.browser-only"></a>browser-only</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Whether the proxy configuration is for browser only.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.proxy.method"></a>method</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Method for proxy configuration, Default is NM_SETTING_PROXY_METHOD_NONE (0)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.proxy.name"></a>name</td>
<td align="left">string</td>
<td align="left">proxy</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.proxy.pac-script"></a>pac-script</td>
<td align="left">string</td>
<td align="left"> </td>
<td>PAC script for the connection.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.proxy.pac-url"></a>pac-url</td>
<td align="left">string</td>
<td align="left"> </td>
<td>PAC URL for obtaining PAC file.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.29"></a><h3>serial setting</h3>
<p>Serial Link Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.serial.baud"></a>baud</td>
<td align="left">uint32</td>
<td align="left">57600</td>
<td>Speed to use for communication over the serial port. Note that this value usually has no effect for mobile broadband modems as they generally ignore speed settings and use the highest available speed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.serial.bits"></a>bits</td>
<td align="left">uint32</td>
<td align="left">8</td>
<td>Byte-width of the serial communication. The 8 in "8n1" for example.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.serial.name"></a>name</td>
<td align="left">string</td>
<td align="left">serial</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.serial.parity"></a>parity</td>
<td align="left">byte</td>
<td align="left"> </td>
<td>The connection parity: 69 (ASCII 'E') for even parity, 111 (ASCII 'o') for odd, 110 (ASCII 'n') for none.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.serial.send-delay"></a>send-delay</td>
<td align="left">uint64</td>
<td align="left">0</td>
<td>Time to delay between each byte sent to the modem, in microseconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.serial.stopbits"></a>stopbits</td>
<td align="left">uint32</td>
<td align="left">1</td>
<td>Number of stop bits for communication on the serial port. Either 1 or 2. The 1 in "8n1" for example.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.30"></a><h3>tc setting</h3>
<p>Linux Traffic Contril Settings..</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.tc.name"></a>name</td>
<td align="left">string</td>
<td align="left">tc</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tc.qdiscs"></a>qdiscs</td>
<td align="left">array of vardict</td>
<td align="left">[]</td>
<td>Array of TC queuening disciplines.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tc.tfilters"></a>tfilters</td>
<td align="left">array of vardict</td>
<td align="left">[]</td>
<td>Array of TC traffic filters.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.31"></a><h3>team setting</h3>
<p>Teaming Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.team.config"></a>config</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The JSON configuration for the team network interface. The property should contain raw JSON configuration data suitable for teamd, because the value is passed directly to teamd. If not specified, the default configuration is used. See man teamd.conf for the format details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.interface-name"></a>interface-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Deprecated in favor of connection.interface-name, but can be used for backward-compatibility with older daemons, to set the team's interface name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.link-watchers"></a>link-watchers</td>
<td align="left">array of vardict</td>
<td align="left">[]</td>
<td>Link watchers configuration for the connection: each link watcher is defined by a dictionary, whose keys depend upon the selected link watcher. Available link watchers are 'ethtool', 'nsna_ping' and 'arp_ping' and it is specified in the dictionary with the key 'name'. Available keys are: ethtool: 'delay-up', 'delay-down', 'init-wait'; nsna_ping: 'init-wait', 'interval', 'missed-max', 'target-host'; arp_ping: all the ones in nsna_ping and 'source-host', 'validate-active', 'validate-incative', 'send-always'. See teamd.conf man for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.mcast-rejoin-count"></a>mcast-rejoin-count</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd mcast_rejoin.count.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.mcast-rejoin-interval"></a>mcast-rejoin-interval</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd mcast_rejoin.interval.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.name"></a>name</td>
<td align="left">string</td>
<td align="left">team</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.notify-peers-count"></a>notify-peers-count</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd notify_peers.count.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.notify-peers-interval"></a>notify-peers-interval</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd notify_peers.interval.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner"></a>runner</td>
<td align="left">string</td>
<td align="left">"roundrobin"</td>
