/usr/share/zentyal/stubs/network/dsl-provider.mas is in zentyal-network 2.3.13+quantal1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 | <%args>
$iface
$ppp_user
$usepeerdns
</%args>
# Configuration file for PPP, using PPP over Ethernet
# to connect to a DSL provider.
#
# See the manual page pppd(8) for information on all the options.
##
# Section 1
#
# Stuff to configure...
# MUST CHANGE: Uncomment the following line, replacing the user@provider.net
# by the DSL user name given to your by your DSL provider.
# (There should be a matching entry in /etc/ppp/pap-secrets with the password.)
user <% $ppp_user %>
# Use the pppoe program to send the ppp packets over the Ethernet link
# This line should work fine if this computer is the only one accessing
# the Internet through this DSL connection. This is the right line to use
# for most people.
#pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1452"
# An even more conservative version of the previous line, if things
# don't work using -m 1452...
#pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1412"
# If the computer connected to the Internet using pppoe is not being used
# by other computers as a gateway to the Internet, you can try the following
# line instead, for a small gain in speed:
#pty "/usr/sbin/pppoe -I eth0 -T 80"
# The following two options should work fine for most DSL users.
# Assumes that your IP address is allocated dynamically
# by your DSL provider...
noipdefault
% if ($usepeerdns) {
# Try to get the name server addresses from the ISP.
usepeerdns
% }
# Use this connection as the default route.
# Comment out if you already have the correct default route installed.
#defaultroute
##
# Section 2
#
# Uncomment if your DSL provider charges by minute connected
# and you want to use demand-dialing.
#
# Disconnect after 300 seconds (5 minutes) of idle time.
#demand
#idle 300
##
# Section 3
#
# You shouldn't need to change these options...
hide-password
lcp-echo-interval 20
lcp-echo-failure 3
# Override any connect script that may have been set in /etc/ppp/options.
connect /bin/true
noauth
persist
mtu 1492
# RFC 2516, paragraph 7 mandates that the following options MUST NOT be
# requested and MUST be rejected if requested by the peer:
# Address-and-Control-Field-Compression (ACFC)
noaccomp
# Asynchronous-Control-Character-Map (ACCM)
default-asyncmap
# Always retry on fail
maxfail 0
# Added for eBox
# Used to pass the name of the ethernet interface to the ip-up.d script
ipparam <% $iface %>
plugin rp-pppoe.so <% $iface %>
|