/usr/share/doc/gmt/html/man/greenspline.html is in gmt-doc 4.5.11-1build1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 | <!-- Creator : groff version 1.19.2 -->
<!-- CreationDate: Tue Nov 5 09:45:29 2013 -->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"
"http://www.w3.org/TR/html4/loose.dtd">
<html>
<head>
<meta name="generator" content="groff -Thtml, see www.gnu.org">
<meta http-equiv="Content-Type" content="text/html; charset=US-ASCII">
<meta name="Content-Style" content="text/css">
<style type="text/css">
p { margin-top: 0; margin-bottom: 0; }
pre { margin-top: 0; margin-bottom: 0; }
table { margin-top: 0; margin-bottom: 0; }
</style>
<title>GREENSPLINE</title>
</head>
<body bgcolor="#ffffff">
<h1 align=center>GREENSPLINE</h1>
<a href="#NAME">NAME</a><br>
<a href="#SYNOPSIS">SYNOPSIS</a><br>
<a href="#DESCRIPTION">DESCRIPTION</a><br>
<a href="#OPTIONS">OPTIONS</a><br>
<a href="#1-D EXAMPLES">1-D EXAMPLES</a><br>
<a href="#2-D EXAMPLES">2-D EXAMPLES</a><br>
<a href="#3-D EXAMPLES">3-D EXAMPLES</a><br>
<a href="#2-D SPHERICAL SURFACE EXAMPLES">2-D SPHERICAL SURFACE EXAMPLES</a><br>
<a href="#CONSIDERATIONS">CONSIDERATIONS</a><br>
<a href="#TENSION">TENSION</a><br>
<a href="#REFERENCES">REFERENCES</a><br>
<a href="#SEE ALSO">SEE ALSO</a><br>
<hr>
<a name="NAME"></a>
<h2>NAME</h2>
<p style="margin-left:11%; margin-top: 1em">greenspline
− Interpolate 1-D, 2-D, 3-D Cartesian or spherical
surface data using Green’s function splines.</p>
<a name="SYNOPSIS"></a>
<h2>SYNOPSIS</h2>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
[ <i>datafile(s)</i> ] [
<b>−A</b>[<b>1</b>|<b>2</b>|<b>3</b>|<b>4</b>|<b>5</b>,]<i>gradfile</i>
] [ <b>−C</b><i>cut</i>[/<i>file</i>] ] [
<b>−D</b><i>mode</i> ] [ <b>−F</b> ] [
<b>−G</b><i>grdfile</i> ] [
<b>−H</b>[<b>i</b>][<i>nrec</i>] ] [
<b>−I</b><i>xinc</i>[<i>yinc</i>[<i>zinc</i>]] ] [
<b>−L</b> ] [ <b>−N</b><i>nodefile</i> ] [
<b>−Q</b><i>az</i>|<i>x/y/z</i> ] [
<b>−R</b><i>xmin</i>/<i>xmax</i>[/<i>ymin</i>/<i>ymax</i>[/<i>zminzmax</i>]]
] [ <b>−Sc|t|g|p|q</b>[<i>pars</i>] ] [
<b>−T</b><i>maskgrid</i> ] [ <b>−V</b> ] [
<b>−:</b>[<b>i</b>|<b>o</b>] ] [
<b>−bi</b>[<b>s</b>|<b>S</b>|<b>d</b>|<b>D</b>[<i>ncol</i>]|<b>c</b>[<i>var1</i><b>/</b><i>...</i>]]
] [ <b>−f</b>[<b>i</b>|<b>o</b>]<i>colinfo</i> ] [
<b>−bo</b>[<b>s</b>|<b>S</b>|<b>d</b>|<b>D</b>[<i>ncol</i>]|<b>c</b>[<i>var1</i><b>/</b><i>...</i>]]
]</p>
<a name="DESCRIPTION"></a>
<h2>DESCRIPTION</h2>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
uses the Green’s function G(<b>x</b>; <b>x’</b>)
for the chosen spline and geometry to interpolate data at
regular [or arbitrary] output locations. Mathematically, the
solution is composed as <i>w</i>(<b>x</b>) = sum
{<i>c</i>(<i>i</i>) G(<b>x</b>; <b>x</b>(<i>i</i>))}, for
<i>i</i> = 1, <i>n</i>, the number of data points
{<b>x</b>(<i>i</i>), <i>w</i>(<i>i</i>)}. Once the <i>n</i>
coefficients <i>c</i>(<i>i</i>) have been found then the sum
can be evaluated at any output point <b>x</b>. Choose
between ten minimum curvature, regularized, or continuous
curvature splines in tension for either 1-D, 2-D, or 3-D
Cartesian coordinates or spherical surface coordinates.
