amanda-server 1:3.5.1-1build2 / usr / share / amanda / template.d / advanced.conf

inparallel 4		# maximum dumpers that will run in parallel (max 63)
			# this maximum can be increased at compile-time,
			# modifying MAX_DUMPERS in server-src/driverio.h

dumporder "sssS"	# specify the priority order of each dumper
			#   s -> smallest size
			#   S -> biggest size
			#   t -> smallest time
			#   T -> biggest time
			#   b -> smallest bandwidth
			#   B -> biggest bandwitdh
			# try "BTBTBTBTBTBT" if you are not holding
			# disk constrained

taperalgo first		# The algorithm used to choose which dump image to send
			# to the taper.

			# Possible values: [first|firstfit|largest|largestfit|smallest|last]
			# Default: first. 

			# first		First in - first out.
			# firstfit 	The first dump image that will fit on the current tape.
			# largest 	The largest dump image.
			# largestfit 	The largest dump image that will fit on the current tape.
			# smallest 	The smallest dump image.
			# last 		Last in - first out.
displayunit "g"		# Possible values: "k|m|g|t"
			# Default: k. 
			# The unit used to print many numbers.
			# k=kilo, m=mega, g=giga, t=tera
netusage  8000 Kbps	# maximum net bandwidth for Amanda, in KB per sec

bumpsize 20 Mb		# minimum savings (threshold) to bump level 1 -> 2
bumppercent 20		# minimum savings (threshold) to bump level 1 -> 2
bumpdays 1		# minimum days at each level

device_output_buffer_size 1280k
                        # amount of buffer space to use when writing to devices

# If you want Amanda to automatically label any non-Amanda tapes it
# encounters, uncomment the line below. Note that this will ERASE any
# non-Amanda tapes you may have, and may also ERASE any near-failing tapes.
# Use with caution.
## autolabel "DailySet1-%%%" empty
			
maxdumpsize -1		# Maximum total size the planner will schedule
			# for a run (default: runtapes * tape_length) (kbytes).
bumpmult 4		# threshold = bumpsize * bumpmult^(level-1)



amrecover_changer "changer"	# amrecover will use the changer if you restore
    # from this device. It could be a string like 'changer' and amrecover will use your
    # changer if you set your tape to 'changer' with 'setdevice changer' or via 
    # 'tapedev "changer"' in amanda-client.conf




# If amanda cannot find a tape on which to store backups, it will run
# as many backups as it can to the holding disks.  In order to save
# space for unattended backups, by default, amanda will only perform
# incremental backups in this case, i.e., it will reserve 100% of the
# holding disk space for the so-called degraded mode backups.
# However, if you specify a different value for the `reserve'
# parameter, amanda will not degrade backups if they will fit in the
# non-reserved portion of the holding disk.

# reserve 30 # percent
# This means save at least 30% of the holding disk space for degraded
# mode backups.  

autoflush no 
# if autoflush is set to yes, then amdump will schedule all dump on
# holding disks to be flush to tape during the run.

# Amanda needs a few Mb of diskspace for the log and debug files,
# as well as a database.  This stuff can grow large, so the conf directory
# isn't usually appropriate.  Some sites use /usr/local/var and some /usr/adm.
# Create an amanda directory under there.  You need a separate infofile and
# logdir for each configuration, so create subdirectories for each conf and
# put the files there.  Specify the locations below.

# Note that, although the keyword below is infofile, it is only so for
# historic reasons, since now it is supposed to be a directory (unless
# you have selected some database format other than the `text' default)
infofile "/etc/amanda/DailySet1/curinfo"      # database DIRECTORY
logdir   "/etc/amanda/DailySet1"              # log directory
indexdir "/etc/amanda/DailySet1/index"        # index directory
#tapelist "@CONFIG_DIR/DailySet1/tapelist"	# list of used tapes
# tapelist is stored, by default, in the directory that contains amanda.conf

# Specify holding disks.  These are used as a temporary staging area for
# dumps before they are written to tape and are recommended for most sites.
# The advantages include: tape drive is more likely to operate in streaming
# mode (which reduces tape and drive wear, reduces total dump time); multiple
# dumps can be done in parallel (which can dramatically reduce total dump time.
# The main disadvantage is that dumps on the holding disk need to be flushed
# (with amflush) to tape after an operating system crash or a tape failure.
# If no holding disks are specified then all dumps will be written directly
# to tape.  If a dump is too big to fit on the holding disk than it will be
# written directly to tape.  If more than one holding disk is specified then
# they will all be used based on activity and available space.

#holdingdisk hd1 {
#    comment "main holding disk"
#    directory "/dumps/amanda"	# where the holding disk is
#    use -100 Mb		# how much space can we use on it
#			# a non-positive value means:
#			#        use all space but that value
#    chunksize 1Gb 	# size of chunk if you want big dump to be
#			# dumped on multiple files on holding disks
#			#  N Kb/Mb/Gb split images in chunks of size N
#			#	      The maximum value should be
#			#	      (MAX_FILE_SIZE - 1Mb)
#			#  0          same as INT_MAX bytes
#    }
#holdingdisk hd2 {
#    directory "/dumps2/amanda"
#    use 1000 Mb
#    }

# network interfaces
#
# These are referred to by the disklist file.  They define the attributes
# of the network interface that the remote machine is accessed through.
# Notes: - netusage above defines the attributes t
#          disklist entry doesn't specify otherwise.
#        - the values below are only samples.
#        - specifying an interface does not force the traffic to pass
#          through that interface.  Your OS routing tables do that.  This
#          is just a mechanism to stop Amanda trashing your network.
# Attributes are:
#	use		- bandwidth above which amanda won't start
#			  backups using this interface.  Note that if
#			  a single backup will take more than that,
#			  amanda won't try to make it run slower!

define interface local {
    comment "a local disk"
    use 8000 kbps
}

#define interface le0 {
#    comment "10 Mbps ethernet"
#    use 400 kbps
#}