gvpe 2.25-2 / usr / share / doc / gvpe / examples / gvpe.conf

This file is indexed.

/usr/share/doc/gvpe/examples/gvpe.conf is in gvpe 2.25-2.

This file is owned by root:root, with mode 0o644.

The actual contents of the file can be viewed below. 

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
# sample configfile
# the config file must be exactly(!) the same on all nodes

rekey = 54321		# the rekeying interval
keepalive = 300		# the keepalive interval
on ruth keepalive = 120	# ruth is important and demands lower keepalives
on surfer keepalive = 40
mtu = 1492		# the mtu (minimum mtu of attached host)
ifname = vpn0		# the tunnel interface name to use
ifpersist = no		# the tun device should be persistent
inherit-tos = yes	# should tunnel packets inherit tos flags?
compress = yes		# wether compression should be used (NYI)
connect = ondemand	# connect to this host always/never or ondemand
router-priority = 1	# route for everybody - if necessary

loglevel = notice	# info logs connects, notice only important messages
on mobil loglevel = info
on doom loglevel = info
on ruth loglevel = info

udp-port = 407		# the udp port to use for sending/receiving packets
tcp-port = 443		# the tcp port to listen for connections (we use https over proxy)
ip-proto = 50		# (ab)use the ipsec protocol as rawip
icmp-type = 0		# (ab)use echo replies for tunneling
enable-udp = yes	# udp is spoken almost everywhere
enable-tcp = no		# tcp is not spoken everywhere
enable-rawip = no	# rawip is not spoken everywhere
enable-icmp = no	# most hosts don't bother to icmp

# every "node =" introduces a new node in the network
# the options following it don't set defaults but are
# node-specific.

# marc@lap
node = mobil

# marc@home
node = doom
enable-rawip = yes
enable-tcp = yes

# marc@uni
node = ruth
enable-rawip = yes
enable-tcp = yes
enable-icmp = yes
hostname = 200.100.162.95
connect = always
router-priority = 30
on ruth node-up = node-up
on ruth node-down = node-up

# marc@mu
node = frank
enable-rawip = yes
hostname = 44.88.167.250
router-priority = 20
connect = always

# nethype
node = rain
enable-rawip = yes
hostname = 145.253.105.130
router-priority = 10
connect = always

# marco@home
node = marco
enable-rawip = yes

# stefan@ka
node = wappla
connect = never

# stefan@lap
node = stefan
udp-port = 408
connect = never

# paul@wg
node = n8geil
on ruth enable-icmp = yes
on n8geil enable-icmp = yes
enable-udp = no

# paul@lap
node = syrr

# paul@lu
node = donomos

# marco@hn
node = core

# elmex@home
node = elmex
enable-rawip = yes
hostname = 100.251.143.181

# stefan@kwc.at
node = fwkw
connect = never
on stefan connect = always
on wappla connect = always
hostname = 182.73.81.146

# elmex@home
node = jungfrau
enable-rawip = yes

# uni main router
node = surfer
enable-rawip = yes
enable-tcp = no
enable-icmp = yes
hostname = 200.100.162.79
connect = always
router-priority = 40

# jkneer@marvin
node = marvin
enable-rawip = yes
enable-udp = no

# jkneer@entrophy
node = entrophy
enable-udp = no
enable-tcp = yes

# mr. primitive
node = voyager
enable-udp = no
enable-tcp = no
on voyager enable-tcp = yes
on voyager enable-udp = yes

# v-server (barbados.dn-systems.de)
#node = vserver
#enable-udp = yes
#hostname = 193.108.181.74

APT Browse - Built by Thomas Orozco.