<td>Corresponds to the teamd runner.name. Permitted values are: "roundrobin", "broadcast", "activebackup", "loadbalance", "lacp". When setting the runner, all the properties specific to the runner will be reset to the default value; all the properties specific to other runners will be set to an empty value (or if not possible to a default value).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-active"></a>runner-active</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Corresponds to the teamd runner.active.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-agg-select-policy"></a>runner-agg-select-policy</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Corresponds to the teamd runner.agg_select_policy.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-fast-rate"></a>runner-fast-rate</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Corresponds to the teamd runner.fast_rate.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-hwaddr-policy"></a>runner-hwaddr-policy</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Corresponds to the teamd runner.hwaddr_policy.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-min-ports"></a>runner-min-ports</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Corresponds to the teamd runner.min_ports.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-sys-prio"></a>runner-sys-prio</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Corresponds to the teamd runner.sys_prio.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-tx-balancer"></a>runner-tx-balancer</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Corresponds to the teamd runner.tx_balancer.name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-tx-balancer-interval"></a>runner-tx-balancer-interval</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Corresponds to the teamd runner.tx_balancer.interval.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team.runner-tx-hash"></a>runner-tx-hash</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Corresponds to the teamd runner.tx_hash.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.32"></a><h3>team-port setting</h3>
<p>Team Port Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.config"></a>config</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The JSON configuration for the team port. The property should contain raw JSON configuration data suitable for teamd, because the value is passed directly to teamd. If not specified, the default configuration is used. See man teamd.conf for the format details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.lacp-key"></a>lacp-key</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd ports.PORTIFNAME.lacp_key.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.lacp-prio"></a>lacp-prio</td>
<td align="left">int32</td>
<td align="left">255</td>
<td>Corresponds to the teamd ports.PORTIFNAME.lacp_prio.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.link-watchers"></a>link-watchers</td>
<td align="left">array of vardict</td>
<td align="left">[]</td>
<td>Link watchers configuration for the connection: each link watcher is defined by a dictionary, whose keys depend upon the selected link watcher. Available link watchers are 'ethtool', 'nsna_ping' and 'arp_ping' and it is specified in the dictionary with the key 'name'. Available keys are: ethtool: 'delay-up', 'delay-down', 'init-wait'; nsna_ping: 'init-wait', 'interval', 'missed-max', 'target-host'; arp_ping: all the ones in nsna_ping and 'source-host', 'validate-active', 'validate-incative', 'send-always'. See teamd.conf man for more details.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.name"></a>name</td>
<td align="left">string</td>
<td align="left">team-port</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.prio"></a>prio</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Corresponds to the teamd ports.PORTIFNAME.prio.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.queue-id"></a>queue-id</td>
<td align="left">int32</td>
<td align="left">-1</td>
<td>Corresponds to the teamd ports.PORTIFNAME.queue_id. When set to -1 means the parameter is skipped from the json config.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.team-port.sticky"></a>sticky</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Corresponds to the teamd ports.PORTIFNAME.sticky.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.33"></a><h3>tun setting</h3>
<p>Tunnel Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.tun.group"></a>group</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The group ID which will own the device. If set to NULL everyone will be able to use the device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.mode"></a>mode</td>
<td align="left">uint32</td>
<td align="left">1</td>
<td>The operating mode of the virtual device. Allowed values are NM_SETTING_TUN_MODE_TUN (1) to create a layer 3 device and NM_SETTING_TUN_MODE_TAP (2) to create an Ethernet-like layer 2 one.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.multi-queue"></a>multi-queue</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If the property is set to TRUE, the interface will support multiple file descriptors (queues) to parallelize packet sending or receiving. Otherwise, the interface will only support a single queue.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.name"></a>name</td>
<td align="left">string</td>
<td align="left">tun</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.owner"></a>owner</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The user ID which will own the device. If set to NULL everyone will be able to use the device.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.pi"></a>pi</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE the interface will prepend a 4 byte header describing the physical interface to the packets.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.tun.vnet-hdr"></a>vnet-hdr</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE the IFF_VNET_HDR the tunnel packets will include a virtio network header.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.34"></a><h3>user setting</h3>
<p>General User Profile Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.user.data"></a>data</td>
<td align="left">dict of string to string</td>
<td align="left">{}</td>
