/usr/share/doc/ghostscript-doc/Deprecated.htm is in ghostscript-doc 9.18~dfsg~0-0ubuntu2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2629 2630 2631 2632 2633 2634 2635 2636 2637 2638 2639 2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650 2651 2652 2653 2654 2655 2656 2657 2658 2659 2660 2661 2662 2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673 2674 2675 2676 2677 2678 2679 2680 2681 2682 2683 2684 2685 2686 2687 2688 2689 2690 2691 2692 2693 2694 2695 2696 2697 2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2715 2716 2717 2718 2719 2720 2721 2722 2723 2724 2725 2726 2727 2728 2729 2730 2731 2732 2733 2734 2735 2736 2737 2738 2739 2740 2741 2742 2743 2744 2745 2746 2747 2748 2749 2750 2751 2752 2753 2754 2755 2756 2757 2758 2759 2760 2761 2762 2763 2764 2765 2766 2767 2768 2769 2770 2771 2772 2773 2774 2775 2776 2777 2778 2779 2780 2781 2782 2783 2784 2785 2786 2787 2788 2789 2790 2791 2792 2793 2794 2795 2796 2797 2798 2799 2800 2801 2802 2803 2804 2805 2806 2807 2808 2809 2810 2811 2812 2813 2814 2815 2816 2817 2818 2819 2820 2821 2822 2823 2824 2825 2826 2827 2828 2829 2830 2831 2832 2833 2834 2835 2836 2837 2838 2839 2840 2841 2842 2843 2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854 2855 2856 2857 2858 2859 2860 2861 2862 2863 2864 2865 2866 2867 2868 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878 2879 2880 2881 2882 2883 2884 2885 2886 2887 2888 2889 2890 2891 2892 2893 2894 2895 2896 2897 2898 2899 2900 2901 2902 2903 2904 2905 2906 2907 2908 2909 2910 2911 2912 2913 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923 2924 2925 2926 2927 2928 2929 2930 2931 2932 2933 2934 2935 2936 2937 2938 2939 2940 2941 2942 2943 2944 2945 2946 2947 2948 2949 2950 2951 2952 2953 2954 2955 2956 2957 2958 2959 2960 2961 2962 2963 2964 2965 2966 2967 2968 2969 2970 2971 2972 2973 2974 2975 2976 2977 2978 2979 2980 2981 2982 2983 2984 2985 2986 2987 2988 2989 2990 2991 2992 2993 2994 2995 2996 2997 2998 2999 3000 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048 3049 3050 3051 3052 3053 3054 3055 3056 3057 3058 3059 3060 3061 3062 3063 3064 3065 3066 3067 3068 3069 3070 3071 3072 3073 3074 3075 3076 3077 3078 3079 3080 3081 3082 3083 3084 3085 3086 3087 3088 3089 3090 3091 3092 3093 3094 3095 3096 3097 3098 3099 3100 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3111 3112 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3126 3127 3128 3129 3130 3131 3132 3133 3134 3135 3136 3137 3138 3139 3140 3141 3142 3143 3144 3145 3146 3147 3148 3149 3150 3151 3152 3153 3154 3155 3156 3157 3158 3159 3160 3161 3162 3163 3164 3165 3166 3167 3168 3169 3170 3171 3172 3173 3174 3175 3176 3177 3178 3179 3180 3181 3182 3183 3184 3185 3186 3187 3188 3189 3190 3191 3192 3193 3194 3195 3196 3197 3198 3199 3200 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3213 3214 3215 3216 3217 3218 3219 3220 3221 3222 3223 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 3237 3238 3239 3240 3241 3242 3243 3244 3245 3246 3247 3248 3249 3250 3251 3252 3253 3254 3255 3256 3257 3258 3259 3260 3261 3262 3263 3264 3265 3266 3267 3268 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3281 3282 3283 3284 3285 3286 3287 3288 3289 3290 3291 3292 3293 3294 3295 3296 3297 3298 3299 3300 3301 3302 3303 3304 3305 3306 3307 3308 3309 3310 3311 3312 3313 3314 3315 3316 3317 3318 3319 3320 3321 3322 3323 3324 3325 3326 3327 3328 3329 3330 3331 3332 3333 3334 3335 3336 3337 3338 3339 3340 3341 3342 3343 3344 3345 3346 3347 3348 3349 3350 3351 3352 3353 3354 3355 3356 3357 3358 3359 3360 3361 3362 3363 3364 3365 3366 3367 3368 3369 3370 3371 3372 3373 3374 3375 3376 3377 3378 3379 3380 3381 3382 3383 3384 3385 3386 3387 3388 3389 3390 3391 3392 3393 3394 3395 3396 3397 3398 3399 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 3410 3411 3412 3413 3414 3415 3416 3417 3418 3419 3420 3421 3422 3423 3424 3425 3426 3427 3428 3429 3430 3431 3432 3433 3434 3435 3436 3437 3438 3439 3440 3441 3442 3443 3444 3445 3446 3447 3448 3449 3450 3451 3452 3453 3454 3455 3456 3457 3458 3459 3460 3461 3462 3463 3464 3465 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3476 3477 3478 3479 3480 3481 3482 3483 3484 3485 3486 3487 3488 3489 3490 3491 3492 3493 3494 3495 3496 3497 3498 3499 3500 3501 3502 3503 3504 3505 3506 3507 3508 3509 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3525 3526 3527 3528 3529 3530 3531 3532 3533 3534 3535 3536 3537 3538 3539 3540 3541 3542 3543 3544 3545 3546 3547 3548 3549 3550 3551 3552 3553 3554 3555 3556 3557 3558 3559 3560 3561 3562 3563 3564 3565 3566 3567 3568 3569 3570 3571 3572 3573 3574 3575 3576 3577 3578 3579 3580 3581 3582 3583 3584 3585 3586 3587 3588 3589 3590 3591 3592 3593 3594 3595 3596 3597 3598 3599 3600 3601 3602 3603 3604 3605 3606 3607 3608 3609 3610 3611 3612 3613 3614 3615 3616 3617 3618 3619 3620 3621 3622 3623 3624 3625 3626 3627 3628 3629 3630 3631 3632 3633 3634 3635 3636 3637 3638 3639 3640 3641 3642 3643 3644 3645 3646 3647 3648 3649 3650 3651 3652 3653 3654 3655 3656 3657 3658 3659 3660 3661 3662 3663 3664 3665 3666 3667 3668 3669 3670 3671 3672 3673 3674 3675 3676 3677 3678 3679 3680 3681 3682 3683 3684 3685 3686 3687 3688 3689 3690 3691 3692 3693 3694 3695 3696 3697 3698 3699 3700 3701 3702 3703 3704 3705 3706 3707 3708 3709 3710 3711 3712 3713 3714 3715 3716 3717 3718 3719 3720 3721 3722 3723 3724 3725 3726 3727 3728 3729 3730 3731 3732 3733 3734 3735 3736 3737 3738 3739 3740 3741 3742 3743 3744 3745 3746 3747 3748 3749 3750 3751 3752 3753 3754 3755 3756 3757 3758 3759 3760 3761 3762 3763 3764 3765 3766 3767 3768 3769 3770 3771 3772 3773 3774 3775 3776 3777 3778 3779 3780 3781 3782 3783 3784 3785 3786 3787 3788 3789 3790 3791 3792 3793 3794 3795 3796 3797 3798 3799 3800 3801 3802 3803 3804 3805 3806 3807 3808 3809 3810 3811 3812 3813 3814 3815 3816 3817 3818 3819 3820 3821 3822 3823 3824 3825 3826 3827 3828 3829 3830 3831 3832 3833 3834 3835 3836 3837 3838 3839 3840 3841 3842 3843 3844 3845 3846 3847 3848 3849 3850 3851 3852 3853 3854 3855 3856 3857 3858 3859 3860 3861 3862 3863 3864 3865 3866 3867 3868 3869 3870 3871 3872 3873 3874 3875 3876 3877 3878 3879 3880 3881 3882 3883 3884 3885 3886 3887 3888 3889 3890 3891 3892 3893 3894 3895 3896 3897 3898 3899 3900 3901 3902 3903 3904 3905 3906 3907 3908 3909 3910 3911 3912 3913 3914 3915 3916 3917 3918 3919 3920 3921 3922 3923 3924 3925 3926 3927 3928 3929 3930 3931 3932 3933 3934 3935 3936 3937 3938 3939 3940 3941 3942 3943 3944 3945 3946 3947 3948 3949 3950 3951 3952 3953 3954 3955 3956 3957 3958 3959 3960 3961 3962 3963 3964 3965 3966 3967 3968 3969 3970 3971 3972 3973 3974 3975 3976 3977 3978 3979 3980 3981 3982 3983 3984 3985 3986 3987 3988 3989 3990 3991 3992 3993 3994 3995 3996 3997 3998 3999 4000 4001 4002 4003 4004 4005 4006 4007 4008 4009 4010 4011 4012 4013 4014 4015 4016 4017 4018 4019 4020 4021 4022 4023 4024 4025 4026 4027 4028 4029 4030 4031 4032 4033 4034 4035 4036 4037 4038 4039 4040 4041 4042 4043 4044 4045 4046 4047 4048 4049 4050 4051 4052 4053 4054 4055 4056 4057 4058 4059 4060 4061 4062 4063 4064 4065 4066 4067 4068 4069 4070 4071 4072 4073 4074 4075 4076 4077 4078 4079 4080 4081 4082 4083 4084 4085 4086 4087 4088 4089 4090 4091 4092 4093 4094 4095 4096 4097 4098 4099 4100 4101 4102 4103 4104 4105 4106 4107 4108 4109 4110 4111 4112 4113 4114 4115 4116 4117 4118 4119 4120 4121 4122 4123 4124 4125 4126 4127 4128 4129 4130 4131 4132 4133 4134 4135 4136 4137 4138 4139 4140 4141 4142 4143 4144 4145 4146 4147 4148 4149 4150 4151 4152 4153 4154 4155 4156 4157 4158 4159 4160 4161 4162 4163 4164 4165 4166 4167 4168 4169 4170 4171 4172 4173 4174 4175 4176 4177 4178 4179 4180 4181 4182 4183 4184 4185 4186 4187 4188 4189 4190 4191 4192 4193 4194 4195 4196 4197 4198 4199 4200 4201 4202 4203 4204 4205 4206 4207 4208 4209 4210 4211 4212 4213 4214 4215 4216 4217 4218 4219 4220 4221 4222 4223 4224 4225 4226 4227 4228 4229 4230 4231 4232 4233 4234 4235 4236 4237 4238 4239 4240 4241 4242 4243 4244 4245 4246 4247 4248 4249 4250 4251 4252 4253 4254 4255 4256 4257 4258 4259 4260 4261 4262 4263 4264 4265 4266 4267 4268 4269 4270 4271 4272 4273 4274 4275 4276 4277 4278 4279 4280 4281 4282 4283 4284 4285 4286 4287 4288 4289 4290 4291 4292 4293 4294 4295 4296 4297 4298 4299 4300 4301 4302 4303 4304 4305 4306 4307 4308 4309 4310 4311 4312 4313 4314 4315 4316 4317 4318 4319 4320 4321 4322 4323 4324 4325 4326 4327 4328 4329 4330 4331 4332 4333 4334 4335 4336 4337 4338 4339 4340 4341 4342 4343 4344 4345 4346 4347 4348 4349 4350 4351 4352 4353 4354 4355 4356 4357 4358 4359 4360 4361 4362 4363 4364 4365 4366 4367 4368 4369 4370 4371 4372 4373 4374 4375 4376 4377 4378 4379 4380 4381 4382 4383 4384 4385 4386 4387 4388 4389 4390 4391 4392 4393 4394 4395 4396 4397 4398 4399 4400 4401 4402 4403 4404 4405 4406 4407 4408 4409 4410 4411 4412 4413 4414 4415 4416 4417 4418 4419 4420 4421 4422 4423 4424 4425 4426 4427 4428 4429 4430 4431 4432 4433 4434 4435 4436 4437 4438 4439 4440 4441 4442 4443 4444 4445 4446 4447 4448 4449 4450 4451 4452 4453 4454 4455 4456 4457 4458 4459 4460 4461 4462 4463 4464 4465 4466 4467 4468 4469 4470 4471 4472 4473 4474 4475 4476 4477 4478 4479 4480 4481 4482 4483 4484 4485 4486 4487 4488 4489 4490 4491 4492 4493 4494 4495 4496 4497 4498 4499 4500 4501 4502 4503 4504 4505 4506 4507 4508 4509 4510 4511 4512 4513 4514 4515 4516 4517 4518 4519 4520 4521 4522 4523 4524 4525 4526 4527 4528 4529 4530 4531 4532 4533 4534 4535 4536 4537 4538 4539 4540 4541 4542 4543 4544 4545 4546 4547 4548 4549 4550 4551 4552 4553 4554 4555 4556 4557 4558 4559 4560 4561 4562 4563 4564 4565 4566 4567 4568 4569 4570 4571 4572 4573 4574 4575 4576 4577 4578 4579 4580 4581 4582 4583 4584 4585 4586 4587 4588 4589 4590 4591 4592 4593 4594 4595 4596 4597 4598 4599 4600 4601 4602 4603 4604 4605 4606 4607 4608 4609 4610 4611 4612 4613 4614 4615 4616 4617 4618 4619 4620 4621 4622 4623 4624 4625 4626 4627 4628 4629 4630 4631 4632 4633 4634 4635 4636 4637 4638 4639 4640 4641 4642 4643 4644 4645 4646 4647 4648 4649 4650 4651 4652 4653 4654 4655 4656 4657 4658 4659 4660 4661 4662 4663 4664 4665 4666 4667 4668 4669 4670 4671 4672 4673 4674 4675 4676 4677 4678 4679 4680 4681 4682 4683 4684 4685 4686 4687 4688 4689 4690 4691 4692 4693 4694 4695 4696 4697 4698 4699 4700 4701 4702 4703 4704 4705 4706 4707 4708 4709 4710 4711 4712 4713 4714 4715 4716 4717 4718 4719 4720 4721 4722 4723 4724 4725 4726 4727 4728 4729 4730 4731 4732 4733 4734 4735 4736 4737 4738 4739 4740 4741 4742 4743 4744 4745 4746 4747 4748 4749 4750 4751 4752 4753 4754 4755 4756 4757 4758 4759 4760 4761 4762 4763 4764 4765 4766 4767 4768 4769 4770 4771 4772 4773 4774 4775 4776 4777 4778 4779 4780 4781 4782 4783 4784 4785 4786 4787 4788 4789 4790 4791 4792 4793 4794 4795 4796 4797 4798 4799 4800 4801 4802 4803 4804 4805 4806 4807 4808 4809 4810 4811 4812 4813 4814 4815 4816 4817 4818 4819 4820 4821 4822 4823 4824 4825 4826 4827 4828 4829 4830 4831 4832 4833 4834 4835 4836 4837 4838 4839 4840 4841 4842 4843 4844 4845 4846 4847 4848 4849 4850 4851 4852 4853 4854 4855 4856 4857 4858 4859 4860 4861 4862 4863 4864 4865 4866 4867 4868 4869 4870 4871 4872 4873 4874 4875 4876 4877 4878 4879 4880 4881 4882 4883 4884 4885 4886 4887 4888 4889 4890 4891 4892 4893 4894 4895 4896 4897 4898 4899 4900 4901 4902 4903 4904 4905 4906 4907 4908 4909 4910 4911 4912 4913 4914 4915 4916 4917 4918 4919 4920 4921 4922 4923 4924 4925 4926 4927 4928 4929 4930 4931 4932 4933 4934 4935 4936 4937 4938 4939 4940 4941 4942 4943 4944 4945 4946 4947 4948 4949 4950 4951 4952 4953 4954 4955 4956 4957 4958 4959 4960 4961 4962 4963 4964 4965 4966 4967 4968 4969 4970 4971 4972 4973 4974 4975 4976 4977 4978 4979 4980 4981 4982 4983 4984 4985 4986 4987 4988 4989 4990 4991 4992 4993 4994 4995 4996 4997 4998 4999 5000 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 5013 5014 5015 5016 5017 5018 5019 5020 5021 5022 5023 5024 5025 5026 5027 5028 5029 5030 5031 5032 5033 5034 5035 5036 5037 5038 5039 5040 5041 5042 5043 5044 5045 5046 5047 5048 5049 5050 5051 5052 5053 5054 5055 5056 5057 5058 5059 5060 5061 5062 5063 5064 5065 5066 5067 5068 5069 5070 5071 5072 5073 5074 5075 5076 5077 5078 5079 5080 5081 5082 5083 5084 5085 5086 5087 5088 5089 5090 5091 5092 5093 5094 5095 5096 5097 5098 5099 5100 5101 5102 5103 5104 5105 5106 5107 5108 5109 5110 5111 5112 5113 5114 5115 5116 5117 5118 5119 5120 5121 5122 5123 5124 5125 5126 5127 5128 5129 5130 5131 5132 5133 5134 5135 5136 5137 5138 5139 5140 5141 5142 5143 5144 5145 5146 5147 5148 5149 5150 5151 5152 5153 5154 5155 5156 5157 5158 5159 5160 5161 5162 5163 5164 5165 5166 5167 5168 5169 5170 5171 5172 5173 5174 5175 5176 5177 5178 5179 5180 5181 5182 5183 5184 5185 5186 5187 5188 5189 5190 5191 5192 5193 5194 5195 5196 5197 5198 5199 5200 5201 5202 5203 5204 5205 5206 5207 5208 5209 5210 5211 5212 5213 5214 5215 5216 5217 5218 5219 5220 5221 5222 5223 5224 5225 5226 5227 5228 5229 5230 5231 5232 5233 5234 5235 5236 5237 5238 5239 5240 5241 5242 5243 5244 5245 5246 5247 5248 5249 5250 5251 5252 5253 5254 5255 5256 5257 5258 5259 5260 5261 5262 5263 5264 5265 5266 5267 5268 5269 5270 5271 5272 5273 5274 5275 5276 5277 5278 5279 5280 5281 5282 5283 5284 5285 5286 5287 5288 5289 5290 5291 5292 5293 5294 5295 5296 5297 5298 5299 5300 5301 5302 5303 5304 5305 5306 5307 5308 5309 5310 5311 5312 5313 5314 5315 5316 5317 5318 5319 5320 5321 5322 5323 5324 5325 5326 5327 5328 5329 5330 5331 5332 5333 5334 5335 5336 5337 5338 5339 5340 5341 5342 5343 5344 5345 5346 5347 5348 5349 5350 5351 5352 5353 5354 5355 5356 5357 5358 5359 5360 5361 5362 5363 5364 5365 5366 5367 5368 5369 5370 5371 5372 5373 5374 5375 5376 5377 5378 5379 5380 5381 5382 5383 5384 5385 5386 5387 5388 5389 5390 5391 5392 5393 5394 5395 5396 5397 5398 5399 5400 5401 5402 5403 5404 5405 5406 5407 5408 5409 5410 5411 5412 5413 5414 5415 5416 5417 5418 5419 5420 5421 5422 5423 5424 5425 5426 5427 5428 5429 5430 5431 5432 5433 5434 5435 5436 5437 5438 5439 5440 5441 5442 5443 5444 5445 5446 5447 5448 5449 5450 5451 5452 5453 5454 5455 5456 5457 5458 5459 5460 5461 5462 5463 5464 5465 5466 5467 5468 5469 5470 5471 5472 5473 5474 5475 5476 5477 5478 5479 5480 5481 5482 5483 5484 5485 5486 5487 5488 5489 5490 5491 5492 5493 5494 5495 5496 5497 5498 5499 5500 5501 5502 5503 5504 5505 5506 5507 5508 5509 5510 5511 5512 5513 5514 5515 5516 5517 5518 5519 5520 5521 5522 5523 5524 5525 5526 5527 5528 5529 5530 5531 5532 5533 5534 5535 5536 5537 5538 5539 5540 5541 5542 5543 5544 5545 5546 5547 5548 5549 5550 5551 5552 5553 5554 5555 5556 5557 5558 5559 5560 5561 5562 5563 5564 5565 5566 5567 5568 5569 5570 5571 5572 5573 5574 5575 5576 5577 5578 5579 5580 5581 5582 5583 5584 5585 5586 5587 5588 5589 5590 5591 5592 5593 5594 5595 5596 5597 5598 5599 5600 | <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
<html>
<head>
<meta http-equiv="content-type" content="text/html; charset=us-ascii">
<title>Deprecated Ghostscript features</title>
<link rel="stylesheet" type="text/css" href="gs.css" title="Ghostscript Style">
</head>
<body>
<!-- [1.0 begin visible header] ============================================ -->
<!-- [1.1 begin headline] ================================================== -->
<h1>Deprecated Ghostscript options and output devices</h1>
<!-- [1.1 end headline] ==================================================== -->
<!-- [1.2 begin table of contents] ========================================= -->
<h2>Table of contents</h2>
<blockquote><ul>
<li><a href="#Options">Deprecated Options</a>
<li><a href="#HP8_color_inkjet">H-P 8xx, 1100, and 1600 color inkjet printers</a>
<ul>
<li><a href="#HP8_gdevcd8">Drivers contained in <code>gdevcd8.c</code></a>
<li><a href="#HP8_further_documentation">Further documentation</a>
</ul>
<li><a href="#HP880_color_inkjet">H-P 812, 815, 832, 880, 882, 895, and 970 color inkjet printers</a>
<ul>
<li><a href="#HP880_gdevcd8">Drivers contained in <code>gdevcd8.c</code></a>
<li><a href="#HP880_further_documentation">Further documentation</a>
</ul>
<li><a href="#HP_color_inkjet">Other H-P color inkjet printers</a>
<ul>
<li><a href="#HP_gdevcdj">Drivers contained in <code>gdevcdj.c</code></a>
<li><a href="#HP_paper_size">Default paper size</a>
<li><a href="#HP_limits">Deskjet physical limits</a>
<li><a href="#HP_command_line">Printer properties (command-line parameters)</a>
<ul>
<li><a href="#HP_bpp">Bits per pixel</a>
<li><a href="#HP_deskjet_properties">Deskjet properties</a>
<li><a href="#HP_paintjet_properties">Paintjet XL300 / Paintjet XL properties</a>
</ul>
<li><a href="#HP_gamma">Gamma correction</a>
<li><a href="#HP_resolution_enhance">HP's resolution-enhanced mode for Inkjet printers</a>
<li><a href="#HP_tips">General tips</a>
</ul>
<li><a href="#BJC_8200">Canon BJC-8200 printer</a>
<li><a href="#BJC">Other Canon BubbleJet (BJC) printers</a>
<ul>
<li><a href="#BJC_history">History</a>
<li><a href="#BJC_build">Configuring and building the BJC drivers</a>
<ul>
<li><a href="#BJC_defaults">Modify values in <code>gdevbjc.h</code></a>
<li><a href="#BJC_CMYK_RGB">CMYK-to-RGB color conversion</a>
<li><a href="#BJC_vertical_centering">Vertical centering of the printable area</a>
<li><a href="#BJC_margins">Page margins</a>
<li><a href="#BJC_compile">Makefile and compilation</a>
</ul>
<li><a href="#BJC_usage">Use of the drivers</a>
<ul>
<li><a href="#BJC_options">Supported Options and Defaults</a>
<li><a href="#BJC_device_info">Device information</a>
<li><a href="#BJC_HW_margins">Hardware margins</a>
<li><a href="#BJC_PPD">PostScript printer description (PPD) files</a>
<li><a href="#BJC_PPD_custom">Customizing the PPD files</a>
</ul>
<li><a href="#BJC_bugs">How to report problems</a>
<li><a href="#BJC_acks">Acknowledgements</a>
</ul>
<li><a href="#STC_epson_stylus">Epson Stylus color printer (see also <code>uniprint</code>)</a>
<ul>
<li><a href="#STC_usage">Usage</a>
<li><a href="#STC_options">Options</a>
<li><a href="#STC_FAQ">Application note and FAQ</a>
<ul>
<li><a href="#STC_FAQ_A3">Support for A3 paper</a>
<li><a href="#STC_FAQ_margins">Margins, PageSize</a>
<li><a href="#STC_FAQ_II_IIS_1500">Stylus Color II / IIs and 1500</a>
</ul>
<li><a href="#STC_recommendations">Recommendations</a>
<ul>
<li><a href="#STC_dither_experiment">Color dithering experiments with <code>gdevstc</code> 1.21</a>
</ul>
<li><a href="#STC_color_transform">Color transformation</a>
<li><a href="#STC_CAM"><code>ColorAdjustMatrix</code></a>
<li><a href="#STC_RGBCMYK_coding">RGB / CMYK coding and transfer, and <code>BitsPerPixel</code></a>
<li><a href="#What_is_weaving">What is weaving?</a>
<li><a href="#STC_print_modes">Print mode parameters</a>
<ul>
<li><a href="#STC_unidirectional"><code>Unidirectional</code></a>
<li><a href="#STC_noweave"><code>Microweave</code>, <code>noWeave</code> and <code>OutputCode=deltarow</code></a>
<li><a href="#STC_model"><code>Model</code></a>
</ul>
<li><a href="#STC_Pitfalls">Bugs and pitfalls</a>
<li><a href="#STC_Tests">Tests</a>
<ul>
<li><a href="#STC_OutputCodes">The various OutputCodes</a>
<li><a href="#STC_printing_time">Printing time related to other options</a>
</ul>
<li><a href="#STC_acks">Acknowledgments</a>
</ul>
<li><a href="#Uniprint">uniprint, a flexible unified printer driver</a>
<ul>
<li><a href="#Uni_state">The state of this driver</a>
<li><a href="#Uni_background">Notes on <code>uniprint</code>'s background</a>
<li><a href="#Uni_make_pfile">Godzilla's guide to the creation of Unified Printer Parameter (<code>.upp</code>) files</a>
<li><a href="#Uni_all_parameters">All parameters in brief</a>
<li><a href="#Uni_honors"><code>Uniprint</code>'s Roll of Honor</a>
<li><a href="#Uni_weaving_howto"><code>Uniprint</code> weaving parameters howto</a></li>
<li><a href="#Uni_esc300">Extension to <code>uniprint</code> for the Epson Stylus Color 300</a></li>
</ul>
</ul></blockquote>
<!-- [1.2 end table of contents] =========================================== -->
<!-- [1.3 begin hint] ====================================================== -->
<p><strong>These devices are no longer supported and/or superceeded by newer methods.