After first removing a linear or planar trend (Cartesian
geometries) or mean value (spherical surface) and
normalizing these residuals, the least-squares matrix
solution for the spline coefficients <i>c</i>(<i>i</i>) is
found by solving the <i>n</i> by <i>n</i> linear system
<i>w</i>(<i>j</i>) = sum-over-<i>i</i> {<i>c</i>(<i>i</i>)
G(<b>x</b>(<i>j</i>); <b>x</b>(<i>i</i>))}, for <i>j</i> =
1, <i>n</i>; this solution yields an exact interpolation of
the supplied data points. Alternatively, you may choose to
perform a singular value decomposition (SVD) and eliminate
the contribution from the smallest eigenvalues; this
approach yields an approximate solution. Trends and scales
are restored when evaluating the output.</p>
<a name="OPTIONS"></a>
<h2>OPTIONS</h2>
<p style="margin-left:11%; margin-top: 1em"><i>datafile(s)</i></p>
<p style="margin-left:22%;">The name of one or more ASCII
[or binary, see <b>−bi</b>] files holding the
<b>x</b>, <i>w</i> data points. If no file is given then we
read standard input instead.</p>
<table width="100%" border=0 rules="none" frame="void"
cellspacing="0" cellpadding="0">
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−A</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">The solution will
partly be constrained by surface gradients <b>v</b> =
<i>v</i>*<b>n</b>, where <i>v</i> is the gradient magnitude
and <b>n</b> its unit vector direction. The gradient
direction may be specified either by Cartesian components
(either unit vector <b>n</b> and magnitude <i>v</i>
separately or gradient components <b>v</b> directly) or
angles w.r.t. the coordinate axes. Specify one of five input
formats: <b>0</b>: For 1-D data there is no direction, just
gradient magnitude (slope) so the input format is <i>x,
gradient</i>. Options 1-2 are for 2-D data sets: <b>1</b>:
records contain <i>x, y, azimuth, gradient</i>
(<i>azimuth</i> in degrees is measured clockwise from the
vertical (north) [Default]). <b>2</b>: records contain <i>x,
y, gradient, azimuth</i> (<i>azimuth</i> in degrees is
measured clockwise from the vertical (north)). Options 3-5
are for either 2-D or 3-D data: <b>3</b>: records contain
<b>x</b>, <i>direction(s), v</i> (<i>direction(s)</i> in
degrees are measured counter-clockwise from the horizontal
(and for 3-D the vertical axis). <b>4</b>: records contain
<b>x</b>, <b>v</b>. <b>5</b>: records contain <b>x</b>,
<b>n</b>, <i>v</i>. Append name of ASCII file with the
surface gradients (following a comma if a format is
specified).</p> </td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−C</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Find an approximate
surface fit: Solve the linear system for the spline
coefficients by SVD and eliminate the contribution from all
eigenvalues whose ratio to the largest eigenvalue is less
than <i>cut</i> [Default uses Gauss-Jordan elimination to
solve the linear system and fit the data exactly].