<td>A dictionary of key/value pairs with user data. This data is ignored by NetworkManager and can be used at the users discretion. The keys only support a strict ascii format, but the values can be arbitrary UTF8 strings up to a certain length.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.user.name"></a>name</td>
<td align="left">string</td>
<td align="left">user</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.35"></a><h3>vlan setting</h3>
<p>VLAN Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.egress-priority-map"></a>egress-priority-map</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>For outgoing packets, a list of mappings from Linux SKB priorities to 802.1p priorities. The mapping is given in the format "from:to" where both "from" and "to" are unsigned integers, ie "7:3".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.flags"></a>flags</td>
<td align="left">NMVlanFlags (uint32)</td>
<td align="left"> </td>
<td>One or more flags which control the behavior and features of the VLAN interface. Flags include NM_VLAN_FLAG_REORDER_HEADERS (0x1) (reordering of output packet headers), NM_VLAN_FLAG_GVRP (0x2) (use of the GVRP protocol), and NM_VLAN_FLAG_LOOSE_BINDING (0x4) (loose binding of the interface to its master device's operating state). NM_VLAN_FLAG_MVRP (0x8) (use of the MVRP protocol). The default value of this property is NM_VLAN_FLAG_REORDER_HEADERS, but it used to be 0. To preserve backward compatibility, the default-value in the D-Bus API continues to be 0 and a missing property on D-Bus is still considered as 0.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.id"></a>id</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>The VLAN identifier that the interface created by this connection should be assigned. The valid range is from 0 to 4094, without the reserved id 4095.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.ingress-priority-map"></a>ingress-priority-map</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>For incoming packets, a list of mappings from 802.1p priorities to Linux SKB priorities. The mapping is given in the format "from:to" where both "from" and "to" are unsigned integers, ie "7:3".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.interface-name"></a>interface-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Deprecated in favor of connection.interface-name, but can be used for backward-compatibility with older daemons, to set the vlan's interface name.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.name"></a>name</td>
<td align="left">string</td>
<td align="left">vlan</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vlan.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name or parent connection UUID from which this VLAN interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.36"></a><h3>vpn setting</h3>
<p>VPN Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.data"></a>data</td>
<td align="left">dict of string to string</td>
<td align="left">{}</td>
<td>Dictionary of key/value pairs of VPN plugin specific data. Both keys and values must be strings.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.name"></a>name</td>
<td align="left">string</td>
<td align="left">vpn</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.persistent"></a>persistent</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If the VPN service supports persistence, and this property is TRUE, the VPN will attempt to stay connected across link changes and outages, until explicitly disconnected.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.secrets"></a>secrets</td>
<td align="left">dict of string to string</td>
<td align="left">{}</td>
<td>Dictionary of key/value pairs of VPN plugin specific secrets like passwords or private keys. Both keys and values must be strings.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.service-type"></a>service-type</td>
<td align="left">string</td>
<td align="left"> </td>
<td>D-Bus service name of the VPN plugin that this setting uses to connect to its network. i.e. org.freedesktop.NetworkManager.vpnc for the vpnc plugin.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.timeout"></a>timeout</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Timeout for the VPN service to establish the connection. Some services may take quite a long time to connect. Value of 0 means a default timeout, which is 60 seconds (unless overridden by vpn.timeout in configuration file). Values greater than zero mean timeout in seconds.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vpn.user-name"></a>user-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If the VPN connection requires a user name for authentication, that name should be provided here. If the connection is available to more than one user, and the VPN requires each user to supply a different name, then leave this property empty. If this property is empty, NetworkManager will automatically supply the username of the user which requested the VPN connection.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.37"></a><h3>vxlan setting</h3>
<p>VXLAN Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.ageing"></a>ageing</td>
<td align="left">uint32</td>
<td align="left">300</td>
<td>Specifies the lifetime in seconds of FDB entries learnt by the kernel.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.destination-port"></a>destination-port</td>
<td align="left">uint32</td>
<td align="left">8472</td>
<td>Specifies the UDP destination port to communicate to the remote VXLAN tunnel endpoint.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.id"></a>id</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the VXLAN Network Identifier (or VXLAN Segment Identifier) to use.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.l2-miss"></a>l2-miss</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Specifies whether netlink LL ADDR miss notifications are generated.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.l3-miss"></a>l3-miss</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Specifies whether netlink IP ADDR miss notifications are generated.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.learning"></a>learning</td>