The documentation is kept here for reference. Be advised that these devices
will be removed in future versions of Ghostscript.</strong></p>
<p>Supported devices are descripted in <a href="Devices">Details of Ghostscript
output devices</a>.</p>
<p>For other information, see the <a href="Readme.htm">Ghostscript
overview</a>. You may also be interested in <a href="Make.htm">how to
build Ghostscript</a> and <a href="Install.htm">install it</a>, as well as
the description of the <a href="Drivers.htm">driver interface</a>.
<!-- [1.3 end hint] ======================================================== -->
<hr>
<!-- [1.0 end visible header] ============================================== -->
<!-- [2.0 begin contents] ================================================== -->
<h2><a name="Options"></a>Deprecated options</h2>
<p>
For compatibility with older versions of Ghostscript, <tt>-sOUTPUTFILE</tt>
is a synonym for <tt>-sOutputFile</tt>. It should not be used in new code.
<hr>
<h2><a name="HP8_color_inkjet"></a>H-P 8xx, 1100, and 1600 color inkjet printers</h2>
<p>
This section, written by Uli Wortmann <<a
href="mailto:uliw@erdw.ethz.ch">uliw@erdw.ethz.ch</a>>, deals with the
DeskJet 670, 690, 850, 855, 870, 890, 1100, and 1600.
<h3><a name="HP8_gdevcd8"></a>Drivers contained in <code>gdevcd8.c</code></h3>
<p>
The source module <code>gdevcd8.c</code> contains four generic drivers:
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>cdj670</code>
<td>
<td>HP DeskJet 670 and 690
<tr valign=top> <td><code>cdj850</code>
<td>
<td>HP DeskJet 850, 855, 870, and 1100
<tr valign=top> <td><code>cdj890</code>
<td>
<td>HP DeskJet 890
<tr valign=top> <td><code>cdj1600</code>
<td>
<td>HP DeskJet 1600
</table></blockquote>
<h3><a name="HP8_further_documentation"></a>Further documentation</h3>
<p>
<b>Credits:</b> Much of the driver is based on ideas derived from the
cdj550 driver of George Cameron. The support for the hp670, hp690, hp890
and hp1600 was added by Martin Gerbershagen.
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td>11.11.96
<td>
<td>Version 1.0
<td>
<td>
<tr valign=top> <td>25.08.97
<td>
<td>Version 1.2
<td>
<td>Resolved all but one of the known bugs, introduced a couple of
perfomance improvements. Complete new color-transfer-function
handling (see gamma).
<tr valign=top> <td>01.06.98
<td>
<td>Version 1.3
<td>
<td>Due to the most welcome contribution of Martin Gerbershagen
(ger@ulm.temic.de), support for the hp670, hp690 and hp890 and
hp1600 has been added. Martin has also resolved all known bugs.
<tr valign=top> <td>
<td>
<td>
<td>
<td>Problems:Dark colors are still pale.
</table></blockquote>
<p>
The hp690 is supported through the hp670 device, the hp855, hp870 and the
hp1100 through the hp850 device. The driver needs no longer special
switches to be invoked except <code>-sDEVICE=cdj850</code>,
<code>-sDEVICE=CDJ890</code>, <code>-sDEVICE=CDJ670</code>, or
<code>-sDevice=CDJ1600</code>. The following switches are supported.
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>-dPapertype=</code>
<td>
<td>0
<td>
<td>plain paper [default]
<tr valign=top> <td>
<td>
<td>1
<td>
<td>bond paper
<tr valign=top> <td>
<td>
<td>2
<td>
<td>special paper
<tr valign=top> <td>
<td>
<td>3
<td>
<td>glossy film
<tr valign=top> <td>
<td>
<td>4
<td>
<td>transparency film
<tr valign=top> <td>
<td>
<td>
<td>
<td>Currently the lookup tables are unsuited for printing on
special paper or transparencies. For these please revert to the
gamma functions.
<tr valign=top> <td><code>-dQuality=</code>
<td>
<td>-1
<td>
<td>draft
<tr valign=top> <td>
<td>
<td>0
<td>
<td>normal [default]
<tr valign=top> <td>
<td>
<td>1
<td>
<td>presentation
<tr valign=top> <td><code>-dRetStatus=</code>
<td>
<td>0
<td>
<td>C-RET off
<tr valign=top> <td>
<td>
<td>1
<td>
<td>C-RET on [default]
<tr valign=top> <td><code>-dMasterGamma=</code>
<td>
<td>3.0
<td>
<td>[default = 1.0]
</table></blockquote>
<blockquote>
<b>Note:</b> To take advantage of the calibrated color-transfer functions,
be sure not to have any gamma statements left! If you need to (i.e., for
overhead transparencies), you still can use the gamma functions, but they
will override the built-in calibration. To use gamma in the traditional
way, set MasterGamma to any value greater than 1.0 and less than 10.0. To
adjust individual gamma values, you have to additionally set MasterGamma to
a value greater than 1.0 and less than 10.0. With the next release, gamma
functions will be dropped.
</blockquote>
<p>
When using the driver, be aware that printing at 600dpi involves
processing large amounts of data (> 188MB !). Therefore the
driver is not what you would expect to be a fast driver ;-)
This is no problem when printing a full-sized color page (because
printing itself is slow), but it's really annoying if you print only
text pages. Maybe I can optimize the code for text-only pages in a
later release. Right now, it is recommended to use the highest
possible optimisation level your compiler offers.
For the time being, use the cdj550 device with <code>-sBitsPerPixel=3</code>
for fast proof prints. If you simply want to print 600dpi BW data,
use the cdj550 device with <code>-sBitsPerPixel=8</code> (or 1).
<p>
Since the printer itself is slow, it may help to set the process priority
of the gs process to "regular" or even less. On a 486/100MHz this is still
sufficient to maintain a continuous data flow. Note to OS/2 users: simply
put the gs window into the background or minimize it. Also make sure that
<code>print01.sys</code> is invoked without the <code>/irq</code>
switch (great speed improvement under Warp4).
<p>
The printer default settings compensate for dot-gain by a calibrated
color-transfer function. If this appears to be too light for your business
graphs, or for overhead transparencies, feel free to set
<code>-dMasterGamma=1.7</code>. Furthermore, you may tweak the gamma
values independently by setting <code>-dGammaValC</code>,
<code>-dGammaValM</code>, <code>-dGammaValY</code> or
<code>-dGammaValK</code> (if not set, the values default to
<code>MasterGamma</code>). This will only work when
<code>-dMasterGamma</code> is set to a value greater than 1.0.
<p>
Further information, bugs, tips etc, can be found at my website. To learn
more about gamma, see
<a href="ftp://ftp.igd.fhg.de/pub/doc/colour/GammaFAQ.pdf">ftp://ftp.igd.fhg.de/pub/doc/colour/GammaFAQ.pdf</a>.
<p>
Depending on how you transfer the files, under UNIX you may need to remove
the CRs of the CR-LF sequence used for end-of-line on DOS-based (MS
Windows-based) systems. You can do this in unpacking the files with <code>unzip -a hp850.zip</code>.
<p>
To compile with gs5.x or later, simply add to your makefile
<blockquote>
DEVICE_DEVS4=cdj850.dev cdj670.dev cdj890.dev cdj1600.dev
</blockquote>
<p>
Have fun!
<p>
Uli <<a href="mailto:uliw@erdw.ethz.ch">uliw@erdw.ethz.ch</a>>
<br><a href="http://www.erdw.ethz.ch/~bonk/">http://www.erdw.ethz.ch/~bonk/</a>
<hr>
<h2><a name="HP880_color_inkjet"></a>H-P 812, 815, 832, 880, 882, 895, and 970 color inkjet printers</h2>
<p>
This section, written by Matthew Gelhaus <<a
href="mailto:hp880@gelhaus.net">hp880@gelhaus.net</a>>, deals with the
DeskJet 812, 815, 832, 880, 882, 895, and 970.
<p>
This is a modified version of the <a href="#HP8_color_inkjet">HP8xx driver</a>
written by Uli Wortmann. More information and download are available at
<a href="http://www.gelhaus.net/hp880c/">http://www.gelhaus.net/hp880c/</a>.
<h3><a name="HP880_gdevcd8"></a>Drivers contained in <code>gdevcd8.c</code></h3>
<p>
The source module <code>gdevcd8.c</code> contains one generic driver:
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>cdj880</code>
<td>
<td>HP DeskJet 812, 815, 832, 880, 882, 895, and 970
</table></blockquote>
<h3><a name="HP880_further_documentation"></a>Further documentation</h3>
<p>
<b>Credits:</b> This driver is based on the cdj850 driver by Uli Wortmann, and shares the same
internal structure, although the PCL3+ interpretation has changed.
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td>15.03.99
<td>
<td>Version 1.3
<td>
<td>Initial version, based on Version 1.3 of Uli Wortmann's driver.
<tr valign=top> <td>26.02.00
<td>
<td>Version 1.4beta
<td>
<td>Greatly improved color handling & dithering, but not yet complete enough
to use for text.
</table></blockquote>
<p>
All printers are supported through the cdj880 device. Invoke with
<code>-sDEVICE=cdj880</code>. The following switches are supported.
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>-dPapertype=</code>
<td>
<td>0
<td>
<td>plain paper [default]
<tr valign=top> <td>
<td>
<td>1
<td>
<td>bond paper
<tr valign=top> <td>
<td>
<td>2
<td>
<td>special paper
<tr valign=top> <td>
<td>
<td>3
<td>
<td>glossy film
<tr valign=top> <td>
<td>
<td>4
<td>
<td>transparency film
<tr valign=top> <td>
<td>
<td>
<td>
<td>Currently the lookup tables are unsuited for printing on
special paper or transparencies. For these please revert to the
gamma functions.
<tr valign=top> <td><code>-dQuality=</code>
<td>
<td>-1
<td>
<td>draft
<tr valign=top> <td>
<td>
<td>0
<td>
<td>normal [default]
<tr valign=top> <td>
<td>
<td>1
<td>
<td>presentation
<tr valign=top> <td><code>-dMasterGamma=</code>
<td>
<td>3.0
<td>
<td>[default = 1.0]
</table></blockquote>
<p>
The printer default settings compensate for dot-gain by a pre-defined
color-transfer function. If this appears to be too light for your business
graphs, or for overhead transparencies, feel free to set
<code>-dMasterGamma=1.7</code>. Furthermore, you may tweak the gamma
values independently by setting <code>-dGammaValC</code>,
<code>-dGammaValM</code>, <code>-dGammaValY</code> or
<code>-dGammaValK</code> (if not set, the values default to
<code>MasterGamma</code>). This will only work when
<code>-dMasterGamma</code> is set to a value greater than 1.0.
<p>
Further information, bugs, tips etc, can be found at my website.
<p>
To compile with gs6.x or later, simply add to your makefile
<blockquote>
DEVICE_DEVS4=$(DD)cdj880.dev
</blockquote>
<p>
Matthew Gelhaus <<a href="mailto:hp880@gelhaus.net">mailto:hp880@gelhaus.net</a>>
<br><a href="http://www.gelhaus.net/hp880c/">http://www.gelhaus.net/hp880c/</a>
<hr>
<h2><a name="HP_color_inkjet"></a>H-P color inkjet printers</h2>
<p>
This section, written by George Cameron, deals with the DeskJet 500C,
DeskJet 550C, PaintJet, PaintJet XL, PaintJet XL300, the DEC LJ250
operating in PaintJet-compatible mode.
<h3><a name="HP_gdevcdj"></a>Drivers contained in <code>gdevcdj.c</code></h3>
<p>
The source module <code>gdevcdj.c</code> contains six generic drivers:
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>cdj500</code>
<td>
<td>HP DeskJet 500C and 540C
<tr valign=top> <td><code>cdj550</code>
<td>
<td>HP DeskJet 550C, 560C, 660C, 660Cse
<tr valign=top> <td><code>pjxl300</code>
<td>
<td>HP PaintJet XL300, DeskJet 1200C, and CopyJet
<tr valign=top> <td><code>pjtest</code>
<td>
<td>HP PaintJet
<tr valign=top> <td><code>pjxltest</code>
<td>
<td>HP PaintJet XL
<tr valign=top> <td><code>declj250</code>
<td>
<td>DEC LJ250
</table></blockquote>
<p>
All these drivers have 8-bit (monochrome), 16-bit and 24-bit (colour) and
for the DJ 550C, 32-bit (colour, CMYK mode) options in addition to standard
colour and mono drivers. It is also possible to set various
printer-specific parameters from the command line, for example
<blockquote><code>
gs -sDEVICE=cDeskJet -dBitsPerPixel=16 -dDepletion=1 -dShingling=2 tiger.eps
</code></blockquote>
<p>
<b>Note:</b> the old names <code>cDeskJet</code>,
<code>cdjcolor</code> and <code>cdjmono</code> drivers have been
retained; however, their functionality duplicates that available using the
drivers above (and <code>cDeskJet</code> is identical to
<code>cdj500</code>). That is, we can use
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>gs -sDEVICE=cdj500 -dBitsPerPixel=24</code>
<td>
<td>for <code>cdjcolor</code>, and
<tr valign=top> <td><code>gs -sDEVICE=cdj500 -dBitsPerPixel=1</code>
<td>
<td>for <code>cdjmono</code>
</table></blockquote>
<h3><a name="HP_paper_size"></a>Default paper size</h3>
<p>
If the preprocessor symbol <code>A4</code> is defined, the default paper
size is ISO A4; otherwise it is U.S. letter size (see about
<a href="Use.htm#Known_paper_sizes">paper sizes</a> in the usage
documentation). You can <a href="Use.htm#Paper_size">specify other paper
sizes</a> on the command line, including A3 for the PaintJet XL and
PaintJet XL300, as also explained in the usage documentation.
<h3><a name="HP_limits"></a>DeskJet physical limits</h3>
<p>
The DeskJet's maximum printing width is 2400 dots, or 8 inches
(20.32cm). The printer manuals say that the maximum recommended printing
height on the page is 10.3 inches (26.16cm), but since this is obviously
not true for A4 paper, and I have been unable to detect any problems in
printing longer page lengths, this would seem to be a rather artificial
restriction.
<p>
All DeskJets have 0.5 inches (1.27cm) of unprintable bottom margin, due to the mechanical
arrangement used to grab the paper. Side margins are approximately 0.25 inches (0.64cm)
for U.S. letter paper, and 0.15 inches (0.38cm) for A4.
<h4><a name="HP_command_line"></a>Printer properties (command-line parameters)</h4>
<p>
Several printer "properties" have been implemented for these printers.
Those available so far are all integer quantities, and thus may be
specified, for instance, like
<blockquote>
<code>gs -dBitsPerPixel=32 -dShingling=1</code> ...
</blockquote>
<p>
which sets the <code>BitsPerPixel</code> parameter to 32 and the
<code>Shingling</code> parameter to 1.
<h4><a name="HP_bpp"></a>Bits per pixel</h4>
<p>
If the preprocessor symbol <code>BITSPERPIXEL</code> is defined as an
integer (see below for the range of allowable values), that number defines
the default bits per pixel (bit depth) for the generic drivers. If the
symbol is undefined, the default is 24 bits per pixel. It is, of course,
still possible to specify the value from the command line as described
below. Note also that the <code>cDeskJet</code>,
<code>cdjcolor</code> and <code>cdjmono</code> drivers are unaffected
by setting this symbol, as their default settings are predefined to be 1, 3
and 24 respectively.
<p>
All of the drivers in <code>gdevcdj.c</code> accept a command line
option to set the <code>BitsPerPixel</code> property. This gives
considerable flexibility in choosing various tradeoffs among speed,
quality, colour, etc. The valid numbers are:
<blockquote><dl compact>
<dt><b>1</b>
<dd>A standard Ghostscript monochrome driver, using black ink (by
installing the separate mono cartridge in the case of the DeskJet 500C, or
automatically for the other printers).
<dt><b>3</b>
<dd>A standard Ghostscript colour driver, using internal dithering. This
is fast to compute and to print, but the clustered dithering can lose some
detail and colour fidelity.
<dt><b>8</b>
<dd>An "error-diffusion" monochrome driver which uses Floyd-Steinberg
dithering to print greyscale images. The patterns are much more randomised
than with the normal clustered dithering, but the data files can be much
larger and somewhat slower to print.
<dt><b>16</b>
<dd>A "cheaper" version of the 24-bit driver, which generates
Floyd-Steinberg colour dithered output using the minimum memory (this may
be helpful when using Ghostscript has not been compiled using a 16-bit
build environment). The quality can be almost as good as the 24-bit
version.
<dt><b>24</b>
<dd>A high-quality colour driver using Floyd-Steinberg dithering for
maximum detail and colour range. However, it is very memory-intensive, and
thus can be slow to compute. It tends to produce rather larger raw data
files, so they can also take longer to print.
<dt><b>32</b>
<dd>Only for the DeskJet 550C, which uses the black cartridge and the
colour cartridge simultaneously (that is, CMYK printing). This printer can
both be faster and give higher quality than the DeskJet 500C, because of
the true black ink. (Note that the 24-bit mode also permits CMYK printing
on this printer, and uses less memory. Any differences between 24-bit and
32-bit should be small.)
</dl></blockquote>
<h4><a name="HP_DeskJet_properties"></a>DeskJet properties</h4>
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=bottom>
<th align=left>Name
<td>
<th align=left>Type
<td>
<th align=left>
<tr> <td colspan=5><hr>
<tr valign=top> <td><code>BlackCorrect</code>
<td>
<td><code>int</code>
<td>
<td>Colour correction to give better blacks when using the DJ500C in colour mode. For example, the default of 4 reduces the cyan component to 4/5. Range accepted: 0 - 9 (0 = none).
<tr valign=top> <td><code>Shingling</code>
<td>
<td><code>int</code>
<td>
<td>Interlaced, multi-pass printing: 0 = none, 1 = 50%, 2 = 25%, 2 is best and slowest.
<tr valign=top> <td><code>Depletion</code>
<td>
<td><code>int</code>
<td>
<td>"Intelligent" dot-removal: 0 = none, 1 = 25%, 2 = 50%, 1 best for graphics? Use 0 for transparencies.
</table></blockquote>
<h4><a name="HP_PaintJet_properties"></a>PaintJet XL300 / PaintJet XL properties</h4>
<blockquote>
<table cellpadding=0 cellspacing=0>
<tr valign=bottom>
<th align=left>Name
<td>
<th align=left>Type
<td>
<th align=left>
<tr> <td colspan=5><hr>
<tr valign=top> <td><code>PrintQuality</code>
<td>
<td><code>int</code>
<td>
<td>Mechanical print quality: -1 = fast, 0 = normal, 1 = presentation. Fast mode reduces ink usage and uses single-pass operation for some media types. Presentation uses more ink and the maximum number of passes, giving slowest printing for highest quality
<tr valign=top> <td><code>RenderType</code>
<td>
<td><code>int</code>
<td>
<td><dl compact>
<dt><b>0</b><dd>driver does dithering
<dt><b>1</b><dd>snap to primaries
<dt><b>2</b><dd>snap black to white, others to black
<dt><b>3</b><dd>ordered dither
<dt><b>4</b><dd>error diffusion
<dt><b>5</b><dd>monochrome ordered dither
<dt><b>6</b><dd>monochrome error diffusion
<dt><b>7</b><dd>cluster ordered dither
<dt><b>8</b><dd>monochrome cluster ordered dither
<dt><b>9</b><dd>user-defined dither (not supported)
<dt><b>10</b><dd>monochrome user-defined dither ns.
</dl>
</table>
<p>
The PaintJet (non-XL) has no additional properties.
</blockquote>
<h3><a name="HP_gamma"></a>Gamma correction</h3>
<p>
One consequence of using Floyd-Steinberg dithering rather than Ghostscript's
default clustered ordered dither is that it is much more obvious that the
ink dots are rather larger on the page than their nominal 1/180-inch or 1/300-inch
size (clustering the dots tends to minimise this effect). Thus it is often
the case that the printed result is rather too dark. A simple empirical
correction for this may be achieved by preceding the actual PostScript
file to be printed by a short file which effectively sets the gamma for
the device, such as
<blockquote><code>
gs ... gamma.ps colorpic.ps -c quit
</code></blockquote>
<p>
where <code>gamma.ps</code> is
<blockquote>
<pre>%!
