/etc/asterisk/extconfig.conf is in asterisk-config 1:13.18.3~dfsg-1ubuntu4.
This file is owned by root:root, with mode 0o640.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 | ;
; Static and realtime external configuration
; engine configuration
;
; See https://wiki.asterisk.org/wiki/display/AST/Realtime+Database+Configuration
; for basic table formatting information.
;
[settings]
;
; Static configuration files:
;
; file.conf => driver,database[,table[,priority]]
;
; maps a particular configuration file to the given
; database driver, database and table (or uses the
; name of the file as the table if not specified)
;
; Uncomment to load queues.conf via the odbc engine.
;
;queues.conf => odbc,asterisk,ast_config
;extensions.conf => sqlite,asterisk,ast_config
;
; The following files CANNOT be loaded from Realtime storage:
; asterisk.conf
; extconfig.conf (this file)
; logger.conf
;
; Additionally, the following files cannot be loaded from
; Realtime storage unless the storage driver is loaded
; early using 'preload' statements in modules.conf:
; manager.conf
; cdr.conf
; rtp.conf
;
; Named ACLs specified in realtime also can not be used
; from manager.conf unless the storage driver is preloaded.
; Attempting to use a realtime stored named ACL before the
; driver is loaded will result in an invalid ACL which
; rejects all addresses.
;
; Realtime configuration engine
;
; maps a particular family of realtime
; configuration to a given database driver,
; database and table (or uses the name of
; the family if the table is not specified
;
;example => odbc,asterisk,alttable,1
;example => mysql,asterisk,alttable,2
;example2 => ldap,"dc=oxymium,dc=net",example2
;
; Additionally, priorities are now supported for use as failover methods
; for retrieving realtime data. If one connection fails to retrieve any
; information, the next sequential priority will be tried next. This
; especially works well with ODBC connections, since res_odbc now caches
; when connection failures occur and prevents immediately retrying those
; connections until after a specified timeout. Note: priorities must
; start at 1 and be sequential (i.e. if you have only priorities 1, 2,
; and 4, then 4 will be ignored, because there is no 3).
;
;
; Possible driver backends:
;
; "odbc" is shown in the examples below, but is not the only valid realtime
; engine. Here are several of the possible options:
; odbc ... res_config_odbc
; sqlite ... res_config_sqlite
; sqlite3 ... res_config_sqlite3
; pgsql ... res_config_pgsql
; curl ... res_config_curl
; ldap ... res_config_ldap
; mysql ... res_config_mysql (available via add-ons in menuselect)
;
; Note: The res_config_pgsql and res_config_sqlite backends configure the
; database used in their respective configuration files and ignore the
; database name configured in this file.
;
;iaxusers => odbc,asterisk
;iaxpeers => odbc,asterisk
;sippeers => odbc,asterisk
;sipregs => odbc,asterisk ; (avoid sipregs if possible, e.g. by using a view)
;ps_endpoints => odbc,asterisk
;ps_auths => odbc,asterisk
;ps_aors => odbc,asterisk
;ps_domain_aliases => odbc,asterisk
;ps_endpoint_id_ips => odbc,asterisk
;ps_outbound_publishes => odbc,asterisk
;ps_inbound_publications = odbc,asterisk
;ps_asterisk_publications = odbc,asterisk
;voicemail => odbc,asterisk
;extensions => odbc,asterisk
;meetme => mysql,general
;queues => odbc,asterisk
;queue_members => odbc,asterisk
;queue_rules => odbc,asterisk
;acls => odbc,asterisk
;musiconhold => mysql,general
;queue_log => mysql,general
;
;
; While most dynamic realtime engines are automatically used when defined in
; this file, 'extensions', distinctively, is not. To activate dynamic realtime
; extensions, you must turn them on in each respective context within
; extensions.conf with a switch statement. The syntax is:
; switch => Realtime/[[db_context@]tablename]/<opts>
; The only option available currently is the 'p' option, which disallows
; extension pattern queries to the database. If you have no patterns defined
; in a particular context, this will save quite a bit of CPU time. However,
; note that using dynamic realtime extensions is not recommended anymore as a
; best practice; instead, you should consider writing a static dialplan with
; proper data abstraction via a tool like func_odbc.
|