<td align="left">boolean</td>
<td align="left">TRUE</td>
<td>Specifies whether unknown source link layer addresses and IP addresses are entered into the VXLAN device forwarding database.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.limit"></a>limit</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the maximum number of FDB entries. A value of zero means that the kernel will store unlimited entries.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.local"></a>local</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the source IP address to use in outgoing packets.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.name"></a>name</td>
<td align="left">string</td>
<td align="left">vxlan</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.parent"></a>parent</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If given, specifies the parent interface name or parent connection UUID.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.proxy"></a>proxy</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Specifies whether ARP proxy is turned on.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.remote"></a>remote</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Specifies the unicast destination IP address to use in outgoing packets when the destination link layer address is not known in the VXLAN device forwarding database, or the multicast IP address to join.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.rsc"></a>rsc</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>Specifies whether route short circuit is turned on.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.source-port-max"></a>source-port-max</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the maximum UDP source port to communicate to the remote VXLAN tunnel endpoint.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.source-port-min"></a>source-port-min</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the minimum UDP source port to communicate to the remote VXLAN tunnel endpoint.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.tos"></a>tos</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the TOS value to use in outgoing packets.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.vxlan.ttl"></a>ttl</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Specifies the time-to-live value to use in outgoing packets.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.38"></a><h3>wimax setting</h3>
<p>WiMax Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.wimax.mac-address"></a>mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, this connection will only apply to the WiMAX device whose MAC address matches. This property does not change the MAC address of the device (known as MAC spoofing). Deprecated: 1</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.wimax.name"></a>name</td>
<td align="left">string</td>
<td align="left">wimax</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.wimax.network-name"></a>network-name</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Network Service Provider (NSP) name of the WiMAX network this connection should use. Deprecated: 1</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.39"></a><h3>802-3-ethernet setting</h3>
<p>Wired Ethernet Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.assigned-mac-address"></a>assigned-mac-address</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The new field for the cloned MAC address. It can be either a hardware address in ASCII representation, or one of the special values "preserve", "permanent", "random" or "stable". This field replaces the deprecated "cloned-mac-address" on D-Bus, which can only contain explict hardware addresses. Note that this property only exists in D-Bus API. libnm and nmcli continue to call this property "cloned-mac-address".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.auto-negotiate"></a>auto-negotiate</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, enforce auto-negotiation of port speed and duplex mode. If FALSE, "speed" and "duplex" properties should be both set or link configuration will be skipped.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.cloned-mac-address"></a>cloned-mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>This D-Bus field is deprecated in favor of "assigned-mac-address" which is more flexible and allows specifying special variants like "random". For libnm and nmcli, this field is called "cloned-mac-address".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.duplex"></a>duplex</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Can be specified only when "auto-negotiate" is "off". In that case, statically configures the device to use that specified duplex mode, either "half" or "full". Must be set together with the "speed" property if specified. Before specifying a duplex mode be sure your device supports it.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.generate-mac-address-mask"></a>generate-mac-address-mask</td>
<td align="left">string</td>
<td align="left"> </td>