/.fixtransfer {
currentcolortransfer 4 {
mark exch
dup type dup /arraytype eq exch /packedarraytype eq or
1 index xcheck and { /exec load } if
0.333 /exp load
] cvx 4 1 roll
} repeat setcolortransfer
} bind odef
.fixtransfer
/setpagedevice { setpagedevice .fixtransfer } bind odef</pre>
</blockquote>
<p>
This does the gamma correction <b><em>after</em></b> whatever correction
the device might be doing already. To do the correction
<b><em>before</em></b> the current correction,
<blockquote>
<pre>%!
/.fixtransfer {
currentcolortransfer 4 {
mark 0.333 /exp load 4 -1 roll
dup type dup /arraytype eq exch /packedarraytype eq or
1 index xcheck and { /exec load } if
] cvx 4 1 roll
} repeat setcolortransfer
} bind odef
.fixtransfer
/setpagedevice { setpagedevice .fixtransfer } bind odef</pre>
</blockquote>
<p>
This example sets the gamma for R, G, and B to 3, which seems to work
reasonably well in practice.
<h3><a name="HP_resolution_enhance"></a>HP's resolution-enhanced mode for Inkjet printers</h3>
<p>
This feature is available on HP's more recent inkjet printers, including
the DeskJet 520 (mono), 540 (mono or colour) and 560C (mono and colour).
The colour and monochrome drivers for the HP DeskJet 550c are (probably)
the best you will get for use with Ghostscript, for the following reasons.
<p>
These printers do not offer true 600×300dpi resolution. Those that
print in colour are strictly 300×300dpi in colour mode, while in mono
mode there is a pseudo 600×300dpi mode with the restriction that you
can't print two adjacent dots. In effect what you have is 600dpi dot
positioning, but on average you don't get more dots per line. This
provides the possibility, for instance, to have sharper character outlines,
because you can place dots on the edges nearer to their ideal positions.
This is why it is worth doing.
<p>
However, HP will not support user-level programming of this
resolution-enhanced mode, one reason being that (I understand) all the dot
spacing has to be done by the driver, and if you get it wrong, you can
actually damage the print head.
<p>
To summarise, you may lose a smidgin of (potential) text clarity using the
550c drivers (<code>cdj550</code>, <code>cdjcolor</code>,
<code>cdjmono</code> etc.), but other than that, they are the ones for
the job.
<h3><a name="HP_tips"></a>General tips</h3>
<p>
For all the printers above, the choice of paper is critically important to
the final results. The printer manuals suggest type of paper, but in
general, smoother, less fibrous types give better results. In particular,
the special ink-jet paper can make a big difference: colours are brighter,
but most importantly, there is almost no colour bleed, even with adjacent
areas of very heavy inking. Similarly the special coated transparencies
also work well (and ordinary transparencies do not work at all!).
<p>
The Unix procedure <a href="Unix-lpr.htm"><code>unix-lpr.sh</code></a>
provides one example of setting up a multi-option colour PostScript
<code>lpr</code> queue on Unix systems, and includes the ability to
choose a range of different colour options and printer accounting and error
logging.
<p>
<b>Caveat emptor!</b> It is not always easy for me to test all of these
drivers, as the only colour printer I have here is the DeskJet 500C. I rely
on others to test drivers for the additional machines and report their
findings back to me.
<hr>
<h2><a name="BJC_8200"></a>Canon BJC-8200 printer</h2>
<p>
This section was contributed by the author of the <code>uniprint</code>
configuration files for the Canon BJC-8200, Stephan C. Buchert <<a
href="mailto:scb@stelab.nagoya-u.ac.jp">scb@stelab.nagoya-u.ac.jp</a>>.
These files also handle the Japanese Canon F850 printer.
<p>
Warning: Usage of this program is neither supported nor endorsed by
the Canon corporation. Please see the Ghostscript <a
href="Public.htm">license</a> regarding warranty.
<h3>Introduction</h3>
<p>
The Canon Bubble Jet printer BJC-8200 is designed for printing digital
photos and halftone images. Software drivers for Windows 95-2000 and Mac are
usually included and can be downloaded from the Canon web sites like
<a href="http://consumer.usa.canon.com/bjc/bjc8200/">http://consumer.usa.canon.com/bjc/bjc8200/</a>
for the US market. If these drivers cannot be used for some reason, then at
present Ghostscript is probably the alternative giving the best results.
<p>
The BJC-8200 has features not found among the specs of earlier bubble jet
models (except the even more advanced BJC-8500) and is advertised to offer:
<ol>
<li>microfine droplet technology;
<li>support for printing on a new type of paper, Photo Paper Pro;
<li>a printhead capable of printing up to 1200 DpI;
<li>individual ink tanks for 6 colors;
<li>an internal status monitor reporting low ink back to a driver;
<li>an optional color scanner cartridge for up to 600 DpI resolution.
</ol>
<p>
Access to features 5 and 6 requires use of the original Canon drivers for
the foreseeable future. This README is about getting the printer features
1-3 working with Ghostscript. No (re)compilation of Ghostscript is normally
required.
<p>
Ghostscript comes with a relatively highly configurable driver, called
<a href="#Uniprint">uniprint</a>, for printers which understand raster
images in various propriety formats. Most options for this driver are
usually organized into files having the suffix ".upp." Ghostscript
versions >= 5.10 (or even earlier) include such uniprint control files
for the Canon BJC-610. They work also well for some other Canon Bubble
Jet models, for example for my BJC-35vII. But when using them for a
BJC-8200 the result is unsatisfactory.
<h3>The uniprint control files for the BJC-8200</h3>
<p>
After some experimenting with the options for uniprint I have obtained quite
satisfactory prints with my printer(*). This distribution includes six new
uniprint control files:
<ul>
<li>bj8pp12f.upp
<li>bj8hg12f.upp
<li>bj8gc12f.upp
<li>bj8oh06n.upp
<li>bj8ts06n.upp
<li>bj8pa06n.upp
</ul>
<p>
They are included in Ghostscript >=6.21. For older versions you can put
them anywhere in the Ghostscript search path (type "gs -h" to see the
path), but should perhaps add the files to the directory with the
other *.upp files. This is "/usr/share/ghostscript/gs6.01/lib" in my
RedHat 6.1 Linux box with Aladdin Ghostscript 6.01.
<p>
Here is an explanation of my file name convention: the prefix "bj8" should
perhaps be used for the Canon BJC-8200 and compatible (like the Japanese
F850 and perhaps the non-Japanese BJC-8500) models. The next two letters
indicate the print media:
<ul>
<li>pp "Photo Paper Pro"
<li>hg "High Gloss Photo Film"
<li>gc "Glossy Photo Cards"
<li>oh "OHP transparencies"
<li>ts "T-shirt transfer"
<li>pa "Plain Paper"
</ul>
<p>
The numbers at positions 6 and 7 indicate the resolution
<ul>
<li>12 1200x1200 DpIxDpI
<li>06 600x600 DpIxDpI
</ul>
<p>
The last letter stands for a quality factor that effects also the print
speed (presumably related to the number of passes that the printhead makes).
<ul>
<li>f highest quality
<li>n normal quality
</ul>
<p>
Printing a postcard size (~10x15 cm^2) image at 1200x1200 DpI^2 takes about
3 minutes. The output of Ghostscript is then typically 4-5 MByte. The
bootleneck seems to be the transfer of the raster image in run-length
encoded Canon format to the printer (via the parallel port on my system) or
the printer's speed, not Ghostscript or the uniprint renderer.
<h3>Further Optimization for the Canon BJC-8200</h3>
So far I have only experimented with the printer initialization code at the
beginning of each page (-dupBeginPageCommand) and the resolution (-r). Other
options, particularly the transfer arrays (-dupBlackTransfer,
-dupCyanTransfer, -dupMagentaTransfer, -dupYellowTransfer) and the margins
(-dupMargins) were simply copied from the files for the BJC-610, but they
may need to be changed for optimized performance.
<p>
Here is information useful for changing or adding uniprint control files for
the BJC-8200:
<p>
In "-dupBeginPageCommand=..." use the line
<blockquote>
1b28 64 0400 04b0 04b0
</blockquote>
<p>
for 1200x1200 resolution, and
<blockquote>
1b28 64 0400 0258 0258
</blockquote>
<p>
for 600x600. The "-r" option in the control file must of course match this
line. Other resolutions might work as well, but I didn't try.
<p>
Crucial are the numbers in the lines like
<blockquote><pre>
1b28 63 0300 3005 04
^ ^
Plain Paper 0 4 Highest quality
OHP transparency 2 .
T-shirt transfer 3 .
Glossy Photo Film 5 .
High Gloss Paper 6 0 Lowest quality
Photo Paper Pro 9
</pre></blockquote>
<h3>Outlook</h3>
<p>
Presently uniprint can use the black (K), cyan (C), magenta (M), and
yellow (Y) colors in the BJC-8200. The unused colors are photo (or
light) cyan (c) and magenta (m). Also the Canon driver seems to use
only CMYK, for example when printing on Photo Paper Pro in "Camera" or
"SuperPhoto" mode. These modes supposedly produce prints of the best
quality that the Canon driver can offer. Other modes of Canon driver
do use up to all six color cartridges (CMYKcm). Therefore expanding
uniprint's capabilities for six colors would be interesting, but it may
not increase the output quality of 6-color printers such as the
BJC-8200 drastically.
<p>
More control files for uniprint could be added in order to offer more
versatility for controlling the BJC-8200 within a Ghostscript
installation. The number of possible combinations for media type, resolution
and print quality factor is very large, many combinations would not make
much sense, many might be used here and there, but relatively rarely. The
user would have to remember a name for each combination that is used.
<p>
A better way would be to let the user patch optionally a user owned or
system wide uniprint control file before each print via some print
tool. This is similar to the approach taken by Canon with their driver for
Windows. Similarly a uniprint tool could also incorporate other functions
such as printing test and demo pages and the low ink warning once the
protocol for this is known. Clearly it would be difficult to code such a
uniprint tool for all the platforms where Ghostscript is running.
<h3>Usage on RedHat Linux</h3>
<p>
In order to install a BJC-8200 printer on a RedHat Linux system with
RedHat's printtool, you need also to insert with a text editor the contents
of the file <code>bj8.rpd</code> into the RedHat printer database
<code>/usr/lib/rhs/rhs-printfilters/printerdb</code>. Insert it most
appropriately after the section
<blockquote><pre>
StartEntry: U_CanonBJC610
.
.
.
EndEntry
< --- insert here "bj8.rpd" from this distribution:
< --- StartEntry: U_CanonBJC8200
.
.
.
</pre></blockquote>
<h3>Contacting the Author</h3>
<p>
E-mail address: <<a
href="mailto:scb@stelab.nagoya-u.ac.jp">scb@stelab.nagoya-u.ac.jp</a>>
<p>
Footnotes:
<p>
(*) Actually I have a F850, not a BJC-8200. That model is sold for the
Japanese market only. The specs and also the external look are the
same as those of the BJC-8200 models for the American and European
markets. I expect that the raster image mode which is used exclusively
by Ghostscript is entirely compatible for both models.
<p>
Stephan C. Buchert
<hr>
<h2><a name="BJC"></a>Other Canon BubbleJet (BJC) printers</h2>
<p>
This section was contributed by the author of the drivers, Yves Arrouye
(<<a href="mailto:yves.arrouye@usa.net">yves.arrouye@usa.net</a>>, but
please do not send questions to him: he no longer maintains these drivers.)
The drivers handle Canon BJC-600, BJC-4xxx, BJC-70, Stylewriter 2x00, and
BJC-800 printers.
<h3><a name="BJC_history"></a>History</h3>
<p>
The BJC-600 driver was written in the first place by Yoshio Kuniyoshi and
later modified by Yves Arrouye. We tried to make it evolve synchronously,
though Yoshio cannot be reached since a long time ago. The drivers are
based on code for the HP printers by George Cameron (in fact, they are in
the same file!), so he's the first person to thank.
<p>
The 2.00 version of the drivers was a complete rewrite of the driver
(arguments, optimization, colour handling, in short: everything!) by Yves
Arrouye. That release was also the first one to be able to use the full
width of an A3 paper size. PostScript Printer Description (PPD) files for
the drivers were released with version 2.15. They are incomplete,
but they can be used to drive the printers' main features.
<h3><a name="BJC_build"></a>Configuring and building the BJC drivers</h3>
<h4><a name="BJC_defaults"></a>Modify values in
<code>gdevbjc.h</code></h4>
<p>
Configure the drivers by modifying the default values in the file
<code>gdevbjc.h</code> or on the compilation line. If you don't do
that, the drivers use reasonable defaults that make them work "as
expected". All default values shown here are defined in that file.
<h4><a name="BJC_CMYK_RGB"></a>CMYK-to-RGB color conversion</h4>
<p>
By default, the drivers use the same algorithm as Ghostscript to convert
CMYK colors to RGB. If you prefer to use Adobe formulas, define
<code>USE_ADOBE_CMYK_RGB</code> when compiling. (See the top of the
file <code>gdevcdj.c</code> to see the difference between the two.)
<h4><a name="BJC_vertical_centering"></a>Vertical centering of the
printable area</h4>
<p>
The drivers center the imageable area horizontally but not vertically, so
that what can be printed does use the most of the output media. If you
define <code>BJC_DEFAULT_CENTEREDAREA</code> when compiling, then the
top and bottom margins will be the same, resulting in a (smaller)
vertically centered imageable area also.
<h4><a name="BJC_margins"></a>Page margins</h4>
<p>
If you define <code>USE_RECOMMENDED_MARGINS</code>, then the top and
bottom margins will be the same (that is,
<code>BJC_DEFAULT_CENTEREDAREA</code> will be defined for you) and the
margins will be the 12.4mm recommended by Canon. Since margins are
complicated (because one must rely on the mechanical precision of the
printer), the drivers do something about the bottom margin: by default the
bottom margin is 9.54mm for the BJC-600 driver and 7mm for the BJC-800. If
you define <code>USE_TIGHT_MARGINS</code>, then the bottom margin is 7mm
for both drivers (but I never managed to get my own BJC-600 to print a line
on this low bound, hence the larger default). Regardless of the presence
of this definition, <code>USE_FIXED_MARGINS</code> will not allow the
BJC-800 to use the lower 7mm bottom margin, so if you have a problem with
the bottom margin on a BJC-800, just define that (without defining
<code>USE_TIGHT_MARGINS</code>, of course).
<p>
A quick way to be sure the margins you selected is to print a file whose
contents are:
<blockquote><code>
%!<br>
clippath stroke showpage
</code></blockquote>
<p>
If the margins are okay, you will get a rectangle visibly surrounding
the printable area. If they're not correct, one or more of the sides will
be either incomplete or completely unprinted.
<h4><a name="BJC_compile"></a>Makefile and compilation</h4>
<p>
Make sure the <code>bjc600</code> or <code>bjc800</code> devices are
in <a href="Make.htm#Features_and_devices"><code>DEVICE_DEVS</code> in
the makefile</a>; that is, look in the makefile for your platform and add
them if necessary -- they may already be there. As of Ghostscript 5.10,
for instance, one makefile has
<blockquote><code>
DEVICE_DEVS6=bj10e.dev bj200.dev bjc600.dev bjc800.dev
</code></blockquote>
<h3><a name="BJC_usage"></a>Use of the drivers</h3>
<p>
There are two drivers here. The "<code>bjc600</code>" one supports the BJC-600 and
BJC-4xxx (maybe the BJC-70 as well) and the "<code>bjc800</code>" one supports the
BJC-800 series. Remarks here that apply to both drivers use the name
"bjc".
<h4><a name="BJC_options"></a>Supported Options and Defaults</h4>
<p>
Note: "options", "properties", and "parameters" designate the same thing:
device parameters that you can change.
<p>
Giving an option an incorrect value causes an error. Unless stated
otherwise, this error will be a rangecheckerror. Options may be set from
the Ghostscript command line (using the <code>-d</code> and
<code>-s</code> switches or other predetermined switches if they have an
effect on the driver) or using the PostScript Level 2
<code>setpagedevice</code> operator if Ghostscript has been compiled
with the <code>level2</code> or <code>level3</code> device (which it should
<code>;-)</code>). There are <b>no</b> special-purpose operators such as
one was able to find in Level 1 printers.
<p>
The bjc uses 24 bits per pixel by default (unless you change the value of
<code>BJC_BITSPERPIXEL</code>), corresponding to CMYK printing.
Supported modes are 1 bpp and 4 bpp (gray levels), 8 bpp, 16 bpp, 24 bpp
and 32 bpp (colours). Colours are preferably stored in the CMYK model
(which means, for example, that with 16 bpp there are only 16 different
shades of each color) but it is possible to store them as RGB color for
some depths. Some modes do Floyd-Steinberg dithering and some don't, but
use the default Ghostscript halftoning (in fact, when halftoning is used,
dithering takes also place but because of the low point density it is
usually not efficient, and thus invisible).
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=5 bgcolor="#CCCC00"><hr><font size="+1">Descriptions of printing modes by bpp and <code>Colors</code></font><hr>
<tr valign=bottom>
<th align=left>bpp
<td>
<th align=left><code>Colors</code>
<td>
<th align=left>Mode
<tr> <td colspan=5><hr>
<tr valign=top> <td>32
<td>
<td align=center>4
<td>
<td>CMYK colour printing, Floyd-Steinberg dithering
<tr valign=top> <td>24
<td>
<td align=center>4
<td>
<td>The same. (But each primary colour is stored on 6 bits instead of 8.)
<tr valign=top> <td>24
<td>
<td align=center>3
<td>
<td>RGB colour printing, Floyd-Steinberg dithering. This mode does
<code>not</code> use the black cartridge (that's why it
exists, for when you don't want to use it <code>;-)</code>).
Each primary colour is stored in 8 bits as in the 32/4 mode,
but black generation and under-color removal are done on the
driver side and not by Ghostscript, so you have no control over
it. (This mode is no longer supported in this driver.)
<tr valign=top> <td>16
<td>
<td align=center>4
<td>
<td>CMYK colour printing, halftoned by Ghostscript. F-S dithering
is still visible here (but the halftone patterns are visible
too!).
<tr valign=top> <td>8
<td>
<td align=center>4
<td>
<td>The same. (But each primary colour is stored in 2 bits instead of 4.)
<tr valign=top> <td>8
<td>
<td align=center>3
<td>
<td>RGB colour printing. This mode is not intended for use. What I
mean is that it should be used only if you want to use custom
halftone screens <b>and</b> the halftoning is broken using the
8/4 mode (some versions of Ghostscript have this problem).
<tr valign=top> <td>8
<td>
<td align=center>1
<td>
<td>Gray-level printing, Floyd-Steinberg dithering
<tr valign=top> <td>1
<td>
<td align=center>1
<td>
<td>Gray-level printing halftoned by Ghostscript
</table></blockquote>
<p>
These modes are selected using the <code>BitsPerPixel</code> <b>and</b>
<code>Colors</code> integer options (either from the command line or in
a PostScript program using <code>setpagedevice</code>). See below.
<p>
A note about darkness of what is printed: Canon printers do print dark,
really. And the Floyd-Steinberg dithering may eventually darken your image
too. So you may need to apply gamma correction by calling Ghostscript as in
<blockquote><code>
gs -sDEVICE=bjc600 gamma.ps myfile.ps
</code></blockquote>
<p>
where <code>gamma.ps</code> changes the gamma correction (here to 3 for
all colors); 0.45 gives me good results, but your mileage may vary. The
bigger the value the lighter the output:
<blockquote><code>
{ 0.45 exp } dup dup currenttransfer setcolortransfer
</code></blockquote>
<p>
The drivers support printing at 90dpi, 180dpi and 360dpi. Horizontal and
vertical resolutions must be the same or a limitcheck error will happen. A
rangecheck will happen too if the resolution is not
90 ×2^<small><sup><b>N</b></sup></small>. If the driver
is compiled with <code>-DBJC_STRICT</code> a rangecheck also happens if
the resolution is not one of those supported. This is not the case, as we
expect that there may be a 720dpi bjc some day.
<p>
Here are the various options supported by the bjc drivers, along with
their types, supported values, effects, and usage:
<dl>
<dt><code>BitsPerPixel</code> (int)
<dd>Choose the depth of the page. Valid values are 1, 8, 16, 24 (the
default) and 32.
<p>
Note that when this is set for the first time, the <code>Colors</code>
property is automatically adjusted unless it is also specified. The table
here shows the corresponding color models and the rendering method visible:
"GS" for Ghostscript halftoning and "F-S" for Floyd-Steinberg dithering.
When both are present it means that the dithering of halftones is visible.
Default choices are indicated by asterisk "*".
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=9 bgcolor="#CCCC00"><hr><font size="+1">Valid <code>Colors</code> values for<br>allowed <code>BitsPerPixel</code> values
</font><hr>
<tr valign=bottom>
<th align=left>bpp
<td>
<th align=left><code>Colors</code>
<td>
<th align=left>
<td>
<th align=left>Color model
<td>
<th align=left>Dithering
<tr> <td colspan=9><hr>
<tr valign=top> <td>32
<td>
<td align=center>4
<td>
<td>
<td align=center>
<td>CMYK
<td>
<td>F-S
<tr valign=top> <td>24
<td>
<td align=center>4
<td>
<td><b>*</b>
<td align=center>
<td>CMYK
<td>
<td>F-S
<tr valign=top> <td>
<td>
<td align=center>3
<td>
<td>
<td align=center>
<td>RGB
<td>
<td>F-S
<tr valign=top> <td>16
<td>
<td align=center>4
<td>
<td>
<td align=center>
<td>CMYK
<td>
<td>GS, F-S
<tr valign=top> <td>8
<td>
<td align=center>4
<td>
<td><b>*</b>
<td align=center>
<td>CMYK
<td>
<td>GS
<tr valign=top> <td>
<td>
<td align=center>3
<td>
<td>
<td align=center>
<td>RGB
<td>
<td>GS
<tr valign=top> <td>
<td>
<td align=center>1
<td>
<td>
<td align=center>
<td>K (CMYK)
<td>
<td>F-S
<tr valign=top> <td>1
<td>
<td align=center>1
<td>
<td><b>*</b>
<td align=center>
<td>K (CMYK)
<td>
<td>GS
</table></blockquote>
<p>Also note that automagical change of one parameter depending on the
other one does not work in a <code>setpagedevice</code> call. This
means that if you want to change <code>BitsPerPixel</code> to a value
whose valid <code>Colors</code> values do not include the actual
<code>Colors</code> value, you must change <code>Colors</code> too.
</dl>
<dl>
<dt><code>Colors</code> (int)
<dd>Choose the number of color components from among 1, 3 and 4 (the
default). This setting cannot be used in a PostScript program, only on
Ghostscript's command line. See <code>ProcessColorModel</code> below
for what to use to change the number of colors with PostScript code.
<p>
Note that setting this property does limit the choices of
<code>BitsPerPixel</code>. As for the previous property, its first
setting may induce a setting of the "other value"
(<code>BitsPerPixel</code> here). The table here indicates valid
combinations with "V", default values with asterisk "*".