Optionally, append /<i>file</i> to save the eigenvalue
ratios to the specified file for further analysis. Finally,
if a negative <i>cut</i> is given then /<i>file</i> is
required and execution will stop after saving the
eigenvalues, i.e., no surface output is produced.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−D</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Sets the distance
flag that determines how we calculate distances between data
points. Select <i>mode</i> 0 for Cartesian 1-D spline
interpolation: <b>−D</b> 0 means (<i>x</i>) in user
units, Cartesian distances, Select <i>mode</i> 1-3 for
Cartesian 2-D surface spline interpolation: <b>−D</b>
1 means (<i>x,y</i>) in user units, Cartesian distances,
<b>−D</b> 2 for (<i>x,y</i>) in degrees, flat Earth
distances, and <b>−D</b> 3 for (<i>x,y</i>) in
degrees, spherical distances in km. Then, if
<b><A HREF="gmtdefaults.html#ELLIPSOID">ELLIPSOID</A></b> is spherical, we compute great circle arcs,
otherwise geodesics. Option <i>mode</i> = 4 applies to
spherical surface spline interpolation only: <b>−D</b>
4 for (<i>x,y</i>) in degrees, use cosine of great circle
(or geodesic) arcs. Select <i>mode</i> 5 for Cartesian 3-D
surface spline interpolation: <b>−D</b> 5 means
(<i>x,y,z</i>) in user units, Cartesian distances.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−F</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Force pixel
registration. [Default is gridline registration].</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−G</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Name of resulting
output file. (1) If options <b>−R</b>,
<b>−I</b>, and possibly <b>−F</b> are set we
produce an equidistant output table. This will be written to
stdout unless <b>−G</b> is specified. Note: for 2-D
grids the <b>−G</b> option is required. (2) If option
<b>−T</b> is selected then <b>−G</b> is required
and the output file is a 2-D binary grid file. Applies to
2-D interpolation only. (3) If <b>−N</b> is selected
then the output is an ASCII (or binary; see
<b>−bo</b>) table; if <b>−G</b> is not given
then this table is written to standard output. Ignored if
<b>−C</b> or <b>−C</b> 0 is given.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−H</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Input file(s) has
header record(s). If used, the default number of header
records is <b><A HREF="gmtdefaults.html#N_HEADER_RECS">N_HEADER_RECS</A></b>. Use <b>−Hi</b> if
only input data should have header records [Default will
write out header records if the input data have them]. Blank
lines and lines starting with # are always skipped.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−I</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Specify equidistant
sampling intervals, on for each dimension, separated by
slashes.</p> </td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−L</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Do <i>not</i>
remove a linear (1-D) or planer (2-D) trend when
<b>−D</b> selects mode 0-3 [For those Cartesian cases
a least-squares line or plane is modeled and removed, then
restored after fitting a spline to the residuals]. However,
in mixed cases with both data values and gradients, or for
spherical surface data, only the mean data value is removed
(and later and restored).</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−N</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">ASCII file with
coordinates of desired output locations <b>x</b> in the
first column(s). The resulting <i>w</i> values are appended
to each record and written to the file given in
<b>−G</b> [or stdout if not specified]; see
<b>−bo</b> for binary output instead. This option
eliminates the need to specify options <b>−R</b>,
<b>−I</b>, and <b>−F</b>.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−Q</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Rather than
evaluate the surface, take the directional derivative in the
<i>az</i> azimuth and return the magnitude of this
derivative instead. For 3-D interpolation, specify the three
components of the desired vector direction (the vector will
be normalized before use).</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="3%">
<p style="margin-top: 1em" valign="top"><b>−R</b></p> </td>
<td width="8%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Specify the domain
for an equidistant lattice where output predictions are
required. Requires <b>−I</b> and optionally
<b>−F</b>.</p> </td>
</table>
<p style="margin-left:22%;"><i>1-D:</i> Give
<i>xmin/xmax</i>, the minimum and maximum <i>x</i>
coordinates. <i><br>
2-D:</i> Give <i>xmin/xmax/ymin/ymax</i>, the minimum and
maximum <i>x</i> and <i>y</i> coordinates. These may be
Cartesian or geographical. If geographical, then <i>west,
east, south,</i> and <i>north</i> specify the Region of
interest, and you may specify them in decimal degrees or in
[+-]dd:mm[:ss.xxx][W|E|S|N] format. The two shorthands
<b>−Rg</b> and <b>−Rd</b> stand for global
domain (0/360 and -180/+180 in longitude respectively, with
-90/+90 in latitude). <i><br>
3-D:</i> Give <i>xmin/xmax/ymin/ymax/zmin/zmax</i>, the
minimum and maximum <i>x</i>, <i>y</i> and <i>z</i>
coordinates. See the 2-D section if your horizontal
coordinates are geographical; note the shorthands
<b>−Rg</b> and <b>−Rd</b> cannot be used if a
3-D domain is specified.</p>
<table width="100%" border=0 rules="none" frame="void"
cellspacing="0" cellpadding="0">
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−S</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Select one of five
different splines. The first two are used for 1-D, 2-D, or
3-D Cartesian splines (see <b>−D</b> for discussion).
Note that all tension values are expected to be normalized
tension in the range 0 < <i>t</i> < 1: (<b>c</b>)
Minimum curvature spline [<i>Sandwell</i>, 1987], (<b>t</b>)
Continuous curvature spline in tension [<i>Wessel and
Bercovici</i>, 1998]; append <i>tension</i>[/<i>scale</i>]
with <i>tension</i> in the 0−1 range and optionally
supply a length scale [Default is the average grid spacing].