<td>With "cloned-mac-address" setting "random" or "stable", by default all bits of the MAC address are scrambled and a locally-administered, unicast MAC address is created. This property allows to specify that certain bits are fixed. Note that the least significant bit of the first MAC address will always be unset to create a unicast MAC address. If the property is NULL, it is eligible to be overwritten by a default connection setting. If the value is still NULL or an empty string, the default is to create a locally-administered, unicast MAC address. If the value contains one MAC address, this address is used as mask. The set bits of the mask are to be filled with the current MAC address of the device, while the unset bits are subject to randomization. Setting "FE:FF:FF:00:00:00" means to preserve the OUI of the current MAC address and only randomize the lower 3 bytes using the "random" or "stable" algorithm. If the value contains one additional MAC address after the mask, this address is used instead of the current MAC address to fill the bits that shall not be randomized. For example, a value of "FE:FF:FF:00:00:00 68:F7:28:00:00:00" will set the OUI of the MAC address to 68:F7:28, while the lower bits are randomized. A value of "02:00:00:00:00:00 00:00:00:00:00:00" will create a fully scrambled globally-administered, burned-in MAC address. If the value contains more than one additional MAC addresses, one of them is chosen randomly. For example, "02:00:00:00:00:00 00:00:00:00:00:00 02:00:00:00:00:00" will create a fully scrambled MAC address, randomly locally or globally administered.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.mac-address"></a>mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, this connection will only apply to the Ethernet device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.mac-address-blacklist"></a>mac-address-blacklist</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>If specified, this connection will never apply to the Ethernet device whose permanent MAC address matches an address in the list. Each MAC address is in the standard hex-digits-and-colons notation (00:11:22:33:44:55).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple Ethernet frames.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.name"></a>name</td>
<td align="left">string</td>
<td align="left">802-3-ethernet</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.port"></a>port</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Specific port type to use if the device supports multiple attachment methods. One of "tp" (Twisted Pair), "aui" (Attachment Unit Interface), "bnc" (Thin Ethernet) or "mii" (Media Independent Interface). If the device supports only one port type, this setting is ignored.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.s390-nettype"></a>s390-nettype</td>
<td align="left">string</td>
<td align="left"> </td>
<td>s390 network device type; one of "qeth", "lcs", or "ctc", representing the different types of virtual network devices available on s390 systems.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.s390-options"></a>s390-options</td>
<td align="left">dict of string to string</td>
<td align="left">{}</td>
<td>Dictionary of key/value pairs of s390-specific device options. Both keys and values must be strings. Allowed keys include "portno", "layer2", "portname", "protocol", among others. Key names must contain only alphanumeric characters (ie, [a-zA-Z0-9]).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.s390-subchannels"></a>s390-subchannels</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>Identifies specific subchannels that this network device uses for communication with z/VM or s390 host. Like the "mac-address" property for non-z/VM devices, this property can be used to ensure this connection only applies to the network device that uses these subchannels. The list should contain exactly 3 strings, and each string may only be composed of hexadecimal characters and the period (.) character.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.speed"></a>speed</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Can be set to a value greater than zero only when "auto-negotiate" is "off". In that case, statically configures the device to use that specified speed. In Mbit/s, ie 100 == 100Mbit/s. Must be set together with the "duplex" property when non-zero. Before specifying a speed value be sure your device supports it.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.wake-on-lan"></a>wake-on-lan</td>
<td align="left">uint32</td>
<td align="left">1</td>
<td>The NMSettingWiredWakeOnLan options to enable. Not all devices support all options. May be any combination of NM_SETTING_WIRED_WAKE_ON_LAN_PHY (0x2), NM_SETTING_WIRED_WAKE_ON_LAN_UNICAST (0x4), NM_SETTING_WIRED_WAKE_ON_LAN_MULTICAST (0x8), NM_SETTING_WIRED_WAKE_ON_LAN_BROADCAST (0x10), NM_SETTING_WIRED_WAKE_ON_LAN_ARP (0x20), NM_SETTING_WIRED_WAKE_ON_LAN_MAGIC (0x40) or the special values NM_SETTING_WIRED_WAKE_ON_LAN_DEFAULT (0x1) (to use global settings) and NM_SETTING_WIRED_WAKE_ON_LAN_IGNORE (0x8000) (to disable management of Wake-on-LAN in NetworkManager).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-3-ethernet.wake-on-lan-password"></a>wake-on-lan-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>If specified, the password used with magic-packet-based Wake-on-LAN, represented as an Ethernet MAC address. If NULL, no password will be required.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.40"></a><h3>802-11-wireless setting</h3>
<p>Wi-Fi Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.assigned-mac-address"></a>assigned-mac-address</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The new field for the cloned MAC address. It can be either a hardware address in ASCII representation, or one of the special values "preserve", "permanent", "random" or "stable". This field replaces the deprecated "cloned-mac-address" on D-Bus, which can only contain explict hardware addresses. Note that this property only exists in D-Bus API. libnm and nmcli continue to call this property "cloned-mac-address".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.band"></a>band</td>
<td align="left">string</td>
<td align="left"> </td>