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=13 bgcolor="#CCCC00"><hr><font size="+1">Valid <code>BitsPerPixel</code> values<br>for allowed <code>Colors</code> values</font><hr>
<tr valign=top> <td>
<td>
<td>
<td>
<th align=left colspan=9><code>BitsPerPixel</code> OK values<hr>
<tr valign=top> <th>Colors
<td>
<th>Type
<td>
<td>32
<td>
<td>24
<td>
<td>16
<td>
<td>8
<td>
<td>1
<tr> <td colspan=13><hr>
<tr valign=top> <td>4
<td>
<td>CMYK
<td>
<td><b>V</b>
<td>
<td><b>*</b>
<td>
<td><b>V</b>
<td>
<td><b>V</b>
<td>
<td>
<tr valign=top> <td>3
<td>
<td>RGB
<td>
<td>
<td>
<td><b>*</b>
<td>
<td>
<td>
<td><b>V</b>
<td>
<td>
<tr valign=top> <td>1
<td>
<td>K
<td>
<td>
<td>
<td>
<td>
<td>
<td>
<td><b>V</b>
<td>
<td><b>*</b>
</table></blockquote>
<p>Also note that automagical change of one parameter depending on the
other one does not work in a <code>setpagedevice</code> call. This
means that if you want to change <code>Colors</code> to a value whose
valid <code>BitsPerPixel</code> values don't include the actual
<code>BitsPerPixel</code> value, you must change
<code>BitsPerPixel</code> too.
</dl>
<dl>
<dt><code>ProcessColorModel</code> (symbol)
<dd>A symbol taken from <code>/DeviceGray</code>,
<code>/DeviceRGB</code> or <code>/DeviceCMYK</code> which can be used
to select 1, 3 or 4 colors respectively. Note that this parameter takes
precedence over <code>Colors</code>, and that both affect the same
variable of the driver. (See <code>Colors</code> above for values
combined with <code>BitsPerPixel</code>.)
</dl>
<dl>
<dt><code>HWResolution</code> (floats array)
<dd>An array of two floats giving the horizontal and vertical resolution in
dots per inch from among 90, 180 and 360 (the default). Both values must
be the same. On the Ghostscript command line, the resolution may be
changed with the <a href="Use.htm#Resolution_switch"><code>-r</code>
switch</a>.
</dl>
<dl>
<dt><code>ManualFeed</code> (bool)
<dd>Indicate that the sheets won't be fed automatically by the printer,
<code>false</code> by default. (Not meaningful on the BJC-600, I fear.)
</dl>
<dl>
<dt><code>MediaType</code> (string)
<dd>The media to print on, chosen from among "<code>PlainPaper</code>",
"<code>CoatedPaper</code>", "<code>TransparencyFilm</code>",
"<code>Envelope</code>", "<code>Card</code>" and
"<code>Other</code>". Default is "<code>PlainPaper</code>". For
"<code>Envelope</code>", "<code>Card</code>" or
"<code>Other</code>" the driver puts the printer into thick mode
automatically regardless of the actual media weight.
</dl>
<dl>
<dt><code>MediaWeight</code> (int or null)
<dd>The weight of the media in grams per square meter. Null (the default)
indicates that the weight is of no importance. If the specified media
weight is greater than 105 (that is, the value of the compilation default
<code>BJC</code>???<code>_MEDIAWEIGHT_THICKLIMIT</code>) then the
printer will be set to use thick paper.
</dl>
<dl>
<dt><code>PrintQuality</code> (string)
<dd>The quality of printing.
<table cellpadding=0 cellspacing=0>
<tr valign=bottom>
<th align=left>Value
<td>
<th align=left><code>bjc600</code>
<td>
<th align=left><code>bjc800</code>
<td>
<th align=left>
<tr> <td colspan=7><hr>
<tr valign=top> <td><code>Low</code>
<td>
<td>
<td>
<td align=center><b>X</b>
<td>
<td>Has the effect of making only two printing passes instead of four, so should be twice the speed; known as "CN" (Color Normal) mode
<tr valign=top> <td><code>Draft</code>
<td>
<td align=center><b>X</b>
<td>
<td align=center><b>X</b>
<td>
<td>Unlights the "HQ" light on a BJC-600
<tr valign=top> <td><code>Normal</code>
<td>
<td align=center><b>X</b>
<td>
<td align=center><b>X</b>
<td>
<td>Default for both drivers; lights the "HQ" light on a BJC-600
<tr valign=top> <td><code>High</code>
<td>
<td align=center><b>X</b>
<td>
<td align=center><b>X</b>
<td>
<td>Means 200% black and 100% CMY; lights the "Bk+" light on a BJC-600
</table>
</dl>
<dl>
<dt><code>DitheringType</code> (string)
<dd>Dithering algorithm from between "<code>Floyd-Steinberg</code>" and
"<code>None</code>". "<code>None</code>" is the default for 1/1 print
mode, "<code>Floyd-Steinberg</code>" for other modes. At the moment
this parameter is read-only, though no error is generated if one tries to
change it. This parameter is not of much value at the moment and is here
mainly to reserve the name for future addition of dithering algorithms.
</dl>
<dl>
<dt><code>PrintColors</code> (int)
<dd>Mask for printing color. If 0, use black for any color; otherwise the
value must be the sum of any of 1 (cyan), 2 (magenta), 4 (yellow) and 8
(black), indicating which colors will be used for printing. When printing
colour, only colours specified will be printed (this means that some planes
will be missing if a color's value above is omitted). When printing grays,
black is used if it is present in the <code>PrintColors</code>;
otherwise, the image is printed by superimposing each requested color.
</dl>
<dl>
<dt><code>MonochromePrint</code> (bool)
<dd><b>For <tt>bjc600</tt> only</b>, <code>false</code> by default.
Substitute black for Cyan, Magenta and Yellow when printing -- useful, for
example, to get some monochrome output of a dithered printing This is a
hardware mechanism as opposed to the previous software one. I think that
using this or setting <code>PrintColors</code> to 0 will give the same
results.
</dl>
<p>
Note that the <code>MediaType</code> and <code>ThickMedia</code>
options will be replaced by the use of the device
<code>InputAttributes</code> and <code>OutputAttributes</code> as
soon as possible. Please note too that the print mode may be reset at the
start of printing, not at the end. This is the expected behaviour. If you
need to reset the printer to its default state, simply print a file that
does just a <code>showpage</code>.
<h4><a name="BJC_device_info"></a>Device information</h4>
<p>
Here is other information published by the driver that you will find
in the <code>deviceinfo</code> dictionary.
<dl>
<dt><code>OutputFaceUp</code> (bool)
<dd>This has the boolean value <code>true</code>, indicating that the
sheets are stacked face up.
</dl>
<dl>
<dt><code>Version</code> (float)
<dd>In the form <b>M.</b><em>mm</em>pp, where <b>M</b> is the major
version, <em>mm</em> the bjc driver's minor version, and pp the specific
driver minor version (that is, <code>M.</code><em>mm</em> will always be
the same for the <code>bjc600</code> and <code>bjc800</code>
drivers).
</dl>
<dl>
<dt><code>VersionString</code> (string)
<dd> A string showing the driver version and other indications. At the
moment, things like "a" or "b" may follow the version to indicate alpha or
beta versions. The date of the last change to this version is given in the
form MM/DD/YY (no, it won't adapt to your locale).
</dl>
<h4><a name="BJC_HW_margins"></a>Hardware margins</h4>
<p>
The BJC printers have top and bottom hardware margins of 3mm and 7.1mm
respectively (Canon says 7mm, but this is unusable because of the rounding
of paper sizes to PostScript points). The left margin is 3.4mm for A4 and
smaller paper sizes, 6.4mm for U.S. paper sizes, envelopes and cards. It
is 4.0mm for A3 paper on the BJC-800.
<p>
The maximum printing width of a BJC-600 printer is 203mm. The maximum
printing width of a BJC-800 printer is 289mm on A3 paper, 203mm on
U.S. letter and ISO A4 paper.
<h4><a name="BJC_PPD"></a>PostScript printer description (PPD) files</h4>
<p>
The files <code>CBJC600.PPD</code> and <code>CBJC800.PPD</code> (whose
long names are, respectively, <code>Canon_BubbleJetColor_600.ppd</code>
and <code>Canon_BubbleJetColor_800.ppd</code>) are PPD files to drive the
features of the <code>bjc600</code> and <code>bjc800</code> drivers.
They can be used, for example, on NextStep systems (presumably on OpenStep
systems too) and on Unix systems with Adobe's TranScript and
<code>pslpr</code> (not tested). The files are not complete at the
moment. Please note that NextStep's printing interface does not
correctly enforce constraints specified in these files (in UIConstraints
descriptions): you must force yourself to use valid combinations of
options.
<h4><a name="BJC_PPD_custom"></a>Customizing the PPD files</h4>
<p>
By default the PPD files are set for U.S. letter size paper, and they use a
normalized transfer function. If you choose to use A4 printing by default,
you must replace "<code>Letter</code>" with "<code>A4</code>" in
these (noncontiguous) lines:
<blockquote>
[...]<br>
<code>*DefaultPageSize: Letter<br></code>
[...]<br>
<code>*DefaultRegion: Letter<br></code>
[...]<br>
<code>*DefaultImageableArea: Letter</code><br>
[...]<br>
</blockquote>
<p>
Some versions of Ghostscript have problems with normalized colors, which
makes them add magenta in gray levels. If you experience this problem,
in the PPD file replace the line
<blockquote><code>
*DefaultTransfer: Normalized
</code></blockquote>
<p>
with the alternate line
<blockquote><code>
*DefaultTransfer: Null
</code></blockquote>
<p>
The "thick media" option is implemented by choosing a value of 120 or 80
(for thick and thin media respectively) for the <code>MediaWeight</code>
feature of the drivers. If you ever change the threshold for thick media
in the driver code, you may need to change the values in the PPD files too.
<p>
All customization should be done using the "<code>*Include:</code>"
feature of PPD files so that your local changes will be retained if you
update the PPD files.
<h3><a name="BJC_bugs"></a>How to report problems</h3>
<p>
Yves Arrouye no longer maintains this driver, and will not answer questions
about it. If you are posting a question about it in a public form, please
be as descriptive as possible, and please send information that can be used
to reproduce the problem. Don't forget to say which driver you use, and in
what version. Version information can be found in the source code of the
driver or by issuing the following command in a shell:
<blockquote><code>
echo "currentpagedevice /VersionString get ==" | gs -q -sDEVICE=bjc600 -
</code></blockquote>
<h3><a name="BJC_acks"></a>Acknowledgements</h3>
<p>
I am particularly grateful to Yoshio Kuniyoshi <<a
href="mailto:yoshio@nak.math.keio.ac.jp">yoshio@nak.math.keio.ac.jp</a>>
without whom I'd never make these drivers, and also to L. Peter Deutsch,
who answered all my (often silly) questions about Ghostscript's driver
interface.
<p>
Thanks also to the people who volunteered to beta-test the v2.x BJC
drivers: David Gaudine
<<a href="mailto:david@donald.concordia.ca">david@donald.concordia.ca</a>>,
Robert M. Kenney <<a href="mailto:rmk@unh.edu">rmk@unh.edu</a>>,
James McPherson
<<a href="mailto:someone@erols.com">someone@erols.com</a>>
and Ian Thurlbeck
<<a href="mailto:ian@stams.strath.ac.uk">ian@stams.strath.ac.uk</a>>
(listed alphabetically) were particularly helpful by discovering bugs and
helping find out exact paper margins on printers I don't have access to.
<p>
And many thanks to Klaus-Gunther Hess
<<a href="mailto:ghess@elmos.de">ghess@elmos.de</a>> for looking
at the dithering code and devising a good CMYK dithering algorithm for the
Epson Stylus Color, which I then adapted to the code of these drivers.
<hr>
<h2><a name="STC_epson_stylus"></a>Epson Stylus color printer (see also <code>uniprint</code>)</h2>
<p>
This section was contributed by Gunther Hess
<<a href="mailto:ghess@elmos.de">ghess@elmos.de</a>>, who also wrote
<code>uniprint</code>, a later set of drivers. You should probably see
the section on <a href="#Uniprint"><code>uniprint</code></a> for whether
it might be better for your uses than this driver.
<h3><a name="STC_usage"></a>Usage</h3>
<p>
This driver is selected with "<code>-sDEVICE=stcolor</code>", producing
output for an Epson Stylus Color at 360dpi resolution by default. But it
can do much more with this printer, and with significantly better quality,
than with the default mode; and it can also produce code for monochrome
versions of the printer. This can be achieved via either command-line
options or Ghostscript input. For convenience a PostScript file is
supplied for use as an initial input file. Try the following command:
<blockquote>
<code>gs -sDEVICE=stcolor -r</code><b>{Xdpi}</b><code>x</code><b>{Ydpi}</b><code> stcolor.ps</code> <b>{YourFile.ps}</b>
</blockquote>
<p>
where <b>{Xdpi}</b> is one of 180, 360, or 720 and <b>{Ydpi}</b> is one of
90, 180, 360, or 720. The result should be significantly better. You may
use <code>stcolor.ps</code> with other devices too, but I do not
recommend this, since it does nothing then. <code>stcolor.ps</code>
should be available with binary distributions and should reside in the same
directory as other Ghostscript initialization files or in the same
directory as the files to be printed. Thus if Ghostscript is part of your
printer-spooler, you can insert
<blockquote><code>
(stcolor.ps) findlibfile { pop run } if pop
</code></blockquote>
<p>
in files you want to use the improved algorithms. You may want to adapt
<code>stcolor.ps</code> file to your specific needs. The methods and
options for this are described here, but this description is restricted to
Ghostscript options, while their manipulation at the PostScript level is
documented in the material on <a href="Language.htm">the relationship of
Ghostscript and PostScript</a> and in <code>stcolor.ps</code>.
<h3><a name="STC_options"></a>Options</h3>
<p>
Now to explain the options (as written on my UNIX system). The order is
somehow related to their use during the printing process:
<dl>
<dt><code>-dUnidirectional</code>
<dd>Force unidirectional printing, recommended for transparencies
</dl>
<dl>
<dt><code>-dMicroweave</code>
<dd>Enable the printer's "microweave" feature; see
"<a href="#What_is_weaving">What is weaving?</a>" below.
</dl>
<dl>
<dt><code>-dnoWeave</code>
<dd>Disable any Weaving (overrides <code>-dMicroweave</code>)
</dl>
<dl>
<dt><code>-dSoftweave</code>
<dd>Enable the driver's internal weaving. Note that <code>Softweave</code> works <b>only</b> with the original Stylus Color and the PRO-Series.
</dl>
<dl>
<dt><code>-sDithering=</code><em>{name}</em>
<dd>Select another dithering algorithm (name) from among
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>gscmyk</code>
<td>
<td>fast color output, CMYK process color model (default)
<tr valign=top> <td><code>gsmono</code>
<td>
<td>fast monochrome output
<tr valign=top> <td><code>gsrgb</code>
<td>
<td>fast color output, RGB process color model
<tr valign=top> <td><code>fsmono</code>
<td>
<td>Floyd-Steinberg, monochrome
<tr valign=top> <td><code>fsrgb</code>
<td>
<td>Floyd-Steinberg, RGB process color model (almost identical to the <code>cdj550</code>/<code>bjc</code> algorithm)
<tr valign=top> <td><code>fsx4</code>
<td>
<td>Floyd-Steinberg, CMYK process color model (shares code with <code>fsmono</code> and <code>fsrgb</code>, but is algorithmically really bad)
<tr valign=top> <td><code>fscmyk</code>
<td>
<td>Floyd-Steinberg, CMYK process color model and proper modifications for CMYK
<tr valign=top> <td><code>hscmyk</code>
<td>
<td>modified Floyd-Steinberg with CMYK model ("hs" stands for "hess" not for "high speed", but the major difference from <code>fscmyk</code> is speed)
<tr valign=top> <td><code>fs2</code>
<td>
<td>algorithm by Steven Singer (RGB) should be identical to <code>escp2cfs2</code>.
</table></blockquote>
</dl>
<dl>
<dt><code>-dBitsPerPixel=</code><em>{1...32}</em>
<dd>number of bits used for pixel storage; the larger the value, the better
the quality -- at least in theory. In <code>fsrgb</code> one can gain
some speed by restricting to 24 bits rather than the default 30.
</dl>
<dl>
<dt><code>-dFlag0</code>
<dd>causes some algorithms to select a uniform initialisation rather than a
set of random values. May yield a sharper image impression at the cost of
dithering artifacts. (Applies to <code>hscmyk</code> and all fs modes,
except for fs2, which always uses a constant initialization.)
</dl>
<dl>
<dt><code>-dFlag1</code> ... <code>-dFlag4</code>
<dd>Available for future algorithms.
</dl>
<dl>
<dt><code>-dColorAdjustMatrix='{</code><em>three, nine, or sixteen
floating-point values</em><code>}'</code>
<dd>This is a matrix to adjust the colors. Values should be between -1.0
and 1.0, and the number of values depends on the color model the selected
algorithm uses. In RGB and CMYK modes a matrix with 1.0 on the diagonal
produces no transformation. This feature is really required, but I could
not identify a similar feature at the language level, so I implemented it,
but I don't know reasonable values yet.
</dl>
<dl>
<dt><code>-dCtransfer='{</code><em>float float ...</em><code>}'</code> or
<dt><code>-dMtransfer=</code>..., <code>-dY</code>..., <code>-dK</code>... or
<dt><code>-dRtransfer='{</code><em>float float ...</em><code>}'</code> or
<dt><code>-dG</code>..., <code>-dB</code>... or
<dt><code>-dKtransfer='{</code><em>float float ...</em><code>}'</code>
<dd>Which you use depends on the algorithm, which may be either either
CMYK, RGB or monochrome. The values are arrays of floats in the range from
0 to 1.0, representing the visible color intensity for the device. One may
achieve similar effects with <code>setcolortransfer</code> at the
language level, but this takes more time and the underlying code for the
driver-specific parameters is still required. The size of the arrays is
arbitrary and the defaults are "<code>{0.0 1.0}</code>", which is a
linear characteristic. Most of the code in <code>stcolor.ps</code> are
better transfer arrays.
</dl>
<dl>
<dt><code>-dKcoding='{</code><em>float...</em><code>}'</code>
<dt><code>-dC</code>..., <code>-dM</code>... etc.
<dd>Arrays between 0.0 and 1.0, controlling the internal coding of the
color values. Clever use of these arrays may yield further enhancements,
but I have no experience yet. (To be discontinued with version 2.x.)
</dl>
<dl>
<dt><code>-sModel=st800</code>
<dd>Causes output to be suitable for the monochrome Stylus 800 (no weaving,
no color).
</dl>
<dl>
<dt><code>-sOutputCode=</code><em>{name}</em>
<dd>Can be either "<code>plain</code>", "<code>runlength</code>" or
"<code>deltarow</code>" and changes the ESC/P2 coding technique
used by the driver. The default is to use runlength encoding.
"<code>plain</code>" selects uncompressed encoding and generates
enormous amounts of data.
</dl>
<dl>
<dt><code>-descp_Band=</code><em>1/8/15/24</em>
<dd>Number of nozzles of scanlines used in printing, Useful only with
<code>-dnoWeave</code>. Larger Values yield smaller code, but this
doesn't increase the printing speed.
</dl>
<dl>
<dt><code>-descp_Width=</code><em>N</em>
<dd>Number of pixels Printed in each scan Line. (Useful only when tuning
margins; see below)
</dl>
<dl>
<dt><code>-descp_Height=</code><em>pixels</em>
<dd>Length of the entire page in pixels. (Parameter of
"<code>ESC(C</code>" in default initialization.)
</dl>
<dl>
<dt><code>-descp_Top=</code><em>scan lines</em>
<dd>Top margin in scan lines. (First parameter of "<code>ESC(c</code>"
in default initialization.)
</dl>
<dl>
<dt><code>-descp_Bottom=</code><em>scan lines</em>
<dd>Bottom margin in scan lines. (Second parameter of
"<code>ESC(c</code>" in default initialization.)
</dl>
<dl>
<dt><code>-sescp_Init=</code>"<em>string</em>"
<dd>Override for the initialization sequence. (Must set graphics mode 1
and units.)
</dl>
<dl>
<dt><code>-sescp_Release=</code>"<em>string</em>"
<dd>Overrides the release sequence, "<code>ESC @ FF</code>" by
default.
</dl>
<p>
ESC/P2 allows any resolutions to be valid in theory, but only
<code>-r360x360</code> (the default) and <code>-r720x720</code> (not
on STC-IIs ? and st800) are known to work with most printers.
<p>
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=7 bgcolor="#CCCC00"><hr><font size="+1">Valid option combinations<br>Stylus I & Pro-Series only</font><hr>
<tr valign=bottom>
<th valign=bottom align=left>Resolution
<td>
<th valign=bottom align=left><code>escp_Band</code>
<td>
<th valign=bottom align=left>Weave usable
<td>
<th valign=bottom align=left><code>escp_Band</code> &<br>number of passes
<tr> <td colspan=7><hr>
<tr valign=top> <td>180x90
<td>
<td>15
<td>
<td><code>noWeave</code>
<td>
<td>
<tr valign=top> <td>180x180
<td>
<td>1 , 8, 24
<td>
<td><code>noWeave</code>, <code>Microweave</code>
<td>
<td>15/2 <code>SoftWeave</code>
<tr valign=top> <td>180x360
<td>
<td>
<td>
<td>
<td>
<td>15/4 <code>SoftWeave</code>
<tr valign=top> <td>180x720
<td>
<td>
<td>
<td>
<td>
<td>15/8 <code>SoftWeave</code>
<tr valign=top> <td>360x90
<td>
<td>15
<td>
<td><code>noWeave</code>
<td>
<td>
<tr valign=top> <td>360x180
<td>
<td>1, 8, 24
<td>
<td><code>noWeave</code>, <code>Microweave</code>
<td>
<td>15/2 <code>SoftWeave</code>
<tr valign=top> <td>360x360
<td>
<td>1, 8, 24
<td>
<td><code>noWeave</code>, <code>Microweave</code>
<td>
<td>15/4 <code>SoftWeave</code>
<tr valign=top> <td>360x720
<td>
<td>
<td>
<td>
<td>
<td>15/8 <code>SoftWeave</code>
<tr valign=top> <td>720x90
<td>
<td>15
<td>
<td><code>noWeave</code>
<td>
<td>
<tr valign=top> <td>720x180
<td>
<td>
<td>
<td>
<td>
<td>15/2 <code>SoftWeave</code>
<tr valign=top> <td>720x360
<td>
<td>
<td>
<td>
<td>
<td>15/4 <code>SoftWeave</code>
<tr valign=top> <td>720x720
<td>
<td>1
<td>
<td><code>noWeave</code>, <code>Microweave</code>
<td>
<td>15/8 <code>SoftWeave</code>
</table></blockquote>
<blockquote>
<b>Beware:</b> there are only few validity checks for parameters. A good
example is <code>escp_Band</code>: if you set this, the driver uses your
value even if the value is not supported by the printer. <b>You asked for
it and you got it!</b>
</blockquote>
<h3><a name="STC_FAQ"></a>Application note and FAQ</h3>
<p>
Quite a bunch of parameters. Hopefully you never need any of them, besides
feeding <code>stcolor.ps</code> to Ghostscript in front of your input.
<p>
After answering some questions over fifty times I prepared a FAQ. Here is
version 1.3 of the FAQ, as of <code>stcolor</code> version 1.20 (for
Ghostscript 3.50).
<h4><a name="STC_FAQ_A3"></a>Support for A3 paper</h4>
<p>
Yes, this driver supports the A3-size printer: merely set the required
pagesize and margins. A simple way to do this is to specify the
command-line switch "<code>-sPAPERSIZE=a3</code>" or include the
procedure call "<code>a3</code>" in the PostScript prolog section. To
optimize the printable area or set the proper margins, see the next
paragraph.