The next is a 2-D or 3-D spline: (<b>r</b>) Regularized
spline in tension [<i>Mitasova and Mitas</i>, 1993]; again,
append <i>tension</i> and optional <i>scale</i>. The last
two are spherical surface splines and both imply
<b>−D</b> 4 and geographic data: (<b>p</b>) Minimum
curvature spline [<i>Parker</i>, 1994], (<b>q</b>)
Continuous curvature spline in tension [<i>Wessel and
Becker</i>, 2008]; append <i>tension</i>. The G(<b>x</b>;
<b>x’</b>) for the last method is slower to compute;
by specifying <b>−SQ</b> you can speed up calculations
by first pre-calculating G(<b>x</b>; <b>x’</b>) for a
dense set of <b>x</b> values (e.g., 100,001 nodes between -1
to +1) and store them in look-up tables. Optionally append
/<i>N</i> (an odd integer) to specify how many points in the
spline to set [100001]</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−T</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">For 2-D
interpolation only. Only evaluate the solution at the nodes
in the <i>maskgrid</i> that are not equal to NaN. This
option eliminates the need to specify options
<b>−R</b>, <b>−I</b>, and <b>−F</b>.</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−V</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Selects verbose
mode, which will send progress reports to stderr [Default
runs "silently"].</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−bi</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Selects binary
input. Append <b>s</b> for single precision [Default is
<b>d</b> (double)]. Uppercase <b>S</b> or <b>D</b> will
force byte-swapping. Optionally, append <i>ncol</i>, the
number of columns in your binary input file if it exceeds
the columns needed by the program. Or append <b>c</b> if the
input file is netCDF. Optionally, append
<i>var1</i><b>/</b><i>var2</i><b>/</b><i>...</i> to specify
the variables to be read. [Default is 2-4 input columns
(<b>x</b>,<i>w</i>); the number depends on the chosen
dimension].</p> </td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−f</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Special formatting
of input and/or output columns (time or geographical data).
Specify <b>i</b> or <b>o</b> to make this apply only to
input or output [Default applies to both]. Give one or more
columns (or column ranges) separated by commas. Append
<b>T</b> (absolute calendar time), <b>t</b> (relative time
in chosen <b><A HREF="gmtdefaults.html#TIME_UNIT">TIME_UNIT</A></b> since <b><A HREF="gmtdefaults.html#TIME_EPOCH">TIME_EPOCH</A></b>),
<b>x</b> (longitude), <b>y</b> (latitude), or <b>f</b>
(floating point) to each column or column range item.
Shorthand <b>−f</b>[<b>i</b>|<b>o</b>]<b>g</b> means
<b>−f</b>[<b>i</b>|<b>o</b>]0<b>x</b>,1<b>y</b>
(geographic coordinates).</p></td>
<tr valign="top" align="left">
<td width="11%"></td>
<td width="4%">
<p style="margin-top: 1em" valign="top"><b>−bo</b></p> </td>
<td width="7%"></td>
<td width="78%">
<p style="margin-top: 1em" valign="top">Selects binary
output. Append <b>s</b> for single precision [Default is
<b>d</b> (double)]. Uppercase <b>S</b> or <b>D</b> will
force byte-swapping. Optionally, append <i>ncol</i>, the
number of desired columns in your binary output file.</p></td>
</table>
<a name="1-D EXAMPLES"></a>
<h2>1-D EXAMPLES</h2>
<p style="margin-left:11%; margin-top: 1em">To resample the
<i>x,y</i> Gaussian random data created by <b><A HREF="gmtmath.html">gmtmath</A></b>
and stored in 1D.txt, requesting output every 0.1 step from
0 to 10, and using a minimum cubic spline, try</p>
<p style="margin-left:11%; margin-top: 1em"><b>gmtmath
−T</b> 0/10/1 0 1 <b>NRAND</b> = 1D.txt <b><br>