<td>802.11 frequency band of the network. One of "a" for 5GHz 802.11a or "bg" for 2.4GHz 802.11. This will lock associations to the Wi-Fi network to the specific band, i.e. if "a" is specified, the device will not associate with the same network in the 2.4GHz band even if the network's settings are compatible. This setting depends on specific driver capability and may not work with all drivers.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.bssid"></a>bssid</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, directs the device to only associate with the given access point. This capability is highly driver dependent and not supported by all devices. Note: this property does not control the BSSID used when creating an Ad-Hoc network and is unlikely to in the future.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.channel"></a>channel</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Wireless channel to use for the Wi-Fi connection. The device will only join (or create for Ad-Hoc networks) a Wi-Fi network on the specified channel. Because channel numbers overlap between bands, this property also requires the "band" property to be set.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.cloned-mac-address"></a>cloned-mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>This D-Bus field is deprecated in favor of "assigned-mac-address" which is more flexible and allows specifying special variants like "random". For libnm and nmcli, this field is called "cloned-mac-address".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.generate-mac-address-mask"></a>generate-mac-address-mask</td>
<td align="left">string</td>
<td align="left"> </td>
<td>With "cloned-mac-address" setting "random" or "stable", by default all bits of the MAC address are scrambled and a locally-administered, unicast MAC address is created. This property allows to specify that certain bits are fixed. Note that the least significant bit of the first MAC address will always be unset to create a unicast MAC address. If the property is NULL, it is eligible to be overwritten by a default connection setting. If the value is still NULL or an empty string, the default is to create a locally-administered, unicast MAC address. If the value contains one MAC address, this address is used as mask. The set bits of the mask are to be filled with the current MAC address of the device, while the unset bits are subject to randomization. Setting "FE:FF:FF:00:00:00" means to preserve the OUI of the current MAC address and only randomize the lower 3 bytes using the "random" or "stable" algorithm. If the value contains one additional MAC address after the mask, this address is used instead of the current MAC address to fill the bits that shall not be randomized. For example, a value of "FE:FF:FF:00:00:00 68:F7:28:00:00:00" will set the OUI of the MAC address to 68:F7:28, while the lower bits are randomized. A value of "02:00:00:00:00:00 00:00:00:00:00:00" will create a fully scrambled globally-administered, burned-in MAC address. If the value contains more than one additional MAC addresses, one of them is chosen randomly. For example, "02:00:00:00:00:00 00:00:00:00:00:00 02:00:00:00:00:00" will create a fully scrambled MAC address, randomly locally or globally administered.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.hidden"></a>hidden</td>
<td align="left">boolean</td>
<td align="left">FALSE</td>
<td>If TRUE, indicates this network is a non-broadcasting network that hides its SSID. In this case various workarounds may take place, such as probe-scanning the SSID for more reliable network discovery. However, these workarounds expose inherent insecurities with hidden SSID networks, and thus hidden SSID networks should be used with caution.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.mac-address"></a>mac-address</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>If specified, this connection will only apply to the Wi-Fi device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.mac-address-blacklist"></a>mac-address-blacklist</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>A list of permanent MAC addresses of Wi-Fi devices to which this connection should never apply. Each MAC address should be given in the standard hex-digits-and-colons notation (eg "00:11:22:33:44:55").</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.mac-address-randomization"></a>mac-address-randomization</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>One of NM_SETTING_MAC_RANDOMIZATION_DEFAULT (0) (never randomize unless the user has set a global default to randomize and the supplicant supports randomization), NM_SETTING_MAC_RANDOMIZATION_NEVER (1) (never randomize the MAC address), or NM_SETTING_MAC_RANDOMIZATION_ALWAYS (2) (always randomize the MAC address). This property is deprecated for 'cloned-mac-address'. Deprecated: 1</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.mode"></a>mode</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Wi-Fi network mode; one of "infrastructure", "adhoc" or "ap". If blank, infrastructure is assumed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.mtu"></a>mtu</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple Ethernet frames.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.name"></a>name</td>
<td align="left">string</td>
<td align="left">802-11-wireless</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.powersave"></a>powersave</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>One of NM_SETTING_WIRELESS_POWERSAVE_DISABLE (2) (disable Wi-Fi power saving), NM_SETTING_WIRELESS_POWERSAVE_ENABLE (3) (enable Wi-Fi power saving), NM_SETTING_WIRELESS_POWERSAVE_IGNORE (1) (don't touch currently configure setting) or NM_SETTING_WIRELESS_POWERSAVE_DEFAULT (0) (use the globally configured value). All other values are reserved.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.rate"></a>rate</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, directs the device to only use the specified bitrate for communication with the access point. Units are in Kb/s, ie 5500 = 5.5 Mbit/s. This property is highly driver dependent and not all devices support setting a static bitrate.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.security"></a>security</td>