<h4><a name="STC_FAQ_margins"></a>Margins, PageSize</h4>
<p>
I refuse to add code to <code>stcolor</code> that tries to guess the
proper margins or page size, because I found that such guessing is usually
wrong and needs correction in either the source or the parameters. You can
modify <code>stcolor.ps</code> to do that, however. After the line
<blockquote><code>
mark % prepare stack for "putdeviceprops"
</code></blockquote>
<p>
insert these lines, which define page size and margins in points:
<blockquote>
<pre>/.HWMargins [9.0 39.96 12.6 9.0] % Left, bottom, right, top (1/72")
/PageSize [597.6 842.4] % Paper, including margins (1/72")
/Margins [ % neg. Offset to Left/Top in Pixels
4 index 0 get STCold /HWResolution get 0 get mul 72 div neg
5 index 3 get STCold /HWResolution get 1 get mul 72 div neg
]</pre></blockquote>
<p>
Feel free to change the values of <code>.HWMargins</code> and
<code>PageSize</code> to match your needs; the values given are the
defaults when the driver is compiled with "<code>-DA4</code>". This
option or its omission may cause trouble: the Stylus Color can print up to
exactly 8 inches (2880 pixels) at 360dpi. The remaining paper is the
margin, where the left margin varies only slightly with the paper size,
while the right margin is significantly increased for wider paper, such as
U.S. letter size.
<p>
<b>Note</b> that if you are using an ISO paper size with a version of
<code>stcolor</code> after 1.20 and compiled without
"<code>-DA4</code>", then the default margin is too large, and you need
to add the proper "<code>.HWMargins</code>" to the command line or to
<code>stcolor.ps</code>.
<h4><a name="STC_FAQ_II_IIS_1500"></a>Stylus Color II / IIs and 1500</h4>
<p>
First the good news: the driver can print on the Stylus Color II.
Now the bad news:
<ul>
<li>According to Epson support the driver "abuses" the color
capabilities. (See "Future Plans" for details.)
<li>You need some parameters on the command line (or in
<code>stcolor.ps</code>).
<li>I doubted that it would be usable with the Stylus Color IIs, but
it <b>is</b> usable and suffers from mixing problems!
</ul>
<p>
To make things work, you <b>MUST</b> disable the driver's internal
weaving (<code>Softweave</code>), in one of these two ways:
<blockquote>
<code>gs -dMicroweave</code> ...<br>
<code>gs -dnoWeave -descp_Band=1</code> ...
</blockquote>
<p>
Version 1.90, current as of Ghostscript 5.10, fixes this bug by new default
behaviour. I experienced significantly increased printing speed with the
second variant on the old Stylus Color, when printing mostly monochrome
data.
<h3><a name="STC_recommendations"></a>Recommendations</h3>
<p>
The next section is a contribution from Jason Patterson <jason@reflections.com.au>
who evaluated a previous version (1.17). Ghostscript was invoked as follows:
<blockquote><dl compact>
<dt><code>gs</code>
<dd><code>-sDEVICE=stcolor -r720x720
-sDithering=</code>... <code>-sOutputFile=escp.out stcolor.ps
whatsoever.ps</code>
</dl></blockquote>
<p>
where "..." is the name of the desired algorithm.
<code>stcolor.ps</code> was omitted for the gs-algorithms
(<code>gsmono</code>, <code>gsrgb</code> and <code>gscmyk</code>),
for which it is useless and would not allow the selection of
"<code>gscmyk</code>".
<h4><a name="STC_dither_experiment"></a>Color dithering experiments with
<code>gdevstc</code> 1.21</h4>
<p>
Here are data about the EPSON Stylus Color driver's different dithering
methods, based on a little experiment using four good quality scanned
images of quite varied nature, to begin with, a summary of the results of
the four experiments. <b>Sanity note:</b> the results here are from only
four images and a total of 24 printouts (eight on 720dpi paper, sixteen on
plain paper). Your results will almost certainly vary, and your standards
might not be the same as mine, so use these results only as a guide, not as
a formal evaluation.
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=3 bgcolor="#CCCC00"><hr><font size="+1">Quality of output by method</font><hr>
<tr valign=bottom>
<th align=left>
<td>
<th align=left>
<tr> <td colspan=3><hr>
<tr> <td valign=top><code>gsmono</code>
<td>
<td>Pretty much what you'd expect from a mono ordered pattern.
Looks like what a lot of mono laser printers produce.
<tr> <td valign=top><code>fsmono</code>
<td>
<td>Excellent for monochrome.
<tr> <td valign=top><code>gscmyk</code>
<td>
<td>Not very good, but expected from an ordered pattern.
<tr> <td valign=top><code>gsrgb</code>
<td>
<td>A little better than <code>gscmyk</code>. More consistent
looking.
<tr> <td valign=top><code>fs2</code>
<td>
<td>Good, but not quite as good as <code>fsrgb</code>. Gets the
brightness wrong: too light at 720dpi, too dark at 360dpi.
<tr> <td valign=top><code>fsrgb</code>
<td>
<td>Very good, but a little too dark and has a slight blue tint.
<tr> <td valign=top><code>hscmyk</code>
<td>
<td>Excellent. Slightly better than <code>fsrgb</code> and
<code>fs2</code>. Better than <code>fscmyk</code> on
some images, almost the same on most.
<tr> <td valign=top><code>fscmyk</code>
<td>
<td>Best. Very, very slightly better than <code>hscmyk</code>.
On some images nearly as good as the EPSON demos done with
the MS Windows driver.
</table></blockquote>
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=4 bgcolor="#CCCC00"><hr><font size="+1">Overall visual quality (1-10), best to worst</font><hr>
<tr valign=top> <th colspan=4 align=left>Monochrome
<tr> <td>
<td><code>fsmono</code>
<td>
<td><code>******************</code>
<tr> <td>
<td><code>gsmono</code>
<td>
<td><code>**********</code>
<tr> <td>
<td>
<td>
<td><code>0 1 2 3 4 5 6 7 8 9 10</code>
<tr> <td colspan=4><hr>
<tr valign=top> <th colspan=4 align=left>Colour
<tr> <td>
<td><code>fscmyk</code>
<td>
<td><code>*******************</code>
<tr> <td>
<td><code>hscmyk</code>
<td>
<td><code>*******************</code>
<tr> <td>
<td><code>fsrgb</code>
<td>
<td><code>******************</code>
<tr> <td>
<td><code>fs2</code>
<td>
<td><code>*****************</code>
<tr> <td>
<td><code>gsrgb</code>
<td>
<td><code>**********</code>
<tr> <td>
<td><code>gscmyk</code>
<td>
<td><code>*********</code>
<tr> <td>
<td>
<td>
<td><code>0 1 2 3 4 5 6 7 8 9 10</code>
</table></blockquote>
<h3><a name="STC_color_transform"></a>Color transformation</h3>
<p>
In the initial version of the driver distributed with Ghostscript 3.33, the
parameter "<code>SpotSize</code>" was the only way to manipulate the
colors at the driver level. According to the parameters enumerated above,
this has changed significantly with version 1.16 and above as a result an
ongoing discussion about dithering algorithms and "false color" on the
Epson Stylus Color. This initiated the transformation of the
<code>stcolor</code> driver into a framework for different dithering
algorithms, providing a generalized interface to the internal Ghostscript
color models and the other data structures related to Ghostscript drivers.
<p>
The main thing such a framework should be able to do is to deliver the
values the dithering algorithm needs; and since this directly influences
the optical image impression, this transformation should be adjustable
without the need for recompilation and relinking. In general the process
can be described as follows:
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td colspan=3><code>ColorAdjustMatrix</code>
<td align=center>Coding
<td colspan=3>
<td align=center>Transfer
<td colspan=3>
<tr valign=top> <td>|
<td align=center>Ghostscript color
<td>|
<td align=center>=>
<td>|
<td align=center>Ghostscript raster
<td>|
<td align=center>=>
<td>|
<td align=center>Dithering data
<td>|
<tr valign=top> <td>|
<td>
<td>|
<td>
<td>|
<td align=center>1/2/4/8/16/32-bit
<td>|
<td>
<td>|
<td>
<td>|
<tr valign=top> <td>|
<td align=center>1/3/4 16-bit values
<td>|
<td>
<td>|
<td align=center>1/3/4 values
<td>|
<td>
<td>|
<td align=center>(arbitrary type)
<td>|
</table></blockquote>
<p>
Due to the limitations on raster storage, information is lost in the first
transformation step, except for the 16-bit monochrome mode. So any color
adjustment should take place before this step and this is where the optional
<code>ColorAdjustMatrix</code> works.
<p>
The first transformation step, called "coding", is controlled by the
<code>?coding</code> arrays. The decoding process expands the range of
values expontentially to a larger range than that provided by the initial
Ghostscript color model, and is therefore a reasonable place to make
device- or algorithm-specific adjustments. This is where the
<code>?transfer</code> arrays are used. Array access might be not the
fastest method, but its generality is superior, so this step is always
based upon internally algorithm-specific array access. If 8 bits are stored
per color component and if the algorithm uses bytes too, the second
transformation is included within the first, which saves significant
computation time when printing the data.
<h3><a name="STC_CAM"></a><code>ColorAdjustMatrix</code></h3>
<p>
The driver supports different values for <code>ProcessColorModel</code>,
which raises the need for different color adjustments. Here
"<code>CAM</code>" stands for "<code>ColorAdjustMatrix</code>".
<dl>
<dt><code>DeviceGray</code> (three floats)
<dd><pre>if ((r == g) && (g == b))
K' = 1.0 - R;
else
K' = 1.0 - CAM[0] * R + CAM[1] * G + CAM[2] * B;</pre>
<p>
According to the <a href="Drivers.htm">documentation on drivers</a>, the
latter (the "else" clause) should never happen.
</dl>
<dl>
<dt><code>DeviceRGB</code> (nine floats)
<dd><pre>if((r == g) && (g == b))
R' = B' = G' = R;
else
R' = CAM[0]*R + CAM[1]*G + CAM[2]*B;
G' = CAM[3]*R + CAM[4]*G + CAM[5]*B;
B' = CAM[6]*R + CAM[7]*G + CAM[8]*B;</pre>
<p>
The printer always uses four inks, so a special treatment of black is
provided. Algorithms may take special action if R, G, and B are all
equal.
</dl>
<dl>
<dt><code>DeviceCMYK</code> (sixteen floats)
<dd>
<pre>if((c == m) && (m == y))
K' = max(C,K);
C' = M' = Y' = 0;
else
K = min(C,M,Y);
if((K > 0) && ColorAdjustMatrix_present) { => UCR
C -= K;
M -= K;
Y -= K;
}
C' = CAM[ 0]*C + CAM[ 1]*M + CAM[ 2]*Y + CAM[ 3]*K;
M' = CAM[ 4]*C + CAM[ 5]*M + CAM[ 6]*Y + CAM[ 7]*K;
Y' = CAM[ 8]*C + CAM[ 9]*M + CAM[10]*Y + CAM[11]*K;
K' = CAM[12]*C + CAM[13]*M + CAM[14]*Y + CAM[15]*K;</pre>
<p>
Again we have a special black treatment. "<code>max(C,K)</code>" was introduced
because of a slight misbehaviour of Ghostscript, which delivers
black under certain circumstances as (1,1,1,0). Normally, when
no special black separation and undercolor removal procedures
are defined at the PostScript level, either (C,M,Y,0) or (0,0,0,K)
values are mapped. This would make the extended <code>ColorAdjustMatrix</code>
quite tedious, and so during mapping, black separation is done for
(C,M,Y,0) requests; and if there is a <code>ColorAdjustMatrix</code>, undercolor
removal is used too. In other words the default matrix is:
<blockquote><table>
<tr> <td>1 <td>0 <td>0 <td>1
<tr> <td>0 <td>1 <td>0 <td>1
<tr> <td>0 <td>0 <td>1 <td>1
<tr> <td>0 <td>0 <td>0 <td>1
</table></blockquote>
<p>
and it is applied to CMYK values with separated and removed black. Raising
the CMY coefficients while lowering the K coefficients reduces black and
intensifies color. But be careful, because even small deviations from the
default cause drastic changes.
</dl>
<p>
If no <code>ColorAdjustMatrix</code> is set, the matrix computations are
skipped. Thus the transformation reduces to range inversion in monochrome
mode and black separation in CMYK mode.
<h3><a name="STC_RGBCMYK_coding"></a>RGB / CMYK coding and transfer, and <code>BitsPerPixel</code></h3>
<p>
These two (groups of) parameters are arrays of floating-point numbers in
the range 0.0 to 1.0. They control the truncation to the desired number of
bits stored in raster memory (<code>BitsPerPixel</code>) and the ink
density. The "truncation" may become a nonlinear function if any of the
<code>?coding</code> arrays is set. Assume the following Ghostscript
invocation:
<blockquote><pre>gs -sDEVICE=stcolor -sDithering=fscmyk -dBitsPerPixel=16 \
-dKcoding='{ 0.0 0.09 0.9 1.0 }' \
-dMcoding='{ 0.0 0.09 0.9 1.0 }' \
-dKtransfer='{ 0.0 0.09 0.9 1.0 }' \
-dYtransfer='{ 0.0 0.09 0.9 1.0 }'</pre>
</blockquote>
<p>
We may have either or both of <code>?coding</code> and
<code>?transfer</code>, giving four possible combinations. (These four
combinations appear in the given example.) The resulting mapping appears
in the following tables, where except for the internal Indices (4
components × 4 bits = 16 <code>BitsPerPixel</code>), all values
are normalized to the range 0 to 1. The actual range is 0 to 65535 for the
Ghostscript color and 0 to 16777215 for the ink values delivered to the
<code>fscmyk</code> algorithm. Sorry for the bunch of numbers
following, but you may try this example in conjunction with
<code>stcinfo.ps</code>, which should give you a graphical printout of
the following numbers when you issue a <code>showpage</code> command.
<blockquote><table cellpadding=0 cellspacing=0>
<tr> <td>
<td>
<th colspan=5>Cyan<hr>
<td>
<th colspan=5>Magenta<hr>
<tr valign=top> <th>CI/15
<td>
<th>gs_color_values
<td>
<th>CI
<td>
<th>Ink
<td>
<th>gs_color_values
<td>
<th>CI
<td>
<th>Ink
<tr> <td colspan=13><hr>
<tr valign=top> <td align=center>0.000
<td>
<td align=center>0.000 - 0.062
<td>
<td align=right>0
<td>
<td align=center>0.000
<td>
<td align=center>-0.123 - 0.123
<td>
<td align=right>0
<td>
<td align=center>0.000
<tr valign=top> <td align=center>0.067
<td>
<td align=center>0.063 - 0.125
<td>
<td align=right>1
<td>
<td align=center>0.067
<td>
<td align=center>0.123 - 0.299
<td>
<td align=right>1
<td>
<td align=center>0.247
<tr valign=top> <td align=center>0.133
<td>
<td align=center>0.125 - 0.187
<td>
<td align=right>2
<td>
<td align=center>0.133
<td>
<td align=center>0.299 - 0.365
<td>
<td align=right>2
<td>
<td align=center>0.351
<tr valign=top> <td align=center>0.200
<td>
<td align=center>0.188 - 0.250
<td>
<td align=right>3
<td>
<td align=center>0.200
<td>
<td align=center>0.365 - 0.392
<td>
<td align=right>3
<td>
<td align=center>0.379
<tr valign=top> <td align=center>0.267
<td>
<td align=center>0.250 - 0.312
<td>
<td align=right>4
<td>
<td align=center>0.267
<td>
<td align=center>0.392 - 0.420
<td>
<td align=right>4
<td>
<td align=center>0.406
<tr valign=top> <td align=center>0.333
<td>
<td align=center>0.313 - 0.375
<td>
<td align=right>5
<td>
<td align=center>0.333
<td>
<td align=center>0.420 - 0.447
<td>
<td align=right>5
<td>
<td align=center>0.433
<tr valign=top> <td align=center>0.400
<td>
<td align=center>0.375 - 0.437
<td>
<td align=right>6
<td>
<td align=center>0.400
<td>
<td align=center>0.447 - 0.475
<td>
<td align=right>6
<td>
<td align=center>0.461
<tr valign=top> <td align=center>0.467
<td>
<td align=center>0.438 - 0.500
<td>
<td align=right>7
<td>
<td align=center>0.467
<td>
<td align=center>0.475 - 0.502
<td>
<td align=right>7
<td>
<td align=center>0.488
<tr valign=top> <td align=center>0.533
<td>
<td align=center>0.500 - 0.562
<td>
<td align=right>8
<td>
<td align=center>0.533
<td>
<td align=center>0.502 - 0.529
<td>
<td align=right>8
<td>
<td align=center>0.516
<tr valign=top> <td align=center>0.600
<td>
<td align=center>0.563 - 0.625
<td>
<td align=right>9
<td>
<td align=center>0.600
<td>
<td align=center>0.529 - 0.557
<td>
<td align=right>9
<td>
<td align=center>0.543
<tr valign=top> <td align=center>0.667
<td>
<td align=center>0.625 - 0.687
<td>
<td align=right>10
<td>
<td align=center>0.667
<td>
<td align=center>0.557 - 0.584
<td>
<td align=right>10
<td>
<td align=center>0.571
<tr valign=top> <td align=center>0.733
<td>
<td align=center>0.688 - 0.750
<td>
<td align=right>11
<td>
<td align=center>0.733
<td>
<td align=center>0.584 - 0.612
<td>
<td align=right>11
<td>
<td align=center>0.598
<tr valign=top> <td align=center>0.800
<td>
<td align=center>0.750 - 0.812
<td>
<td align=right>12
<td>
<td align=center>0.800
<td>
<td align=center>0.612 - 0.639
<td>
<td align=right>12
<td>
<td align=center>0.626
<tr valign=top> <td align=center>0.867
<td>
<td align=center>0.813 - 0.875
<td>
<td align=right>13
<td>
<td align=center>0.867
<td>
<td align=center>0.639 - 0.715
<td>
<td align=right>13
<td>
<td align=center>0.653
<tr valign=top> <td align=center>0.933
<td>
<td align=center>0.875 - 0.937
<td>
<td align=right>14
<td>
<td align=center>0.933
<td>
<td align=center>0.715 - 0.889
<td>
<td align=right>14
<td>
<td align=center>0.778
<tr valign=top> <td align=center>1.000
<td>
<td align=center>0.938 - 1.000
<td>
<td align=right>15
<td>
<td align=center>1.000
<td>
<td align=center>0.889 - 1.111
<td>
<td align=right>15
<td>
<td align=center>1.000
</table></blockquote>
<p>
The difference between cyan and magenta is the presence of a coding array.
The coding process must map a range of color values to each of the sixteen
component indices. If no coding array is given, this is accomplished
by dividing by 4096, equivalent to a right shift by 12 bits. The
final ink density resides in the given interval and moves from the left to
the right side from 0 to 15. For magenta there is a coding array
and the ink value matches the center of the intervals. But the distribution
of the mapped intervals follows the given coding array and is nonlinear in
the linear color space of Ghostscript.
<p>
Now let us take a look at the case with transfer arrays:
<blockquote><table cellpadding=0 cellspacing=0>
<tr> <td>
<td>
<th colspan=5>Yellow<hr>
<td>
<th colspan=5>Black<hr>
<tr valign=top> <th>CI/15
<td>
<th>gs_color_values
<td>
<th>CI
<td>
<th>Ink
<td>
<th>gs_color_values
<td>
<th>CI
<td>
<th>Ink
<tr> <td colspan=13><hr>
<tr valign=top> <td align=center>0.000
<td>
<td align=center>0.000 - 0.062
<td>
<td align=right>0
<td>
<td align=center>0.000
<td>
<td align=center>-0.123 - 0.123
<td>
<td align=right>0
<td>
<td align=center>0.000
<tr valign=top> <td align=center>0.067
<td>
<td align=center>0.063 - 0.125
<td>
<td align=right>1
<td>
<td align=center>0.018
<td>
<td align=center>0.123 - 0.299
<td>
<td align=right>1
<td>
<td align=center>0.067
<tr valign=top> <td align=center>0.133
<td>
<td align=center>0.125 - 0.187
<td>
<td align=right>2
<td>
<td align=center>0.036
<td>
<td align=center>0.299 - 0.365
<td>
<td align=right>2
<td>
<td align=center>0.133
<tr valign=top> <td align=center>0.200
<td>
<td align=center>0.188 - 0.250
<td>
<td align=right>3
<td>
<td align=center>0.054
<td>
<td align=center>0.365 - 0.392
<td>
<td align=right>3
<td>
<td align=center>0.200
<tr valign=top> <td align=center>0.267
<td>
<td align=center>0.250 - 0.312
<td>
<td align=right>4
<td>
<td align=center>0.072
<td>
<td align=center>0.392 - 0.420
<td>
<td align=right>4
<td>
<td align=center>0.267
<tr valign=top> <td align=center>0.333
<td>
<td align=center>0.313 - 0.375
<td>
<td align=right>5
<td>
<td align=center>0.090
<td>
<td align=center>0.420 - 0.447
<td>
<td align=right>5
<td>
<td align=center>0.333
<tr valign=top> <td align=center>0.400
<td>
<td align=center>0.375 - 0.437
<td>
<td align=right>6
<td>
<td align=center>0.252
<td>
<td align=center>0.447 - 0.475
<td>
<td align=right>6
<td>
<td align=center>0.400
<tr valign=top> <td align=center>0.467
<td>
<td align=center>0.438 - 0.500
<td>
<td align=right>7
<td>
<td align=center>0.414
<td>
<td align=center>0.475 - 0.502
<td>
<td align=right>7
<td>
<td align=center>0.467
<tr valign=top> <td align=center>0.533
<td>
<td align=center>0.500 - 0.562
<td>
<td align=right>8
<td>
<td align=center>0.576
<td>
<td align=center>0.502 - 0.529
<td>
<td align=right>8
<td>
<td align=center>0.533
<tr valign=top> <td align=center>0.600
<td>
<td align=center>0.563 - 0.625
<td>
<td align=right>9
<td>
<td align=center>0.738
<td>
<td align=center>0.529 - 0.557
<td>
<td align=right>9
<td>
<td align=center>0.600
<tr valign=top> <td align=center>0.667
<td>
<td align=center>0.625 - 0.687
<td>
<td align=right>10
<td>
<td align=center>0.900
<td>
<td align=center>0.557 - 0.584
<td>
<td align=right>10
<td>
<td align=center>0.667
<tr valign=top> <td align=center>0.733
<td>
<td align=center>0.688 - 0.750
<td>
<td align=right>11
<td>
<td align=center>0.920
<td>
<td align=center>0.584 - 0.612
<td>
<td align=right>11
<td>
<td align=center>0.733
<tr valign=top> <td align=center>0.800
<td>
<td align=center>0.750 - 0.812
<td>
<td align=right>12
<td>
<td align=center>0.940
<td>
<td align=center>0.612 - 0.639
<td>
<td align=right>12
<td>
<td align=center>0.800
<tr valign=top> <td align=center>0.867
<td>
<td align=center>0.813 - 0.875
<td>
<td align=right>13
<td>
<td align=center>0.960
<td>
<td align=center>0.639 - 0.715
<td>
<td align=right>13
<td>
<td align=center>0.867
<tr valign=top> <td align=center>0.933
<td>
<td align=center>0.875 - 0.937
<td>
<td align=right>14
<td>
<td align=center>0.980
<td>
<td align=center>0.715 - 0.889
<td>
<td align=right>14
<td>
<td align=center>0.933
<tr valign=top> <td align=center>1.000
<td>
<td align=center>0.938 - 1.000
<td>
<td align=right>15
<td>
<td align=center>1.000
<td>
<td align=center>0.889 - 1.111
<td>
<td align=right>15
<td>
<td align=center>1.000
</table></blockquote>
<p>
Yellow uses a transfer array. There is no linear correspondence between
the color and the ink values: this correspondence is defined through the
given array. In other words, the transfer arrays define a nonlinear ink
characteristic, which is exactly the same functionality that PostScript's
"(color)transfer" function provides.
