z8530-utils2 3.0-1-9 / etc / z8530drv.conf

This file is indexed.

/etc/z8530drv.conf is in z8530-utils2 3.0-1-9.

This file is owned by root:root, with mode 0o644.

The actual contents of the file can be viewed below. 

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
# z8530drv.conf - initialization for the Z8530 SCC driver v 2.4
#
# Lines must not be longer than 255 bytes!
#
#
# Hardware section
#
# SCC chip 1
#
chip	1
data_a  0x300			# data port A
ctrl_a  0x304			# control port A
data_b  0x301			# data port B
ctrl_b  0x305			# control port B
irq     5			# IRQ No. 5 (#)
pclock  4915200			# clock (+)
board   BAYCOM                  # hardware type (*)
escc    no			# enhanced SCC chip? (8580/85180/85280) (*)
vector  no			# latch for interrupt vector ($)
special no			# address of special function register (*)
option  0			# option to set via sfr (*)
#
# (*) option, default value is 0
# (+) option, default is 4915200
#
# SCC chip 2
#
chip	2
data_a  0x302
ctrl_a  0x306
data_b  0x303
ctrl_b  0x307
board   BAYCOM
#
# (#) all chips can share one interrupt, or you may use multiple INTs,
#     but there must be at least one IRQ defined in this system.
# ($) only one Vector Latch for all Chips is allowed.
#
#
# Software section
#
# The order of entries IS important!
#
# 	first     : DEVICE
# 	then      : MODEM section
# 	after that: Level 1 parameters
#
# Definition of /dev/scc0
#
device	/dev/scc0
#
# MODEM related stuff
#
speed	1200			# 1200 baud
clock	dpll			# clock source: use the dpll
mode	nrzi			# normal NRZI operation
#
# Level 1 parameters
#
txdelay 36			# You should know about these already!
persist 64
slot	8
tail	8
fulldup	0
wait    12
min	3
maxkey	7
idle	3
maxdef  120
group   0
txoff   off
softdcd on			# use software dcd
#
#
# Definition of /dev/scc1
#
#
device	/dev/scc1
#
speed	1200
clock	dpll
mode	nrzi
#
txdelay 36
persist 64
slot	8
tail	8
fulldup	0
wait    12
min	3
maxkey	7
idle	3
maxdef  120
group   0
txoff   off
softdcd off
#
#
# Definiton of /dev/scc2
#
#
device	/dev/scc2
#
speed	4800
clock	divider
mode	nrzi
#
txdelay 20
persist 64
slot	8
tail	8
fulldup	0
wait    12
min	3
maxkey	7
idle	3
maxdef  120
group   0
txoff   off
softdcd off
#
#
# Definition of /dev/scc3
#
#
device	/dev/scc3
speed	9600
clock	ext
mode	nrz
#
txdelay 8
persist 64
slot	8
tail	8
fulldup	0
wait    2
min	3
maxkey	7
idle	3
maxdef  120
group   0
txoff   off
softdcd off
#
# End of File
#

APT Browse - Built by Thomas Orozco.