<td align="left">None</td>
<td align="left"> </td>
<td>This property is deprecated, but can be set to the value '802-11-wireless-security' when a wireless security setting is also present in the connection dictionary, for compatibility with very old NetworkManager daemons.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.seen-bssids"></a>seen-bssids</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>A list of BSSIDs (each BSSID formatted as a MAC address like "00:11:22:33:44:55") that have been detected as part of the Wi-Fi network. NetworkManager internally tracks previously seen BSSIDs. The property is only meant for reading and reflects the BSSID list of NetworkManager. The changes you make to this property will not be preserved.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.ssid"></a>ssid</td>
<td align="left">byte array</td>
<td align="left"> </td>
<td>SSID of the Wi-Fi network. Must be specified.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless.tx-power"></a>tx-power</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>If non-zero, directs the device to use the specified transmit power. Units are dBm. This property is highly driver dependent and not all devices support setting a static transmit power.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="id-1.2.7.4.41"></a><h3>802-11-wireless-security setting</h3>
<p>Wi-Fi Security Settings.</p>
<div class="informaltable"><table class="informaltable" border="1">
<colgroup>
<col>
<col>
<col>
<col>
</colgroup>
<thead><tr>
<th>Key Name</th>
<th>Value Type</th>
<th>Default Value</th>
<th>Value Description</th>
</tr></thead>
<tbody>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.auth-alg"></a>auth-alg</td>
<td align="left">string</td>
<td align="left"> </td>
<td>When WEP is used (ie, key-mgmt = "none" or "ieee8021x") indicate the 802.11 authentication algorithm required by the AP here. One of "open" for Open System, "shared" for Shared Key, or "leap" for Cisco LEAP. When using Cisco LEAP (ie, key-mgmt = "ieee8021x" and auth-alg = "leap") the "leap-username" and "leap-password" properties must be specified.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.group"></a>group</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>A list of group/broadcast encryption algorithms which prevents connections to Wi-Fi networks that do not utilize one of the algorithms in the list. For maximum compatibility leave this property empty. Each list element may be one of "wep40", "wep104", "tkip", or "ccmp".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.key-mgmt"></a>key-mgmt</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Key management used for the connection. One of "none" (WEP), "ieee8021x" (Dynamic WEP), "wpa-none" (Ad-Hoc WPA-PSK), "wpa-psk" (infrastructure WPA-PSK), or "wpa-eap" (WPA-Enterprise). This property must be set for any Wi-Fi connection that uses security.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.leap-password"></a>leap-password</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The login password for legacy LEAP connections (ie, key-mgmt = "ieee8021x" and auth-alg = "leap").</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.leap-password-flags"></a>leap-password-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "leap-password" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.leap-username"></a>leap-username</td>
<td align="left">string</td>
<td align="left"> </td>
<td>The login username for legacy LEAP connections (ie, key-mgmt = "ieee8021x" and auth-alg = "leap").</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.name"></a>name</td>
<td align="left">string</td>
<td align="left">802-11-wireless-security</td>
<td>The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "wireless" or "wired".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.pairwise"></a>pairwise</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>A list of pairwise encryption algorithms which prevents connections to Wi-Fi networks that do not utilize one of the algorithms in the list. For maximum compatibility leave this property empty. Each list element may be one of "tkip" or "ccmp".</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.pmf"></a>pmf</td>
<td align="left">int32</td>
<td align="left">0</td>
<td>Indicates whether Protected Management Frames (802.11w) must be enabled for the connection. One of NM_SETTING_WIRELESS_SECURITY_PMF_DEFAULT (0) (use global default value), NM_SETTING_WIRELESS_SECURITY_PMF_DISABLE (1) (disable PMF), NM_SETTING_WIRELESS_SECURITY_PMF_OPTIONAL (2) (enable PMF if the supplicant and the access point support it) or NM_SETTING_WIRELESS_SECURITY_PMF_REQUIRED (3) (enable PMF and fail if not supported). When set to NM_SETTING_WIRELESS_SECURITY_PMF_DEFAULT (0) and no global default is set, PMF will be optionally enabled.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.proto"></a>proto</td>
<td align="left">array of string</td>
<td align="left">[]</td>
<td>List of strings specifying the allowed WPA protocol versions to use. Each element may be one "wpa" (allow WPA) or "rsn" (allow WPA2/RSN). If not specified, both WPA and RSN connections are allowed.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.psk"></a>psk</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Pre-Shared-Key for WPA networks. If the key is 64-characters long, it must contain only hexadecimal characters and is interpreted as a hexadecimal WPA key. Otherwise, the key must be between 8 and 63 ASCII characters (as specified in the 802.11i standard) and is interpreted as a WPA passphrase, and is hashed to derive the actual WPA-PSK used when connecting to the Wi-Fi network.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.psk-flags"></a>psk-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "psk" property. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key-flags"></a>wep-key-flags</td>