<p>
While for yellow the intervals match the intervals used with cyan, for
black the intervals match the magenta intervals. But watch the
correspondence between the CI/15 values and the ink density for black: this
is a linear distribution in the ink domain.
<p>
Not a bad idea, I think. Consider the <code>fs2</code> algorithm: it
uses values in the range 0 to 255. If any transfer array were alone, some
of the 256 possible values would never be used and others would be used for
adjacent intervals several times. Establishing an identical coding array
solves this problem, so the full potential of the algorithm is used.
<p>
Another useful feature of the coding arrays is that they are internally
normalized to the range 0-1. In 720x720dpi mode the transfer arrays in
<code>stcolor.ps</code> limit the dot density to about 50%, so these
arrays end at 0.5 (and begin at 0.5 for RGB). Because of automatic
normalization, these arrays can also be used as coding arrays. But of
course in the <code>fs2</code> case mentioned above, values from 0 to
127 will never be delivered to the algorithm, while values 128-255 are
delivered for adjacent intervals.
<p>
To clarify the intended use of the three parameters (parameter groups), keep this in mind:
<blockquote><ul>
<li><code>ColorAdjustMatrix</code> is never used when transferring gray
values. This restricts it to what the name says: adjustment of colors,
that is, correction for miscolored ink. Do not use it for saturation or
brightness control.
<li><code>?transfer</code> arrays control the values delivered to the
driver, which in turn controls the ink quantity. Use these arrays to
control saturation and brightness. In general these arrays are identical
for all inks. If they differ they provide a simpler scheme for color
correction, which is not necessarily faster than the
<code>ColorAdjustMatrix</code>.
<li><code>?coding</code> arrays control the color value intervals mapped
to the internal color indices.
</ul></blockquote>
<h3><a name="What_is_weaving"></a>What is weaving?</h3>
<p>
The Epson Stylus Color has a head assembly that contains two physically
identifiable heads, one for black and one for cyan, magenta, and yellow
(CMY). This makes four "logical" heads, one for each color component.
Each of these four heads has several jets at some vertical (Y) distance
from one another, so several horizontal lines can be printed of a given
color during one pass of the heads. From experience I think there are
fifteen jets per color, spaced at 1/90in.
<p>
So the question arises of how to print at a Y resolution of 360dpi with
90dpi jets. Simply by division one gets 360dpi/90dpi = 4, which tells us
that 4 passes of the head assembly are needed to achieve a Y resolution of
360dpi.
<p>
Weaving is the method of how the fifteen jets are used to print adjacent
horizontal rows separated here by 1/360 inch:
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=17 bgcolor="#CCCC00"><hr><font size="+1">Print-head jets used with and without weaving</font><hr>
<tr> <td>
<td>
<th valign=bottom colspan=7>Weaving<hr>
<td>
<th valign=bottom colspan=7>noWeave<hr>
<tr valign=top> <td>
<th>Pass
<th>1
<td>
<th>2
<td>
<th>3
<td>
<th>4
<td>
<th>1
<td>
<th>2
<td>
<th>3
<td>
<th>4
<tr> <th>Row
<tr valign=top> <td align=center>0
<td>
<td align=center>jet 0
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 0
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<tr valign=top> <td align=center>1
<td>
<td align=center>--
<td>
<td align=center>jet 1
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 0
<td>
<td align=center>--
<td>
<td align=center>--
<tr valign=top> <td align=center>2
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 2
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 0
<td>
<td align=center>--
<tr valign=top> <td align=center>3
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 3
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 0
<tr valign=top> <td align=center>4
<td>
<td align=center>jet 1
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 1
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<tr valign=top> <td align=center>5
<td>
<td align=center>--
<td>
<td align=center>jet 2
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 1
<td>
<td align=center>--
<td>
<td align=center>--
<tr valign=top> <td align=center>6
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 3
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>--
<td>
<td align=center>jet 1
<td>
<td align=center>--
<tr valign=top> <th>...
</table></blockquote>
<p>
Now let's assume that the dot diameter is different for each individual
jet, but the average among the jets matches the desired resolution. With
weaving, adjacent rows are printed by different jets, thus some averaging
takes place. Without weaving, adjacent rows are printed by the same jet
and this makes the dot diameter deviations visible as 1/90in stripes on
the paper.
<h3><a name="STC_print_modes"></a>Print mode parameters</h3>
<p>
The parameters "<code>Unidirectional</code>",
"<code>Microweave</code>", "<code>noWeave</code>",
"<code>OutputCode</code>", "<code>Model</code>" and the given
resolution control the data generated for the printer.
<h4><a name="STC_unidirectional"></a><code>Unidirectional</code></h4>
<p>
Simply toggles the unidirectional mode of the printer. Setting
"<code>Unidirectional</code>" definitely slows printing speed, but may
improve the quality. I use this for printing transparencies, where fast
head movement could smear the ink.
<h4><a name="STC_noweave"></a><code>Microweave</code>,
<code>noWeave</code> and <code>OutputCode=deltarow</code></h4>
<p>
The first are two booleans, which implies that four combinations are
possible. Actually only three exist (if you don't count for
<code>deltarow</code>): <code>Softweave</code>,
<code>Microweave</code>, and <code>noWeave</code>. The first and
second are functionally identical, the difference being whether the driver
or the printer does the job.
<p>
In the default <code>Softweave</code> mode the driver sends the data
properly arranged to the printer, while in <code>Microweave</code> mode,
it is the printer that arranges the data. But in general the host processor
is much faster than the printer's processor, and thus it is faster for the
host do the job. In addition to that, for 720dpi eight passes are
required, and the amount of buffer space needed to buffer the data for the
passes is far beyond the printer's memory. <code>Softweave</code>
requires an odd value of "<code>escp_Band</code>"; the Stylus Color
provides fifteen for that.
<p>
"<code>OutputCode</code>" controls the encoding used. In the basic
modes, the choice consists of "plain" and "runlength". The computation of
runlength-encoded data does not take much time, less than the data tranfer
to the printer; thus this is the recommended mode, and of course the
default. With the Stylus Color, Epson introduced some new encoding
principles, namely "tiff" and "deltarow". While the first was omitted from
this driver for lack of apparent advantages, "<code>deltarow</code>" is
available as an option. "<code>Softweave</code>" cannot be used with
this encoding, so if <code>OutputCode=deltarow</code> is set,
<code>Microweave</code> becomes the default. Maybe that the size of the
ESC/P2 code becomes smaller, but I have never observed faster printing
speed. Things tend to become slower with <code>deltarow</code> compared
to <code>Softweave</code>.
<h4><a name="STC_model"></a><code>Model</code></h4>
<p>
Some ESC/P2 printers such as the Stylus 800 do not offer
<code>Microweave</code> or the commands required to do
<code>Softweave</code>. Setting <code>Model</code> just changes the
defaults and omits some parts of the initialization sequence which are not
compatible with the given printer model. Currently only
"<code>st800</code>" is supported besides the default
<code>stcolor</code>.
<h3><a name="STC_Pitfalls"></a>Bugs and pitfalls</h3>
<ul>
<li>The given <code>?coding</code> and <code>?transfer</code> arrays
should be strictly monotonic.
<li>It is impossible to change <code>WHITE</code>: that's your paper.
Thus RGB transfer should end at 1.0 and CMYK transfer should start at 0.0.
<li>Usually 8 bits per component yields fastest operation.
<li>The <code>ColorAdjustMatrix</code> is not used in the reverse
transformation used when Ghostscript does the dithering
(<code>gs</code>* modes). Expect funny results.
<li>If <code>BitsPerPixel</code> is less than 6, the entire coding and
transfer process does not work. This is always true for the
<code>gs</code>* modes and becomes true for the other modes if
<code>BitsPerPixel</code> is forced to low values.
<li>720×720dpi printing should never select the <code>gs</code>*
modes and should always use <code>stcolor.ps</code>. (I prefer
360×720.)
</ul>
<h3><a name="STC_Tests"></a>Tests</h3>
<p>
This section gives an overview of performance in terms of processing and
printing times, from tests run after version 1.13. Printing was done
offline (simply copying a processed file to the printer) to measure real
printing speed without regard to speed of processing on the host, since at
high resolutions, processing time is the same order of magnitude and thus
may become the limiting factor.
<h4><a name="STC_OutputCodes"></a>The various OutputCodes</h4>
<p>
I ran several files though Ghostscript and recorded the size of the
resulting print code, the processing time, and the printing time, at least
for some of the files, always using these options:
<blockquote><code>
gs -sDEVICE=stcolor -sPAPERSIZE=a4 stcolor.ps - < file.ps
</code></blockquote>
<p>
(Actually "<code>-sPAPERSIZE=a4</code>" is in my
<code>gs_init.ps</code> since I'm a germ.)
<p>"<code>deltarow</code>" is the new encoding principle
("<code>ESC . 3 10 10 1</code>") with
<code>Microweave</code> on. It is activated with
"<code>-sOutputCode=deltarow</code>".
<p>"<code>Softweave</code>" actually means that nothing else was used:
it is the default, and implies that odd v=40/h=10/m=15 mode
("<code>ESC . 1 40 10 15</code>").
<p>"<code>Microweave</code>" means "<code>-dMicroweave</code>",
equivalent to "<code>ESC . 1 10 10 1</code>",
with full skip optimization and microweave activated.
<p>
Finally I wanted to see the plain Kathy Ireland, and used
"<code>-sOutputCode=plain</code>", which just replaces runlength
encoding (RLE) by no encoding, thus using
"<code>ESC . 0 40 10 15</code>". [So sorry
<code>;-)</code> Kathy was still dressed in blue in front of the blue
sea on a blue air cushion -- nice to see but hard to dither.]
<p>
So here are the results.
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=9 bgcolor="#CCCC00"><hr><font size="+1">File sizes and printing speeds with various weaving methods</font><hr>
<tr valign=bottom>
<td>
<td>
<th><code>golfer.ps</code>
<td>
<th><code>colorcir.ps</code>
<td>
<th><code>drawing.ps</code>
<td>
<th><code>brief.ps</code>
<tr> <td colspan=9><hr>
<tr valign=top> <td><code>deltarow</code>
<td>
<td>572751/48.180u
<td>
<td>643374/41.690u
<td>
<td>90142/46.180u/1:50
<td>
<td>178563/49.350u/2:22
<tr valign=top> <td><code>Softweave</code>
<td>
<td>559593/46.810u
<td>
<td>669966/44.960u
<td>
<td>296168/48.160u/1:30
<td>
<td>269808/43.320u/1:55
<tr valign=top> <td><code>Microweave</code>
<td>
<td>590999/56.060u
<td>
<td>754276/42.890u
<td>
<td>338885/47.060u/1:50
<td>
<td>282314/44.690u/2:22
</table></blockquote>
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=3 bgcolor="#CCCC00"><hr><font size="+1">Kathy Ireland</font><hr>
<tr valign=bottom>
<td>
<td>
<th><code>kathy.ps</code>
<tr> <td colspan=3><hr>
<tr valign=top> <td><code>deltarow</code>
<td>
<td>3975334/111.940u/5:35
<tr valign=top> <td><code>Softweave</code>
<td>
<td>3897112/101.940u/3:10
<tr valign=top> <td><code>Microweave</code>
<td>
<td>4062829/100.990u/3:15
<tr valign=top> <td><code>plain/soft</code>
<td>
<td>5072255/104.390u/3:05
</table></blockquote>
<p>
It may be that I've not chosen the optimal <code>deltarow</code> code,
but even if it saves at lot of bytes, printing-speed is not increased.
<p>
At least the printer prefers plain Kathy. In other words, sending 1
Megabyte or 20% more data has no impact on printing speed.
<code>drawing.ps</code> is an exception to this rule: plain prints
slower than RLE.
<p>
"Unclever" coding -- especially with <code>deltarow</code> -- can
significantly slow down printing. But even if very significant advantages
in the size of the code are achieved, "<code>deltarow</code>" is not
competitive. <code>colorcir.ps</code> shows savings with
<code>deltarow</code>, but printing is a mess.
<h4><a name="STC_printing_time"></a>Printing time related to other options</h4>
<p>
Full page halftone images printed, unless otherwise noted.
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=11 bgcolor="#CCCC00"><hr><font size="+1">Printing time related to other options</font><hr>
<tr valign=top> <th>dpi
<td>
<th colspan=3>Print mode
<td>
<th>Size KB
<td>
<th>Time
<td>
<th align=left>Comments
<tr> <td colspan=11><hr>
<tr valign=top> <td>180x180
<td>
<td>mono
<td>
<td align=right>-/uni
<td>
<td align=right>358
<td>
<td align=right>1:15
<td>
<td>
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>-/bi
<td>
<td align=right>358
<td>
<td align=right>0:45
<td>
<td>
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>micro/bi
<td>
<td align=right>205
<td>
<td align=right>0:45
<td>
<td>Not weaving
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>179
<td>
<td align=right>1:25
<td>
<td>
<tr valign=top> <td>
<td>
<td>color
<td>
<td align=right>-/bi
<td>
<td align=right>641
<td>
<td align=right>2:45
<td>
<td>
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>556
<td>
<td align=right>1:32
<td>
<td>
<tr valign=top> <td>360x360
<td>
<td>mono
<td>
<td align=right>-/uni
<td>
<td align=right>269
<td>
<td align=right>0:50
<td>
<td>Monochrome text
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>-/bi
<td>
<td align=right>269
<td>
<td align=right>0:35
<td>
<td>Monochrome text
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>micro/bi
<td>
<td align=right>269
<td>
<td align=right>2:25
<td>
<td>Monochrome text
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/uni
<td>
<td align=right>250
<td>
<td align=right>3:15
<td>
<td>Monochrome text
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>250
<td>
<td align=right>1:55
<td>
<td>Monochrome text
<tr valign=top> <td>
<td>
<td>color
<td>
<td align=right>-/bi
<td>
<td align=right>346
<td>
<td align=right>1:00
<td>
<td>Sparse-color page, visible displacements
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>micro/bi
<td>
<td align=right>346
<td>
<td align=right>1:50
<td>
<td>Sparse-color page, looks buggy -- printer?
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>294
<td>
<td align=right>1:30
<td>
<td>Sparse-color page, O.K.
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>-/bi
<td>
<td align=right>2218
<td>
<td align=right>2:45
<td>
<td>Visible stripes
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>micro/bi
<td>
<td align=right>5171
<td>
<td align=right>3:17
<td>
<td>
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>3675
<td>
<td align=right>3:05
<td>
<td>
<tr valign=top> <td>360x720
<td>
<td>mono
<td>
<td align=right>soft/bi
<td>
<td align=right>2761
<td>
<td align=right>5:40
<td>
<td>
<tr valign=top> <td>
<td>
<td>color
<td>
<td align=right>soft/bi
<td>
<td align=right>7789
<td>
<td align=right>6:15
<td>
<td>Just a small difference!
<tr valign=top> <td>720x360
<td>
<td>color
<td>
<td align=right>soft/bi
<td>
<td align=right>7182
<td>
<td align=right>5:40
<td>
<td>
<tr valign=top> <td>720x720
<td>
<td>color
<td>
<td align=right>micro/bi
<td>
<td align=right>14748
<td>
<td align=right>30:26
<td>
<td>Actually beyond printer's capabilities
<tr valign=top> <td>
<td>
<td align=right>
<td>
<td align=right>soft/bi
<td>
<td align=right>14407
<td>
<td align=right>11:08
<td>
<td>
</table></blockquote>
<h3><a name="STC_acks"></a>Acknowledgments</h3>
<p>
This driver was copied from <code>gdevcdj.c</code> (Ghostscript 3.12),
which was contributed by George Cameron, Koert Zeilstra, and Eckhard
Rueggeberg. Some of the ESC/P2 code was drawn from Richard Brown's
<code>gdevescp.c</code>. The POSIX interrupt code (compilation option
<code>-DSTC_SIGNAL</code>) is from Frederic Loyer. Several improvements
are based on discussions with Brian Converse, Bill Davidson, Gero Guenther,
Jason Patterson, ? Rueschstroer, and Steven Singer.
<p>
While I wish to thank everyone mentioned above, they are by no means
responsible for bugs in the stcolor driver -- just for the features.
<address>
Gunther Hess<br>
Richard Wagner Strasse 112<br>
D-47057 Duisburg<br>
Germany<br>
+49 203 376273 telephone (MET evening hours)<br>
<<a href="mailto:ghess@elmos.de">ghess@elmos.de</a>>
</address>
<hr>
<h2><a name="Uniprint"></a>uniprint, a flexible unified printer driver</h2>
<p>
<code>uniprint</code> is a unified parametric driver by Gunther Hess
<<a href="mailto:ghess@elmos.de">ghess@elmos.de</a>> for several
kinds of printers and devices, including
<blockquote>
<ul>
<li>any Epson Stylus Color, Stylus, or Stylus Pro
<li>HP PCL/RTL
<li>Canon BubbleJet Color 610
<li>NEC P2X
<li>Sun raster file format
</ul></blockquote>
<p>
This driver is intended to <em>become</em> a unified printer driver. If you
consider it ugly, please send me your suggestions for improvements. The
driver will be updated with them. Thus the full explanation of the driver's
name is:
<blockquote>
Ugly- -> Updated- -> Unified Printer Driver
</blockquote>
<p>
But you probably want to know something about the functionality.
At the time of this writing uniprint drives:
<ul>
<li>NEC Pinwriter P2X (24-pin monochrome impact printer, ESC/P style)
<li>Several Epson Stylus Color models (ESC/P2 style)
<li>HP-DeskJet 550c (basic HP-RTL)
<li>Canon BJC 610
</ul>
<p>
It can be configured for various other printers without recompilation
and offers uncompressed (ugly) Sun rasterfiles as another format, but
this format is intended for testing purposes rather than real use.
The usage of this driver is quite simple. The typical command line looks
like this:
<blockquote>
<code>gs @</code>{MODEL}<code>.upp -sOutputFile=</code>{printable file}<code> MyFile.ps -c quit</code>
</blockquote>
<p>
For example, from my Linux box:
<blockquote><code>
gs @stc.upp -sOutputFile=/dev/lp1 tiger.eps -c quit
</code></blockquote>
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=6 bgcolor="#CCCC00"><hr><font size="+1">Unified Printer Parameter files distributed with Ghostscript</font><hr>
<tr> <th align=left colspan=6>Canon BJC 610 (color, rendered)
<tr valign=top> <td>
<td><code>bjc610a0.upp</code>
<td>
<td>360×360dpi
<td>
<td>plain paper, high speed
<tr valign=top> <td>
<td><code>bjc610a1.upp</code>
<td>
<td>360×360dpi
<td>
<td>plain paper
<tr valign=top> <td>
<td><code>bjc610a2.upp</code>
<td>
<td>360×360dpi
<td>
<td>coated paper
<tr valign=top> <td>
<td><code>bjc610a3.upp</code>
<td>
<td>360×360dpi
<td>
<td>transparency film
<tr valign=top> <td>
<td><code>bjc610a4.upp</code>
<td>
<td>360×360dpi
<td>
<td>back print film
<tr valign=top> <td>
<td><code>bjc610a5.upp</code>
<td>
<td>360×360dpi
<td>
<td>fabric sheet
<tr valign=top> <td>
<td><code>bjc610a6.upp</code>
<td>
<td>360×360dpi
<td>
<td>glossy paper
<tr valign=top> <td>
<td><code>bjc610a7.upp</code>
<td>
<td>360×360dpi
<td>
<td>high gloss film
<tr valign=top> <td>
<td><code>bjc610a8.upp</code>
<td>
<td>360×360dpi
<td>
<td>high resolution paper
<tr> <td>
<tr valign=top> <td>
<td><code>bjc610b1.upp</code>
<td>
<td>720×720dpi
<td>
<td>plain paper
<tr valign=top> <td>
<td><code>bjc610b2.upp</code>
<td>
<td>720×720dpi
<td>
<td>coated paper
<tr valign=top> <td>
<td><code>bjc610b3.upp</code>
<td>
<td>720×720dpi
<td>
<td>transparency film
<tr valign=top> <td>
<td><code>bjc610b4.upp</code>
<td>
<td>720×720dpi
<td>
<td>back print film
<tr valign=top> <td>
<td><code>bjc610b6.upp</code>
<td>
<td>720×720dpi
<td>
<td>glossy paper
<tr valign=top> <td>
<td><code>bjc610b7.upp</code>
<td>
<td>720×720dpi
<td>
<td>high-gloss paper
<tr valign=top> <td>
<td><code>bjc610b8.upp</code>
<td>
<td>720×720dpi
<td>
<td>high resolution paper
<tr> <td>
<tr> <th align=left colspan=6>HP Ink-Printers
<tr valign=top> <td>
<td><code>cdj550.upp</code>
<td>
<td>300×300dpi
<td>
<td>32-bit CMYK
<tr valign=top> <td>
<td><code>cdj690.upp</code>
<td>
<td>300×300dpi
<td>
<td>Normal mode
<tr valign=top> <td>
<td><code>cdj690ec.upp</code>
<td>
<td>300×300dpi
<td>
<td>Economy mode
<tr valign=top> <td>
<td><code>dnj750c.upp</code>
<td>
<td>300×300dpi
<td>
<td>Color -- also good for 450C
<tr valign=top> <td>
<td><code>dnj750m.upp</code>
<td>
<td>600×600dpi
<td>
<td>Monochrome
<tr> <td>
<tr> <th align=left colspan=6>NEC P2X
<tr valign=top> <td>
<td><code>necp2x.upp</code>
<td>
<td>360×360dpi
<td>
<td>8-bit (Floyd-Steinberg)
<tr> <td>
<tr> <th align=left colspan=6>Any Epson Stylus Color
<tr valign=top> <td>
<td><code>stcany.upp</code>
<td>
<td>360×360dpi
<td>
<td>4-bit, PostScript halftoning
<tr valign=top> <td>
<td><code>stcany_h.upp</code>
<td>
<td>720×720dpi
<td>
<td>4-bit, PostScript halftoning
<tr> <td>
<tr> <th align=left colspan=6>Original Epson Stylus and Stylus Pro Color
<tr valign=top> <td>
<td><code>stc.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, 15-pin
<tr valign=top> <td>
<td><code>stc_l.upp</code>
<td>
<td>360×360dpi
<td>
<td>4-bit, PostScript halftoning, weaved noWeave
<tr valign=top> <td>
<td><code>stc_h.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, 15-pin Weave
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color II
<tr valign=top> <td>
<td><code>stc2.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, 20-pin, Epson Stylus Color II(s)
<tr valign=top> <td>
<td><code>stc2_h.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, 20-pin, Epson Stylus Color II
<tr valign=top> <td>
<td><code>stc2s_h.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, 20-pin, Epson Stylus Color IIs
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 200
<tr valign=top> <td>
<td><code>stc200.upp</code>
<td>
<td>360×720dpi
<td>
<td>Plain Paper
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 300
<tr valign=top> <td>
<td><code>stc300.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, plain paper
<tr valign=top> <td>
<td><code>stc300bl.upp</code>
<td>
<td>180×180dpi
<td>
<td>black only, plain paper
<tr valign=top> <td>
<td><code>stc300bm.upp</code>
<td>
<td>360×360dpi
<td>
<td>black only, plain paper
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 500 (good transfer curves for plain paper)
<tr valign=top> <td>
<td><code>stc500p.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, noWeave, plain paper
<tr valign=top> <td>
<td><code>stc500ph.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, noWeave, plain paper
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 600, 32/90-inch weaving
<tr valign=top> <td>
<td><code>stc600pl.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, 32-pin, plain paper
<tr valign=top> <td>
<td><code>stc600p.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, 32-pin, plain paper
<tr valign=top> <td>
<td><code>stc600ih.upp</code>
<td>
<td>1440×720dpi
<td>
<td>32-bit CMYK, 30-pin, inkjet paper
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 640
<tr valign=top> <td>
<td><code>stc640p.upp</code>
<td>
<td>720×720dpi
<td>
<td>plain paper?
