/etc/neutron/plugins/linuxbridge/linuxbridge_conf.ini is in neutron-plugin-linuxbridge 1:2014.1-0ubuntu1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 | [vlans]
# (StrOpt) Type of network to allocate for tenant networks. The
# default value 'local' is useful only for single-box testing and
# provides no connectivity between hosts. You MUST change this to
# 'vlan' and configure network_vlan_ranges below in order for tenant
# networks to provide connectivity between hosts. Set to 'none' to
# disable creation of tenant networks.
#
# tenant_network_type = local
# Example: tenant_network_type = vlan
# (ListOpt) Comma-separated list of
# <physical_network>[:<vlan_min>:<vlan_max>] tuples enumerating ranges
# of VLAN IDs on named physical networks that are available for
# allocation. All physical networks listed are available for flat and
# VLAN provider network creation. Specified ranges of VLAN IDs are
# available for tenant network allocation if tenant_network_type is
# 'vlan'. If empty, only local networks may be created.
#
# network_vlan_ranges =
# Example: network_vlan_ranges = physnet1:1000:2999
[linux_bridge]
# (ListOpt) Comma-separated list of
# <physical_network>:<physical_interface> tuples mapping physical
# network names to the agent's node-specific physical network
# interfaces to be used for flat and VLAN networks. All physical
# networks listed in network_vlan_ranges on the server should have
# mappings to appropriate interfaces on each agent.
#
# physical_interface_mappings =
# Example: physical_interface_mappings = physnet1:eth1
[vxlan]
# (BoolOpt) enable VXLAN on the agent
# VXLAN support can be enabled when agent is managed by ml2 plugin using
# linuxbridge mechanism driver. Useless if set while using linuxbridge plugin.
# enable_vxlan = False
#
# (IntOpt) use specific TTL for vxlan interface protocol packets
# ttl =
#
# (IntOpt) use specific TOS for vxlan interface protocol packets
# tos =
#
# (StrOpt) multicast group to use for broadcast emulation.
# This group must be the same on all the agents.
# vxlan_group = 224.0.0.1
#
# (StrOpt) Local IP address to use for VXLAN endpoints (required)
# local_ip =
#
# (BoolOpt) Flag to enable l2population extension. This option should be used
# in conjunction with ml2 plugin l2population mechanism driver (in that case,
# both linuxbridge and l2population mechanism drivers should be loaded).
# It enables plugin to populate VXLAN forwarding table, in order to limit
# the use of broadcast emulation (multicast will be turned off if kernel and
# iproute2 supports unicast flooding - requires 3.11 kernel and iproute2 3.10)
# l2_population = False
[agent]
# Agent's polling interval in seconds
# polling_interval = 2
# (BoolOpt) Enable server RPC compatibility with old (pre-havana)
# agents.
#
# rpc_support_old_agents = False
# Example: rpc_support_old_agents = True
[securitygroup]
# Firewall driver for realizing neutron security group function
# firewall_driver = neutron.agent.firewall.NoopFirewallDriver
# Example: firewall_driver = neutron.agent.linux.iptables_firewall.IptablesFirewallDriver
# Controls if neutron security group is enabled or not.
# It should be false when you use nova security group.
# enable_security_group = True
|