<td align="left">NMSettingSecretFlags (uint32)</td>
<td align="left"> </td>
<td>Flags indicating how to handle the "wep-key0", "wep-key1", "wep-key2", and "wep-key3" properties. (see <a class="xref" href="nm-settings.html#secrets-flags" title="Secret flag types:">the section called “Secret flag types:”</a> for flag values)</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key-type"></a>wep-key-type</td>
<td align="left">NMWepKeyType (uint32)</td>
<td align="left"> </td>
<td>Controls the interpretation of WEP keys. Allowed values are NM_WEP_KEY_TYPE_KEY (1), in which case the key is either a 10- or 26-character hexadecimal string, or a 5- or 13-character ASCII password; or NM_WEP_KEY_TYPE_PASSPHRASE (2), in which case the passphrase is provided as a string and will be hashed using the de-facto MD5 method to derive the actual WEP key.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key0"></a>wep-key0</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Index 0 WEP key. This is the WEP key used in most networks. See the "wep-key-type" property for a description of how this key is interpreted.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key1"></a>wep-key1</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Index 1 WEP key. This WEP index is not used by most networks. See the "wep-key-type" property for a description of how this key is interpreted.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key2"></a>wep-key2</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Index 2 WEP key. This WEP index is not used by most networks. See the "wep-key-type" property for a description of how this key is interpreted.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-key3"></a>wep-key3</td>
<td align="left">string</td>
<td align="left"> </td>
<td>Index 3 WEP key. This WEP index is not used by most networks. See the "wep-key-type" property for a description of how this key is interpreted.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wep-tx-keyidx"></a>wep-tx-keyidx</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>When static WEP is used (ie, key-mgmt = "none") and a non-default WEP key index is used by the AP, put that WEP key index here. Valid values are 0 (default key) through 3. Note that some consumer access points (like the Linksys WRT54G) number the keys 1 - 4.</td>
</tr>
<tr>
<td align="left">
<a name="nm-settings.property.802-11-wireless-security.wps-method"></a>wps-method</td>
<td align="left">uint32</td>
<td align="left">0</td>
<td>Flags indicating which mode of WPS is to be used if any. There's little point in changing the default setting as NetworkManager will automatically determine whether it's feasible to start WPS enrollment from the Access Point capabilities. WPS can be disabled by setting this property to a value of 1.</td>
</tr>
</tbody>
</table></div>
</div>
<hr>
<div class="refsect2">
<a name="secrets-flags"></a><h3>Secret flag types:</h3>
<p>
Each password or secret property in a setting has an associated <span class="emphasis"><em>flags</em></span> property
that describes how to handle that secret. The <span class="emphasis"><em>flags</em></span> property is a bitfield
that contains zero or more of the following values logically OR-ed together.
</p>
<div class="itemizedlist"><ul class="itemizedlist" style="list-style-type: disc; ">
<li class="listitem"><p>0x0 (none) - the system is responsible for providing and storing this secret. This
may be required so that secrets are already available before the user logs in.
It also commonly means that the secret will be stored in plain text on disk, accessible
to root only. For example via the keyfile settings plugin as described in the "PLUGINS" section
in <a class="link" href="NetworkManager.conf.html" title="NetworkManager.conf"><span class="citerefentry"><span class="refentrytitle">NetworkManager.conf</span>(5)</span></a>.
</p></li>
<li class="listitem"><p>0x1 (agent-owned) - a user-session secret agent is responsible for providing and storing
this secret; when it is required, agents will be asked to provide it.</p></li>
<li class="listitem"><p>0x2 (not-saved) - this secret should not be saved but should be requested from the user
each time it is required. This flag should be used for One-Time-Pad secrets, PIN codes from hardware tokens,
or if the user simply does not want to save the secret.</p></li>
<li class="listitem"><p>0x4 (not-required) - in some situations it cannot be automatically determined that a secret
is required or not. This flag hints that the secret is not required and should not be requested from the user.</p></li>
</ul></div>
</div>
</div>
<div class="refsect1">
<a name="files"></a><h2>Files</h2>
<p><code class="filename">/etc/NetworkManager/system-connections</code> or distro plugin-specific location</p>
</div>
<div class="refsect1">
<a name="see_also"></a><h2>See Also</h2>
<p><a class="link" href="NetworkManager.html" title="NetworkManager"><span class="citerefentry"><span class="refentrytitle">NetworkManager</span>(8)</span></a>,
<a class="link" href="nmcli.html" title="nmcli"><span class="citerefentry"><span class="refentrytitle">nmcli</span>(1)</span></a>,
<a class="link" href="nmcli-examples.html" title="nmcli-examples"><span class="citerefentry"><span class="refentrytitle">nmcli-examples</span>(7)</span></a>,
<a class="link" href="NetworkManager.conf.html" title="NetworkManager.conf"><span class="citerefentry"><span class="refentrytitle">NetworkManager.conf</span>(5)</span></a></p>
</div>
</div>
<div class="footer">
<hr>Generated by GTK-Doc V1.27</div>
</body>
</html>
|