<tr valign=top> <td>
<td><code>st640p.upp</code>
<td>
<td>720×720dpi
<td>
<td>CMYK, plain paper
<tr valign=top> <td>
<td><code>st640pg.upp</code>
<td>
<td>720×720dpi
<td>
<td>grayscale, plain paper
<tr valign=top> <td>
<td><code>st640pl.upp</code>
<td>
<td>360×360dpi
<td>
<td>CMYK, plain paper
<tr valign=top> <td>
<td><code>st640plg.upp</code>
<td>
<td>360×360dpi
<td>
<td>grayscale, plain paper
<tr valign=top> <td>
<td><code>st640ih.upp</code>
<td>
<td>1440×720dpi
<td>
<td>CMYK, inkjet paper
<tr valign=top> <td>
<td><code>st640ihg.upp</code>
<td>
<td>1440×720dpi
<td>
<td>grayscale, inkjet paper
<tr> <td>
<tr> <th align=left colspan=6>Epson Stylus Color 800, 64/180-inch weaving
<tr valign=top> <td>
<td><code>stc800pl.upp</code>
<td>
<td>360×360dpi
<td>
<td>32-bit CMYK, 64-pin, plain paper
<tr valign=top> <td>
<td><code>stc800p.upp</code>
<td>
<td>720×720dpi
<td>
<td>32-bit CMYK, 64-pin, plain paper
<tr valign=top> <td>
<td><code>stc800ih.upp</code>
<td>
<td>1440×720dpi
<td>
<td>32-bit CMYK, 62-pin, inkjet paper
<tr valign=top> <td>
<td><code>stc1520.upp</code>
<td>
<td>1440×720dpi
<td>
<td>32-bit CMYK, 62-pin, inkjet paper
<tr> <td>
<tr> <th align=left colspan=6>Sun raster file
<tr valign=top> <td>
<td><code>ras1.upp</code>
<td>
<td>1-bit
<td>
<td>monochrome (Ghostscript)
<tr valign=top> <td>
<td><code>ras3.upp</code>
<td>
<td>3-bit
<td>
<td>RGB (Ghostscript)
<tr valign=top> <td>
<td><code>ras4.upp</code>
<td>
<td>4-bit
<td>
<td>CMYK (Ghostscript)
<tr valign=top> <td>
<td><code>ras8m.upp</code>
<td>
<td>8-bit
<td>
<td>grayscale (Floyd-Steinberg)
<tr valign=top> <td>
<td><code>ras24.upp</code>
<td>
<td>24-bit
<td>
<td>RGB (Floyd-Steinberg)
<tr valign=top> <td>
<td><code>ras32.upp</code>
<td>
<td>32-bit
<td>
<td>CMYK (CMYK-Floyd-Steinberg)
</table></blockquote>
<p>
Thanks to Danilo Beuche, Guido Classen, Mark Goldberg and Hans-Heinrich
Viehmann for providing the files for the stc200, hp690, stc500 and the
stc640. Thanks to Michael Lossin <losse@germanymail.com> for the
newer st640 parameter sets.
<p>
Please note the following:
<blockquote><ul>
<li>Changing the resolution with Ghostscript's
<a href="Use.htm#Resolution_switch"><code>-r</code> switch</a> is
usually not possible.
<li>For Epson Stylus Color models not listed above, the two
<code>stc500</code> variants are likely to work in addition to
<code>stcany</code>, but their gamma correction might be wrong.
</ul></blockquote>
<h3><a name="Uni_state"></a>The state of this driver</h3>
<p>
The coding of <code>uniprint</code> was triggered by the requirements of
the various Stylus Color models and some personal needs for HP and NEC
drivers. Thus the Epson models are well represented among the distributed
parameter files. When this driver entered the beta test phase, three other
drivers appreared on the scene that could be at least partially integrated
into <code>uniprint</code>: <code>cdj850</code> by Uli Wortmann
(available at <a href="http://www.erdw.ethz.ch/~bonk/hp850/hp850.html">http://www.erdw.ethz.ch/~bonk/hp850/hp850.html</a>),
<code>hpdj</code> by Martin Lottermoser, and <code>bjc610</code> by
Helmut Riegler.
<p>
Uli addresses features of the more recent DeskJet models that will not be
available in <code>uniprint</code> soon. Martin taught me a lesson on
HP-PCL3 headers that will be available in <code>uniprint</code>
soon. Helmut in turn followed an almost similar idea, but targetted
primarily for printing on Canon printers from the pbmplus library. Starting
with version 1.68 of uniprint, BJC support is available. Work on the
<code>hpdj</code> integration will start after the update of my website.
<h3><a name="Uni_background"></a>Notes on <code>uniprint</code>'s background</h3>
<p>
<code>uniprint</code> is actually an update of <code>stcolor</code>,
but much more versatile than its predecessor; <code>stcolor</code>, in
its turn, started as a clone of the color DeskJet family of drivers
(<code>cdj</code>*). Finally, <code>cdj</code>* can be considered an
addition of features to the simpler monochrome drivers of Ghostscript. This
addition of features is useful to get an idea of the functionality of
<code>uniprint</code>:
<blockquote>
<dl>
<dt>Monochrome to advanced color (<code>cdj</code>*):
<dd>This adds color mapping and rendering functions to the driver.
Error diffusion is especially important for the quality of printing.
</dl>
<dl>
<dt>HP color to Epson Color (<code>stcolor</code>)
<dd>The Epson Stylus Color offered two features simultaneously: it could
produce 720×720dpi output and it could soak the paper. In other
words, it required more color management features inside the driver. This
is still the major conceptual difference in the data generation for HP and
Epson printers.
</dl>
<dl>
<dt>Weaving techniques (<code>stcolor</code>)
<dd>Besides the internal color management, the Stylus Color did not provide
enough buffer space to operate the printer fast at 720×720dpi. The
use of weaving could yield triple the print speed. Weaving, also called
interleaving, is present in some monochrome drivers too. The new thing in
<code>stcolor</code> was the combination with error diffusion.
Unfortunately the weaving was somehow hard-coded, as the problems with the
newer members of the Stylus Color family of printers demonstrated.
</dl>
<dl>
<dt>Generalized output format and weaving (<code>uniprint</code>)
<dd>The features mentioned above yield about 90% of
<code>stcolor</code>'s source code; only 10% is related to the
formatting of the output. The idea to make the output format switchable
came up soon after completing <code>stcolor</code>, but its final design
was triggered by the (personal) necessity to drive a NEC P2X and a
Designjet 750c.
</dl></blockquote>
<p>
Thus <code>uniprint</code> accumulates almost any features that can be
found among the other printer drivers, which clearly has some disadvantage
in processing speed -- true in particular of version 1.75, since it was
targetted for functionality, and several speed-gaining features were
(knowingly) omitted.
<p>
To summarize and to introduce the terms used in the description of the
parameters, the features of <code>uniprint</code> that can be
parameterized are:
<blockquote><ul>
<li>color mapping,
<li>color rendering (error diffusion or Floyd-Steinberg),
<li>output format, including
<li>weaving.
</ul></blockquote>
<h3><a name="Uni_make_pfile"></a>Godzilla's guide to the creation of Unified Printer Parameter (<code>.upp</code>) files</h3>
<p>
Here is one of the distributed parameter files (<code>stc_l.upp</code>)
with some added comments. Also see the section that describes
<a href="#Uni_all_parameters">all <code>uniprint</code>'s parameters in
brief</a>.
<pre>
-supModel="Epson Stylus Color I (and PRO Series), 360x360DpI, noWeave"
-sDEVICE=uniprint -- Select the driver
-dNOPAUSE -- Useful with printers
-dSAFER -- Provides some security
-dupColorModel=/DeviceCMYK -- Selects the color mapping
-dupRendering=/ErrorDiffusion -- Selects the color rendering
-dupOutputFormat=/EscP2 -- Selects the output format
-r360x360 -- Adjusts the resolution
-dupMargins="{ 9.0 39.96 9.0 9.0}" -- Establishes (L/B/R/T margins in points)
-dupComponentBits="{1 1 1 1}" -- Map: bits per component (default: 8)
-dupWeaveYPasses=4 -- Weave: Y-passes (default: 1)
-dupOutputPins=15 -- Format/weave: scans per Command
-dupBeginPageCommand="< -- Goes to the printer
1b40 1b40 -- ESC '@' ESC '@' -> dual reset
1b2847 0100 01 -- ESC '(' 'G' 1 0 1 -> graphics
1b2869 0100 00 -- ESC '(' 'i' 1 0 1 -> no HW weave
1b2855 0100 0A -- ESC '(' 'U' 1 0 10 -> 360dpi
1b5500 -- ESC 'U' 0 -> bidir print
1b2843 0200 0000 -- ESC '(' 'C' 2 0 xx -> page length
1b2863 0400 0000 0000 -- ESC '(' 'c' 4 0 xxxx -> margins
>" -- as it is, unless:
-dupAdjustPageLengthCommand -- Adjust page length in BOP requested
-dupAdjustTopMarginCommand -- Adjust top margin in BOP
-dupAdjustBottomMarginCommand -- Adjust bottom margin in BOP
-dupEndPageCommand="(\033@\014)" -- Last (but one) data to the printer
-dupAbortCommand="(\033@\15\12\12\12\12 Printout-Aborted\15\014)"
</pre>
<p>
That's short, and if one removes <code>upWeaveYPasses</code> and
<code>upOutputPins</code> it becomes shorter, almost
<code>stcany.upp</code>. This miniature size is because I am most
familiar with ESC/P2, and was able to add defaults for the omitted
parameters. Now a few notes about the parameters used in this example:
<ul>
<li><code>upModel</code> is a string serving as a comment (and nothing else).
<li><a href="Use.htm#Output_device"><code>DEVICE</code></a>,
<a href="Use.htm#NoPause"><code>NOPAUSE</code></a>, <a
href="Use.htm#Safer"><code>SAFER</code></a> are well-known Ghostscript
parameters described in the <a href="Use.htm">usage documentation</a>.
<li><code>upColorModel</code> is one of major <code>uniprint</code>
parameters: it selects the color mapping and in turn the PostScript color
model. It supports the devices <code>/DeviceGray</code>, <code>/DeviceRGBW</code>, <code>/DeviceRGB</code>, <code>/DeviceCMYK</code>, and <code>/DeviceCMYKgenerate</code>.
<li><code>upRendering</code> selects the (color) rendering, supporting
the values <code>/ErrorDiffusion</code> and <code>/FSCMYK32</code>.
<code>/ErrorDiffusion</code> is similar to <code>fsmono</code>,
<code>fsrgb</code> and <code>fsx4</code> of <code>stcolor</code>,
while <code>/FSCMYK32</code> is (almost) identical to
<code>fscmyk</code> and <code>hscmyk</code>, but is restricted to
32-bit data and should be used in conjunction with
<code>/DeviceCMYKgenerate</code>.
<li><code>upOutputFormat</code> selects the output method, supporting the values
<code>/SunRaster</code>, <code>/Epson</code>, <code>/EscP2</code>, <code>/EscP2XY</code>, and<code>/Pcl</code>.
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td><code>/SunRaster</code>
<td>
<td>creates Sun raster files and requires no other parameters
<tr valign=top> <td><code>/Epson</code>
<td>
<td>is used for the elderly ESC/P format (used by many printers)
<tr valign=top> <td><code>/EscP2</code>
<td>
<td>is used by more recent Epson printers (no X weaving supported)
<tr valign=top> <td><code>/EscP2XY</code>
<td>
<td>supports X-Weaving, used with 1440dpi printers and in <code>stc2s_h</code>
<tr valign=top> <td><code>/Pcl</code>
<td>
<td>HP PCL/RTL-style output formatter without weaving
</table></blockquote>
<li><code>-r360x360</code> is Ghostscript's standard
<a href="Use.htm#Resolution_switch">resolution switch</a>.
<li><code>upMargins="{ 9.0 39.96 9.0 9.0}"</code>
has function similar to the Ghostscript parameter
<code>.HWMargins</code>: it sets the left, bottom, right, and top
margins in points. <code>uniprint</code> provides this parameter to
enable automatic left-right exchange if <code>upYFlip</code> is active.
<li><code>upComponentBits</code> is an array of integers that selects
the bits stored in raster memory, by default 8 bits per component. In this
example, 1 bit is selected for each component, thus turning down the
Floyd-Steinberg algorithm (but still carrying out the time-consuming
computation). The related parameter "<code>upComponentShift</code>"
controls positioning the components within raster memory. Each of the
numbers given corresponds to a component which depends on the selected
"<code>upColorModel</code>":
<blockquote><table cellpadding=0 cellspacing=0>
<tr valign=top> <td align=center>
<td>
<td align=center><code>/DeviceGray</code>
<td>
<td align=center><code>/DeviceRGBW</code>
<td>
<td align=center><code>/DeviceRGB</code>
<td>
<td align=center><code>/DeviceCMYK</code>
<td>
<td align=center><code>/DeviceCMYKgenerate</code>
<tr> <td colspan=11><hr>
<tr valign=top> <td align=center>0
<td>
<td align=center>White
<td>
<td align=center>White
<td>
<td align=center>Red
<td>
<td align=center>Black
<td>
<td align=center>Black
<tr valign=top> <td align=center>1
<td>
<td align=center>--
<td>
<td align=center>Red
<td>
<td align=center>Green
<td>
<td align=center>Cyan
<td>
<td align=center>Cyan
<tr valign=top> <td align=center>2
<td>
<td align=center>--
<td>
<td align=center>Green
<td>
<td align=center>Blue
<td>
<td align=center>Magenta
<td>
<td align=center>Magenta
<tr valign=top> <td align=center>3
<td>
<td align=center>--
<td>
<td align=center>Blue
<td>
<td align=center>--
<td>
<td align=center>Yellow
<td>
<td align=center>Yellow
</table>
<p>
This order may not be suitable for some printers, so another parameter
"<code>upOutputComponentOrder</code>", also an array of integers,
selects the output order using the numbers on the left.
</blockquote>
<p>
One group of very important parameters not used in the example above
deserves to be mentioned here: the transfer arrays, named
"<code>up<em>{color}</em>Transfer</code>", where
<code><em>{color}</em></code> is one of the names in the table above.
These are
arrays of floats in the range 0.0 - 1.0 representing the color transfer
functions. They are used during mapping and rendering. In the simplest
case, these arrays ensure an equidistant distribution of the stored values
within the device space (which means a nonlinear mapping from Ghostscript's
point of view). If the given array does not cover the entire range from 0
to 1, which applies for the Stylus Color family at high resolution for some
media, only the relevant part gets mapped to raster memory (meaning that
is's fully utilized) and the rendering takes care of the "overhang" (in
this case the post-diffusion of 1-bit components makes sense).
<p>
Finally an important note on the transfer arrays: for monochrome devices
the stored component is <code>White</code>, which is the way PostScript
defines these devices, but most printers require <code>Black</code>.
Thus one has to provide a falling "<code>upWhiteTransfer</code>" for
such printers.
<li><code>upWeaveYPasses</code> is an integer that gives the number of
print head passes required to achieve the requested Ydpi. This makes sense
only if
<li><code>upOutputPins</code> is set to something greater than 1. Thus
multiple pins or nozzles are transferred with a single command, and of
course such a command must be supported by the device.
</ul>
<p>
If no other weave parameters are given, <code>uniprint</code> computes
several defaults which together do no weaving. The <code>/Epson</code>
and <code>/EscP2XY</code> formats take care of
"<code>upWeaveXPasses</code>" too.
<ul>
<li><code>upBeginPageCommand</code> represents the data transferred to
the printer whenever a new page begins. Before that,
"<code>upBeginJobCommand</code>" is written to the device only once per
output file. (Intended for the HP PJL sequences).
<li><code>upAdjustBottomMarginCommand</code>,
<code>upAdjustMediaSize</code>,
<code>upAdjustPageLengthCommand</code>,
<code>upAdjustPageWidthCommand</code>,
<code>upAdjustResolutionCommand</code>, and
<code>upAdjustTopMarginCommand</code>
<p>
Normally <code>uniprint</code> does not change the
"<code>upBeginPageCommand</code>", nor does it provide a default.
However, if the above boolean values are set, the corresponding values are
changed (provided that the code of the formatters supports this change and
the commands to be adjusted are included in the BOP string).
<li><code>upEndPageCommand</code> is the fixed termination sequence for
each page, and of course there is an "<code>upEndJobCommand</code>" too.
<li><code>upAbortCommand</code> is written if <code>uniprint</code>'s
interrupt detection is enabled and a signal is caught. It replaces
"<code>upEndPageCommand</code>" and "<code>upEndJobCommand</code>",
thus allowing the indication of an aborted job. (Ghostscript gets an error
return from <code>uniprint</code> in this case, and abandons further
processing.)
</ul>
<p>
For the ESC/P(2) formats all commands represent binary data, while for
the PCL/RTL formatter some of them are formats for <code>fprintf</code>. These strings
<b><em>must</em></b> explicitly have a trailing "\0'.
<p>
I should write more, but the only recommendation is to
take a look at the various parameter files. Here are a few more hints.
<ul>
<li>If the Driver rejects a configuration, nothing happens until
<code>showpage</code>; then an error is raised and a message with
"CALL-REJECTED upd_print_page..." is printed on stderr.
<li><code>uniprint</code> has lots of messages that can be activated by
setting bits in the preprocessor macro <code>UPD_MESSAGES</code>. I
usually use the compile-time option <code>-DUPD_MESSAGES=0x17</code> for
configuration development. (For the semantics, check the
<code>UPD_M_</code> macros in the source.)
<li>A program "<code>uninfo.ps</code>" distributed with Ghostscript
displays interactively in alphabetical order the contents of the current
pagedevice dictionary. This includes any parameters generated or changed by
<code>uniprint</code>.
</ul>
<h3><a name="Uni_all_parameters"></a>All parameters in brief</h3>
<p>
This table gives a brief explanation of every parameter known to
<code>uniprint</code>, listing them in alphabetical order. "[ ]"
denotes that a parameter is an array, and "(RO)" that it is read-only.
<blockquote><table cellpadding=0 cellspacing=0>
<tr><th colspan=5 bgcolor="#CCCC00"><hr><font size="+1">All <code>uniprint</code> parameters</font><hr>
<tr valign=bottom>
<th align=left>Parameter
<td>
<th align=left>Type
<td>
<th align=left>Use
<tr> <td colspan=5><hr>
<tr valign=top> <td><code>upAbortCommand</code>
<td>
<td>String
<td>
<td>End of page and file on interrupt
<tr valign=top> <td><code>upAdjustBottomMarginCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate bottom margin in <code>upBeginPageCommand</code>
<tr valign=top> <td><code>upAdjustMediaSizeCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate <code>Mediasize</code> [intended]
<tr valign=top> <td><code>upAdjustPageLengthCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate page length in <code>upBeginPageCommand</code>
<tr valign=top> <td><code>upAdjustPageWidthCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate page width in <code>upBeginPageCommand</code>
<tr valign=top> <td><code>upAdjustResolutionCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate resolution
<tr valign=top> <td><code>upAdjustTopMarginCommand</code>
<td>
<td>Bool
<td>
<td>Manipulate top margin in <code>upBeginPageCommand</code>
<tr valign=top> <td><code>upBeginJobCommand</code>
<td>
<td>String
<td>
<td>Begin each output file
<tr valign=top> <td><code>upBeginPageCommand</code>
<td>
<td>String
<td>
<td>Begin each page
<tr valign=top> <td><code>upBlackTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Black transfer (CMYK only!)
<tr valign=top> <td><code>upBlueTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Blue transfer
<tr valign=top> <td><code>upColorInfo</code>
<td>
<td>Int[ ]
<td>
<td>struct <code>gx_device_color_info</code>
<tr valign=top> <td><code>upColorModel</code>
<td>
<td>Name
<td>
<td>Select color mapping
<tr valign=top> <td><code>upColorModelInitialized</code>
<td>
<td>Bool (RO)
<td>
<td>Color mapping OK
<tr valign=top> <td><code>upComponentBits</code>
<td>
<td>Int[ ]
<td>
<td>Bits stored per component
<tr valign=top> <td><code>upComponentShift</code>
<td>
<td>Int[ ]
<td>
<td>Positioning within <code>gx_color_index</code>
<tr valign=top> <td><code>upCyanTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Cyan transfer
<tr valign=top> <td><code>upEndJobCommand</code>
<td>
<td>String
<td>
<td>End each file unless <code>upAbortCommand</code>
<tr valign=top> <td><code>upEndPageCommand</code>
<td>
<td>String
<td>
<td>End each page unless <code>upAbortCommand</code>
<tr valign=top> <td><code>upErrorDetected</code>
<td>
<td>Bool (RO)
<td>
<td>Severe (VM) error, not fully operational
<tr valign=top> <td><code>upFSFixedDirection</code>
<td>
<td>Bool
<td>
<td>Inhbits direction toggling in rendering
<tr valign=top> <td><code>upFSProcessWhiteSpace</code>
<td>
<td>Bool
<td>
<td>Causes white-space rendering
<tr valign=top> <td><code>upFSReverseDirection</code>
<td>
<td>Bool
<td>
<td>Run rendering in reverse (if fixed)
<tr valign=top> <td><code>upFSZeroInit</code>
<td>
<td>Bool
<td>
<td>Non-random rendering initialization
<tr valign=top> <td><code>upFormatXabsolute</code>
<td>
<td>Bool
<td>
<td>Write absolute X coordinates
<tr valign=top> <td><code>upFormatYabsolute</code>
<td>
<td>Bool
<td>
<td>Write absolute Y coordinates
<tr valign=top> <td><code>upGreenTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Green transfer
<tr valign=top> <td><code>upMagentaTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Magenta transfer
<tr valign=top> <td><code>upMargins</code>
<td>
<td>Float[ ]
<td>
<td>L/B/R/T margins in points
<tr valign=top> <td><code>upModel</code>
<td>
<td>String
<td>
<td>Comment string, holds some info
<tr valign=top> <td><code>upOutputAborted</code>
<td>
<td>Bool (RO)
<td>
<td>Caught an interrupt
<tr valign=top> <td><code>upOutputBuffers</code>
<td>
<td>Int
<td>
<td>Number of rendering buffers (2^<small><sup><b>N</b></sup></small>)
<tr valign=top> <td><code>upOutputComponentOrder</code>
<td>
<td>Int[ ]
<td>
<td>Order of components when printing
<tr valign=top> <td><code>upOutputComponents</code>
<td>
<td>Int
<td>
<td>Number of written components, not fully operational
<tr valign=top> <td><code>upOutputFormat</code>
<td>
<td>Name
<td>
<td>Select output format
<tr valign=top> <td><code>upOutputFormatInitialized</code>
<td>
<td>Bool (RO)
<td>
<td>Format data OK
<tr valign=top> <td><code>upOutputHeight</code>
<td>
<td>Int
<td>
<td>Output height in pixels
<tr valign=top> <td><code>upOutputPins</code>
<td>
<td>Int
<td>
<td>Number of pins / nozzles per command
<tr valign=top> <td><code>upOutputWidth</code>
<td>
<td>Int
<td>
<td>Output width in pixels
<tr valign=top> <td><code>upOutputXOffset</code>
<td>
<td>Int
<td>
<td>Offset in pixels, if <code>upFormatXabsolute</code>
<tr valign=top> <td><code>upOutputXStep</code>
<td>
<td>Int
<td>
<td>Divisor or multiplier for X coords
<tr valign=top> <td><code>upOutputYOffset</code>
<td>
<td>Int
<td>
<td>Offset in pixels, if <code>upFormatYabsolute</code>
<tr valign=top> <td><code>upOutputYStep</code>
<td>
<td>Int
<td>
<td>Divisor or multiplier for Y coords
<tr valign=top> <td><code>upRasterBufferInitialized</code>
<td>
<td>Bool (RO)
<td>
<td>GS buffer OK
<tr valign=top> <td><code>upRedTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Red transfer
<tr valign=top> <td><code>upRendering</code>
<td>
<td>Name
<td>
<td>Select rendering algorithm
<tr valign=top> <td><code>upRenderingInitialized</code>
<td>
<td>Bool (RO)
<td>
<td>Rendering parameters OK
<tr valign=top> <td><code>upSelectComponentCommands</code>
<td>
<td>String[ ]
<td>
<td>Establish color (output order!)
