hylafax-server 3:6.0.6-8 / var / spool / hylafax / config / class2.1

# $Id$
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 2.1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
# BEGIN-SERVER
#CountryCode:		1		# USA
#LongDistancePrefix:	1
#InternationalPrefix:	011
#AreaCode:		415
#DialStringRules:	etc/dialrules
#FAXNumber:		+1.999.555.1212
#LocalIdentifier:	"NothingSetup"	# default is canonical FAXNumber
#ServerTracing:		1		# log server-related operations
#SessionTracing:		11		# log server-related operations
#RecvFileMode:		0600		# recvd facsimile are not public
#LogFileMode:		0600		# private log files
#DeviceMode:		0600		# device is accessible only to uucp/fax
#GettyArgs:		"-h %l dx_%s"	# requires modem to auto-detect fax/data
#QualifyTSI:		etc/tsi		# accept facsimile from anyone
#SpeakerVolume:		off		# machine's are already too loud
#RingsBeforeAnswer:	1		# answer on first ring
#TagLineFont:		etc/lutRS18.pcf	# tag line font
#TagLineFormat:		"From %%l|%c|Page %%P of %%T"
#MaxBadCalls:		5		# max 5 consecutive bad calls
#PostScriptTimeout:	300		# 5 minute timeout on PostScript jobs
#MaxSendPages:		25		# max pages in an outbound job
#MaxRecvPages:		25		# max pages in an inbound job
#ContCoverPage:		etc/cover.templ	# enable continuation cover pages
#MaxConcurrentCalls:	1		# serialize jobs to the same dest
#TimeOfDay:		"Any"		# outbound jobs any day, any time
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.1	# use this to supply a hint
#ModemRate:		38400		# max rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemSoftResetCmdDelay:	3000	# pause after soft reset
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2.1 modems.
#
Class2Cmd:		AT+FCLASS=2.1	# command to enter class 2.1
Class2BORCmd:		AT+FBO=0	# bit order for phase B/C/D (direct)
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FKS		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FPP=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBU=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities command
Class2DISCmd:		AT+FIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FPI		# set polling identifier command
Class2NRCmd:		AT+FNR=1,1,1,1	# setup status reporting command
Class2PIECmd:		AT+FIE=0	# disable interrupt-enable command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=0	# set no flow control command
Class2SFLOCmd:		AT+FLO=1	# set software flow control command
Class2HFLOCmd:		AT+FLO=2	# set hardware flow control command