psxy −R</b>0/10/-5/5 <b>−JX</b> 6i/3i
<b>−B</b> 2f1/1 <b>−Sc</b> 0.1 <b>−G</b>
black 1D.txt <b>−K</b> > 1D.ps <b><br>
greenspline</b> 1D.txt <b>−R</b> 0/10 <b>−I</b>
0.1 <b>−Sc −V</b> | <b>psxy −R −J
−O −W</b> thin >> 1D.ps</p>
<p style="margin-left:11%; margin-top: 1em">To apply a
spline in tension instead, using a tension of 0.7, try</p>
<p style="margin-left:11%; margin-top: 1em"><b>psxy
−R</b>0/10/-5/5 <b>−JX</b> 6i/3i <b>−B</b>
2f1/1 <b>−Sc</b> 0.1 <b>−G</b> black 1D.txt
<b>−K</b> > 1Dt.ps <b><br>
greenspline</b> 1D.txt <b>−R</b> 0/10 <b>−I</b>
0.1 <b>−St</b> 0.7 <b>−V</b> | <b>psxy −R
−J −O −W</b> thin >> 1Dt.ps</p>
<a name="2-D EXAMPLES"></a>
<h2>2-D EXAMPLES</h2>
<p style="margin-left:11%; margin-top: 1em">To make a
uniform grid using the minimum curvature spline for the same
Cartesian data set from Davis (1986) that is used in the GMT
Cookbook example 16, try</p>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
table_5.11 <b>−R</b> 0/6.5/-0.2/6.5 <b>−I</b>
0.1 <b>−Sc −V −D</b> 1 <b>−G</b>
S1987.grd <b><br>
psxy −R</b>0/6.5/-0.2/6.5 <b>−JX</b> 6i
<b>−B</b> 2f1 <b>−Sc</b> 0.1 <b>−G</b>
black table_5.11 <b>−K</b> > 2D.ps <b><br>
grdcontour −JX</b>6i <b>−B</b> 2f1 <b>−O
−C</b> 25 <b>−A</b> 50 S1987.grd >>
2D.ps</p>
<p style="margin-left:11%; margin-top: 1em">To use
Cartesian splines in tension but only evaluate the solution
where the input mask grid is not NaN, try</p>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
table_5.11 <b>−T</b> mask.grd <b>−St</b> 0.5
<b>−V −D</b> 1 <b>−G</b> WB1998.grd</p>
<p style="margin-left:11%; margin-top: 1em">To use
Cartesian generalized splines in tension and return the
magnitude of the surface slope in the NW direction, try</p>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
table_5.11 <b>−R</b> 0/6.5/-0.2/6.5 <b>−I</b>
0.1 <b>−Sr</b> 0.95 <b>−V −D</b> 1
<b>−Q</b>-45 <b>−G</b> slopes.grd Finally, to
use Cartesian minimum curvature splines in recovering a
surface where the input data is a single surface value
(pt.d) and the remaining constraints specify only the
surface slope and direction (slopes.d), use</p>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
pt.d <b>−R</b>-3.2/3.2/-3.2/3.2 <b>−I</b> 0.1
<b>−Sc −V −D</b> 1 <b>−A</b>
1,slopes.d <b>−G</b> slopes.grd</p>
<a name="3-D EXAMPLES"></a>
<h2>3-D EXAMPLES</h2>
<p style="margin-left:11%; margin-top: 1em">To create a
uniform 3-D Cartesian grid table based on the data in
table_5.23 in Davis (1986) that contains <i>x,y,z</i>
locations and a measure of uranium oxide concentrations (in
percent), try</p>
<p style="margin-left:11%; margin-top: 1em"><b>greenspline</b>
table_5.23 <b>−R</b> 5/40/-5/10/5/16 <b>−I</b>
0.25 <b>−Sr</b> 0.85 <b>−V −D</b> 5
<b>−G</b> 3D_UO2.txt</p>
<a name="2-D SPHERICAL SURFACE EXAMPLES"></a>
<h2>2-D SPHERICAL SURFACE EXAMPLES</h2>
<p style="margin-left:11%; margin-top: 1em">To recreate
Parker’s [1994] example on a global 1x1 degree grid,
assuming the data are in file mag_obs_1990.d, try</p>
<p style="margin-left:11%; margin-top: 1em">greenspline
<b>−V −Rg −Sp −D</b> 3
<b>−I</b> 1 <b>−G</b> P1994.grd
mag_obs_1990.d</p>
<p style="margin-left:11%; margin-top: 1em">To do the same
problem but applying tension and use pre-calculated Green
functions, use</p>
<p style="margin-left:11%; margin-top: 1em">greenspline
<b>−V −Rg −SQ</b> 0.85 <b>−D</b> 3
<b>−I</b> 1 <b>−G</b> WB2008.grd
mag_obs_1990.d</p>
<a name="CONSIDERATIONS"></a>
<h2>CONSIDERATIONS</h2>
<p style="margin-left:11%; margin-top: 1em">(1) For the
Cartesian cases we use the free-space Green functions, hence
no boundary conditions are applied at the edges of the
specified domain. For most applications this is fine as the
region typically is arbitrarily set to reflect the extent of
your data. However, if your application requires particular
boundary conditions then you may consider using
<b><A HREF="surface.html">surface</A></b> instead. <br>
(2) In all cases, the solution is obtained by inverting a
<i>n</i> x <i>n</i> double precision matrix for the Green
function coefficients, where <i>n</i> is the number of data
constraints. Hence, your computer’s memory may place
restrictions on how large data sets you can process with
<b>greenspline</b>. Pre-processing your data with
<b><A HREF="blockmean.html">blockmean</A></b>, <b><A HREF="blockmedian.html">blockmedian</A></b>, or <b><A HREF="blockmode.html">blockmode</A></b> is
recommended to avoid aliasing and may also control the size
of <i>n</i>. For information, if <i>n</i> = 1024 then only 8
Mb memory is needed, but for <i>n</i> = 10240 we need 800
Mb. Note that <b>greenspline</b> is fully 64-bit compliant
if compiled as such. <br>
(3) The inversion for coefficients can become numerically
unstable when data neighbors are very close compared to the
overall span of the data. You can remedy this by
pre-processing the data, e.g., by averaging closely spaced
neighbors. Alternatively, you can improve stability by using
the SVD solution and discard information associated with the
smallest eigenvalues (see <b>−C</b>).</p>
<a name="TENSION"></a>
<h2>TENSION</h2>
<p style="margin-left:11%; margin-top: 1em">Tension is
generally used to suppress spurious oscillations caused by
the minimum curvature requirement, in particular when rapid
gradient changes are present in the data. The proper amount
of tension can only be determined by experimentation.
Generally, very smooth data (such as potential fields) do
not require much, if any tension, while rougher data (such
as topography) will typically interpolate better with
moderate tension. Make sure you try a range of values before
choosing your final result. Note: the regularized spline in
tension is only stable for a finite range of <i>scale</i>
values; you must experiment to find the valid range and a
useful setting. For more information on tension see the
references below.</p>
<a name="REFERENCES"></a>
<h2>REFERENCES</h2>
<p style="margin-left:11%; margin-top: 1em">Davis, J. C.,
1986, <i>Statistics and Data Analysis in Geology</i>, 2nd
Edition, 646 pp., Wiley, New York, <br>
Mitasova, H., and L. Mitas, 1993, Interpolation by
regularized spline with tension: I. Theory and
implementation, <i>Math. Geol., 25</i>, 641−655. <br>
Parker, R. L., 1994, <i>Geophysical Inverse Theory</i>, 386
pp., Princeton Univ. Press, Princeton, N.J. <br>
Sandwell, D. T., 1987, Biharmonic spline interpolation of
Geos-3 and Seasat altimeter data, <i>Geophys. Res. Lett.,
14</i>, 139−142. <br>
Wessel, P., and D. Bercovici, 1998, Interpolation with
splines in tension: a Green’s function approach,
<i>Math. Geol., 30</i>, 77−93. <br>
Wessel, P., and J. M. Becker, 2008, Interpolation using a
generalized Green’s function for a spherical surface
spline in tension, <i>Geophys. J. Int, 174</i>, 21−28.
<br>
Wessel, P., 2009, A general-purpose Green’s function
interpolator, <i>Computers & Geosciences, 35</i>,
1247−1254, doi:10.1016/j.cageo.2008.08.012.</p>
<a name="SEE ALSO"></a>
<h2>SEE ALSO</h2>
<p style="margin-left:11%; margin-top: 1em"><i><A HREF="GMT.html">GMT</A></i>(1),
<i><A HREF="gmtmath.html">gmtmath</A></i>(1), <i><A HREF="nearneighbor.html">nearneighbor</A></i>(1), <i><A HREF="psxy.html">psxy</A></i>(1),
<i><A HREF="surface.html">surface</A></i>(1), <i><A HREF="triangulate.html">triangulate</A></i>(1),
<i><A HREF="xyz2grd.html">xyz2grd</A></i>(1)</p>
<hr>
</body>
</html>
|