<tr valign=top> <td><code>upSetLineFeedCommand</code>
<td>
<td>String
<td>
<td>Adjust linefeed (Epson only)
<tr valign=top> <td><code>upVersion</code>
<td>
<td>String (RO)
<td>
<td>Source code version
<tr valign=top> <td><code>upWeaveFinalPins</code>
<td>
<td>Int[ ]
<td>
<td>Number of bottom pins on EOP passes
<tr valign=top> <td><code>upWeaveFinalScan</code>
<td>
<td>Int
<td>
<td>Begin EOP passes (Y-coord)
<tr valign=top> <td><code>upWeaveFinalXStarts</code>
<td>
<td>Int[ ]
<td>
<td>X-pass indices for EOP passes
<tr valign=top> <td><code>upWeaveFinalYFeeds</code>
<td>
<td>Int[ ]
<td>
<td>Y increments for EOP passes
<tr valign=top> <td><code>upWeaveInitialPins</code>
<td>
<td>Int[ ]
<td>
<td>Number of top pins on BOP passes
<tr valign=top> <td><code>upWeaveInitialScan</code>
<td>
<td>Int
<td>
<td>End BOP passes (Y coord)
<tr valign=top> <td><code>upWeaveInitialXStarts</code>
<td>
<td>Int[ ]
<td>
<td>X-pass indices for BOP passes
<tr valign=top> <td><code>upWeaveInitialYFeeds</code>
<td>
<td>int[ ]
<td>
<td>Y increments for BOP passes
<tr valign=top> <td><code>upWeavePasses</code>
<td>
<td>Int
<td>
<td>XPasses × YPasses
<tr valign=top> <td><code>upWeaveXPasses</code>
<td>
<td>Int
<td>
<td>Number of X passes
<tr valign=top> <td><code>upWeaveXStarts</code>
<td>
<td>Int[ ]
<td>
<td>X-pass indices for normal passes
<tr valign=top> <td><code>upWeaveYFeeds</code>
<td>
<td>Int[ ]
<td>
<td>Y increments for normal passes
<tr valign=top> <td><code>upWeaveYOffset</code>
<td>
<td>Int
<td>
<td>Number of blank or incomplete scans at BOP
<tr valign=top> <td><code>upWeaveYPasses</code>
<td>
<td>Int
<td>
<td>Number of X passes
<tr valign=top> <td><code>upWhiteTransfer</code>
<td>
<td>Float[ ]
<td>
<td>White transfer (monochrome devices!)
<tr valign=top> <td><code>upWriteComponentCommands</code>
<td>
<td>String[ ]
<td>
<td>Commands to write each component
<tr valign=top> <td><code>upWroteData</code>
<td>
<td>Bool (RO)
<td>
<td>Something (<code>BeginJob</code>) written to output
<tr valign=top> <td><code>upXMoveCommand</code>
<td>
<td>String
<td>
<td>X positioning command
<tr valign=top> <td><code>upXStepCommand</code>
<td>
<td>String
<td>
<td>Single step to the right
<tr valign=top> <td><code>upYFlip</code>
<td>
<td>Bool
<td>
<td>Flips output along the Y axis
<tr valign=top> <td><code>upYMoveCommand</code>
<td>
<td>String
<td>
<td>Y positioning command
<tr valign=top> <td><code>upYStepCommand</code>
<td>
<td>String
<td>
<td>Single step down
<tr valign=top> <td><code>upYellowTransfer</code>
<td>
<td>Float[ ]
<td>
<td>Yellow transfer
</table></blockquote>
<h3><a name="Uni_honors"></a><code>uniprint</code>'s Roll of Honor</h3>
<p>
I should mention all of the people who were involved in
<code>stcolor</code>'s evolution, but I've decided to start from scratch
here for <code>uniprint</code>:
<blockquote>
<dl>
<dt>John P. Beale
<dd>for testing the <code>stc600</code> modes
<dt>Bill Davidson
<dd>who triggered some weaving research and tested <code>stc2s_h</code>
<dt>L. Peter Deutsch
<dd>who triggered ease of configuration
<dt>Mark Goldberg
<dd>who prepared the <code>stc500</code> transfers
<dt>Scott F. Johnston and Scott J. Kramer
<dd>for testing the <code>stc800</code> modes
<dt>Martin Lottermoser
<dd>for his great commented H-P DeskJet driver
<dt>Helmut Riegler
<dd>for the BJC extension
<dt>Hans-Gerd Straeter
<dd>for some measured transfer curves and more
<dt>Uli Wortmann
<dd>for discussions and his <code>cdj850</code> driver
<dt>My family
<dd>for tolerating my printer-driver hacking
</dl>
</blockquote>
<address>
Gunther Hess<br>
Duesseldorfer Landstr. 16b<br>
D-47249 Duisburg<br>
Germany<br>
+49 203 376273 telephone (MET evening hours)<br>
<<a href="mailto:ghess@elmos.de">ghess@elmos.de</a>>
</address>
<h3><a name="Uni_weaving_howto"></a><tt>Uniprint</tt> weaving parameters howto</h3>
This section was contributed by Glenn Ramsey.<p>
<p>I wrote this because the documentation was very brief and I really struggled
with it for a while, but it is very simple once you understand what is going
on.
<p>This only describes how to work out the Y parameters, I haven't looked
at the X parameters yet.
<ol>
<li>
<b>Determine the nozzle geometry (upOutputPins)</b>
<p>
You need to know how many nozzles the printer has and the spacing between
them. Usually you can find this out from the printer manual, or the printer
supplier, but you may have to dissect a couple of printer output files
produced with the driver supplied with the printer. There is a utility
called escp2ras<a href="#escp2ras"><sup>*</sup></a> that will help with that.
Sometimes the term pin is used instead of nozzle but they mean the same thing.
<p>The number of nozzles will be the value assigned to the upOutputPins
parameter.
<p>Actually you don't have to print with all the pins available but for
the purpose of demonstration I'll assume that we are using them all.
<p>
<a name="escp2ras"></a>* escp2ras is available from Gunther Hess' page at <a href="http://www-md.e-technik.uni-rostock.de/ma/gunther/gs/index.html">http://www-md.e-technik.uni-rostock.de/ma/gunther/gs/index.html</a>
<p>
</li>
<li><b>Determine how many passes are required (upWeaveYPasses)</b>
<p>The number of passes required is going to depend on the required resolution
and the nozzle spacing.
<blockquote>
<tt>passes = resolution * nozzle spacing
</tt>
</blockquote>
This will be the value assigned to the upWeaveYPasses parameter.
<p>For example if the desired resolution is 360 dpi and the nozzles are
spaced at 1/90in then 360 * 1/90 = 4 passes are required. For 720 dpi 8
passes would be required. The printer would, of course, have to be capable
of moving the paper in increments of either 360 or 720 dpi too.
<p>
</li>
<li>
<b>Determine the normal Y feed increment (upWeaveYFeeds)</b>
<p>
You need to work out how much to feed the paper so that when the paper
has moved by one head length in however many passes you have then each
row space on the paper has been passed over by at least one nozzle. There
will be one feed value for each pass and the feed values must comply with
the following rules:
<blockquote>
<p><tt>sum of feeds = passes * nozzles
<br>feed%passes != 0 (feed is not exactly divisible by passes)
<br>sum of (nozzles - feed) = 0
</tt>
</blockquote>
<p>For example if passes=4 and nozzles=15, then sum of feeds=60. The feed
values could be 1,1,1,57 or 15,15,15,15 or 14,15,18,13.
<p>These values will be assigned to the upWeaveYFeeds parameter.
<p>You would need to experiment to see what combination looks best on the
printer.
<p>I found it convenient to draw several lines of nozzles and then move
them around to see how the different combinations would fill the paper.
A computer drawing tool makes this easier than pencil and paper (I used
Dia, a GNOME app). The number of nozzles would probably be be a good place
to start.
<p>Remember that if the number of passes is more than 1 then the feed increment
will be less than the nozzle spacing and <tt>passes × feed increment size</tt>
must equal the physical distance between each nozzle.
<p>
</li>
<li>
<b>Determine the beginning of page pins (upWeaveInitialPins)</b>
<p>
These values will be assigned to the upWeaveInitialPins parameter and are
the numbers of nozzles to operate in each of the initial passes at the top
of a page. The nozzles that the values refer to are the topmost nozzles
on the head, nearest the top margin. If the image doesn't start at the
top margin then uniprint doesn't use these feeds.
<p>I don't know a mathematical relation for this except that at least one
of the values must be the number of nozzles, but I'm sure that there must
be one. I used a graphical method, the description that follows refers
to the ascii diagram in below.
<p>Draw a line of nozzles for each pass arranged as they would be using
the normal Y feed increment determined in step 3. In the diagram below
this would be passes 5-8.
<p>Draw a line of nozzles that would print just before the first normal
pass. The feed increment for this pass will be close to and most likely
1 or 2 units less than the feed increment of the last normal pass. In the
example below this line is pass 4 and the feed increment is 13 whereas
the normal feed increment is 15.
<p>Draw each pass before that with a small feed increment so that if all
of the nozzles appearing above the first nozzle of the first normal pass
operate then all of the spaces will be filled. This feed increment is usually
1 except in cases where some jiggery pokery is going on to make the printer
print at an apparent higher resolution than the nozzle diameter.
<p>Now select the nozzles that will operate in each of theses initial passes
so that the paper is filled. In each pass the nozzles must be adjacent
to each other and at least one of the passes will have all the nozzles
operating. I suspect that for each combination of normal Y feed increments
there will only be one set of valid beginning of page increments.
</li>
</ol>
<h4>Example: stc.upp from Aladdin Ghostscript 6.01</h4>
15 nozzles spaced at 1/90 in, 360 dpi requires 4 passes.
<blockquote><pre><tt>
-dupWeaveYPasses=4
-dupOutputPins=15
-dupWeaveYFeeds="{15 15 15 15}"
-dupWeaveInitialYFeeds="{1 1 1 13}"
-dupWeaveInitialPins="{ 4 15 11 7}"
</tt></pre></blockquote>
The following diagram shows which nozzles operate during each pass.
<br>Passes 1-4 are beginning of page passes and passes 5-8 are normal passes.
<blockquote>
<p>x=nozzle operates, o=nozzle not used in this pass<tt></tt>
<p><tt> 1 2 3 4 5 6 7 8 - pass no</tt>
<br><tt>0 x</tt>
<br><tt>1 x</tt>
<br><tt>2 x</tt>
<br><tt>3 x</tt>
<br><tt>4 x</tt>
<br><tt>5 x</tt>
<br><tt>6 x</tt>
<br><tt>7 x</tt>
<br><tt>8 x</tt>
<br><tt>9 x</tt>
<br><tt>0 x</tt>
<br><tt>1 x</tt>
<br><tt>2 x</tt>
<br><tt>3 x</tt>
<br><tt>4 x</tt>
<br><tt>5 x</tt>
<br><tt>6 o x</tt>
<br><tt>7 x</tt>
<br><tt>8 x</tt>
<br><tt>9 x</tt>
<br><tt>0 o x</tt>
<br><tt>1 x</tt>
<br><tt>2 x</tt>
<br><tt>3 x</tt>
<br><tt>4 o x</tt>
<br><tt>5 x</tt>
<br><tt>6 x</tt>
<br><tt>7 x</tt>
<br><tt>8 o x</tt>
<br><tt>9 x</tt>
<br><tt>0 x</tt>
<br><tt>1 o x</tt>
<br><tt>2 o x</tt>
<br><tt>3 x</tt>
<br><tt>4 x</tt>
<br><tt>5 o x</tt>
<br><tt>6 o x</tt>
<br><tt>7 x</tt>
<br><tt>8 x</tt>
<br><tt>9 o x</tt>
<br><tt>0 o x</tt>
<br><tt>1 x</tt>
<br><tt>2 x</tt>
<br><tt>3 o x</tt>
<br><tt>4 o x</tt>
<br><tt>5 x</tt>
<br><tt>6 o
x</tt>
<br><tt>7 o x</tt>
<br><tt>8 o x</tt>
<br><tt>9 x</tt>
<br><tt>0 o
x</tt>
<br><tt>1 o x</tt>
<br><tt>2 o x</tt>
<br><tt>3 x</tt>
<br><tt>4 o
x</tt>
<br><tt>5 o x</tt>
<br><tt>6 o x</tt>
<br><tt>7 x</tt>
<br><tt>8 o
x</tt>
<br><tt>9 o x</tt>
<br><tt>0 x</tt>
<br><tt>1
x</tt>
<br><tt>2
x</tt>
<br><tt>3 x</tt>
<br><tt>4 x</tt>
<br><tt>5
x</tt>
<br><tt>6
x</tt>
<br><tt>7 x</tt>
<br><tt>8 x</tt>
<br><tt>9
x</tt>
<br><tt>0
x</tt>
<br><tt>1 x</tt>
<br><tt>2 x</tt>
<br><tt>3
x</tt>
<br><tt>4
x</tt>
<br><tt>5 x</tt>
<br><tt>6</tt>
<br><tt>7
x</tt>
<br><tt>8
x</tt>
<br><tt>9 x</tt>
<br><tt>0</tt>
<br><tt>1
x</tt>
<br><tt>2
x</tt>
<br><tt>3 x</tt>
<br><tt>4</tt>
<br><tt>5
x</tt>
<br><tt>6
x</tt>
<br><tt>7 x</tt>
<br><tt>8</tt>
<br><tt>9
x</tt>
<br><tt>0
x</tt>
<br><tt>1</tt>
<br><tt>2</tt>
<br><tt>3
x</tt>
<br><tt>4
x</tt>
<br><tt>5</tt>
<br><tt>6</tt>
<br><tt>7
x</tt>
<br><tt>8
x</tt>
<br><tt>9</tt>
<br><tt>0</tt>
<br><tt>1
x</tt>
<br><tt>2
x</tt>
<br><tt>3</tt>
<br><tt>4</tt>
<br><tt>5
x</tt>
<br><tt>6</tt>
<br><tt>7</tt>
<br><tt>8</tt>
<br><tt>9
x</tt>
<br><tt>0</tt>
<br><tt>1</tt>
<br><tt>2</tt>
<br><tt>3
x</tt>
<br><tt>4</tt>
<br><tt>5</tt>
<br><tt>6</tt>
<br><tt>7
x</tt>
</blockquote>
<p>These parameters would also work:
<blockquote><pre><tt>
-dupWeaveYPasses=4
-dupOutputPins=15
-dupWeaveYFeeds="{14 15 18 13}"
-dupWeaveInitialYFeeds="{1 1 1 13}"
-dupWeaveInitialPins="{ 4 11 7 15}"
</tt></pre></blockquote>
<p>
<hr>
<h3><a name="Uni_esc300"></a>Extension to <tt>uniprint</tt> for the Epson Stylus Color 300</h3>
This section was contributed by Glenn Ramsey.<p>
The Epson Stylus Color 300 uses a different command set to other Epson
Stylus Color printers that use the ESC/P2 language. As far as I can
tell its commands are a subset of ESC/P2. In ESC/P2 the colour to be
printed is selected by a 'set colour' command and then the data sent
is only printed in that colour until the colour is changed with another
'set colour' command. The Stylus Color 300 lacks this functionality.
The data sent to the printer maps directly to the ink nozzles and colour
of an output scan line in the printed output is determined by the position
of the scan line within the data. This means that the driver must know
how the nozzles are arranged and must format the output accordingly.
The extension adds a format that I have called EscNozzleMap and adds some
additional parameters to uniprint.<br>
<ul>
<li><code>upOutputFormat</code>selects the output method, and should be set to the value
<code>/EscNozzleMap</code> to select this format.
<blockquote>
<table cellpadding="0" cellspacing="0">
<tbody>
<tr valign="Top">
<td><code>/EscNozzleMap</code></td>
<td> </td>
<td>produces output for the Epson Stylus Color 300
</td>
</tr>
</tbody>
</table>
</blockquote>
</ul>
<blockquote>
<table cellpadding="0" cellspacing="0">
<tbody>
<tr>
<th colspan="5" bgcolor="#cccc00">
<hr><font size="+1"><code>uniprint</code> parameters for the
EscNozzleMap format</font>
<hr></th>
</tr>
<tr valign="Bottom">
<th align="Left">Parameter
</th>
<td>
</td>
<th align="Left">Type
</th>
<td>
</td>
<th align="Left">Use
</th>
</tr>
<tr>
<td colspan="5">
<hr></td>
</tr>
<tr valign="Top">
<td><code>upNozzleMapRowsPerPass</code></td>
<td>
</td>
<td>Int
</td>
<td>
</td>
<td>output rows to generate for each pass of the head
</td>
</tr>
<tr valign="Top">
<td><code>upNozzleMapPatternRepeat</code></td>
<td>
</td>
<td>Int
</td>
<td>
</td>
<td>no. of rows that correspond to the repeat pattern of the
nozzles
</td>
</tr>
<tr valign="Top">
<td><code>upNozzleMapRowMask</code></td>
<td>
</td>
<td>Int[]
</td>
<td>
</td>
<td>mask indicating the colour of the nozzles
</td>
</tr>
<tr valign="Top">
<td><code>upNozzleMapMaskScanOffset</code></td>
<td>
</td>
<td>Int[]
</td>
<td>
</td>
<td>mask indicating the physical position of the nozzles
</td>
</tr>
</tbody>
</table>
</blockquote>
<h4>A more detailed description of the new parameters</h4>
<ul>
<li><code>upNozzleMapRowsPerPass</code><br>
The number of rows of data that are required to address all nozzles for a
single pass of the head. There will always be this number of rows of output
data generated. I'd expect it to be the same as the total number of nozzles but
it wouldn't break the formatter if it wasn't. So if you wanted to print with
only the 10th nozzle then row 10 would contain data corresponding to the bit
pattern and all of the others would be padded with zeros.
</li>
<li><code>upNozzleMapPatternRepeat</code><br>
The number of nozzles in each repeated group on the printing head.
This parameter must correspond with the length of the upNozzleMapRowMask array.
</li>
<li><code>upNozzleMapRowMask</code><br>
An array of integers that defines the colour of the nozzles on the
head and whether the nozzles will be used to print. The array index
defines the row index for the nozzle in the output data
and the value defines the colour of the nozzle. The mapping
of colours to values is defined in the table below.
<blockquote>
<table cellpadding="0" cellspacing="0">
<tbody>
<tr valign="Bottom">
<th align="Left">colour
</th>
<td>
</td>
<th align="center">mask value
</th>
</tr>
<tr>
<td colspan="5">
<hr></td>
</tr>
<tr valign="Top" align="center">
<td><code>K</code></td>
<td>
</td>
<td>1
</td>
</tr>
<tr valign="Top" align="center">
<td><code>C</code></td>
<td>
</td>
<td>2
</tr>
<tr valign="Top" align="center">
<td><code>M</code></td>
<td>
</td>
<td>3
</td>
</tr>
<tr valign="Top" align="center">
<td><code>Y</code></td>
<td>
</td>
<td>4
</td>
</tr>
<tr valign="Top" align="center">
<td><code>no data</code></td>
<td>
</td>
<td>0
</td>
</tr>
</tbody>
</table>
</blockquote>
A value of 0 means that the nozzle is not used and the row in the output data will be
padded with zeros.<br>
</li>
<li><code>upNozzleMapMaskScanOffset</code><br>
An array of integers that defines the physical position of the nozzles relative
to the first nozzle in the repeated group. The relative distance is measured in
printed line widths and will be different for different printing resolutions.
This parameter is used because the physical spacing of the nozzles may not
correspond to their mapping in the output data. For example the ESC300 has nozzles
physically arranged something like this:
<table>
<tr>
<td bgcolor="#00ffff">
</td>
<td bgcolor="#ffff00">
</td>
<td bgcolor="#000000">
</td>
<td bgcolor="#ff00ff">
</td>
<td bgcolor="#000000">
</td>
<td>
</td>
<td bgcolor="#000000">
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td bgcolor="#00ffff">
</td>
<td bgcolor="#ffff00">
</td>
<td bgcolor="#000000">
</td>
<td bgcolor="#ff00ff">
</td>
<td bgcolor="#000000">
</td>
<td>
</td>
<td bgcolor="#000000">
</td>
<td bgcolor="#ffffff">
</td>
</tr>
<tr>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td bgcolor="#00ffff">
</td>
<td bgcolor="#ffff00">
</td>
<td bgcolor="#000000">
</td>
<td bgcolor="#ff00ff">
</td>
<td bgcolor="#000000">
</td>
<td>
</td>
<td bgcolor="#000000">
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td>
</td>
<td bgcolor="#00ffff">
</td>
<td bgcolor="#ffff00">
</td>
<td>etc ...
</td>
</tr>
</table>
There is a one nozzle width space between the last two nozzles in each group.
In the output data the data for the last nozzle in the group would be in row 5
(numbering starts at 0) but the nozzle is physically positioned at 6 spaces from
the first nozzle.
</ul>
<h4>Example 1 - Epson Stylus Color 300 - 360 dpi colour</h4>
<blockquote><pre>
-dupWeaveYPasses=6
-dupOutputPins=11
-dupWeaveYFeeds="{ 11 11 11 11 11 11 }"
-dupWeaveInitialYFeeds="{ 1 1 1 1 1 7 }"
-dupWeaveInitialPins="{ 2 11 9 7 5 3 }"
-dupNozzleMapRowsPerPass=64
-dupNozzleMapPatternRepeat=6
-dupNozzleMapRowMask="{ 2 4 1 3 0 0 }"
-dupNozzleMapMaskScanOffset="{ 0 1 2 3 0 0 }"
</pre></blockquote>
The weaving parameters are the same as for any other uniprint driver
but they must be consistent with the nozzle map parameters. In this printer
the coloured nozzles are spaced at 1/60" so 6 passes are required for 360
dpi resolution.
<p>
In the example there are 64 rows of data required for each head pass. Each
row must be completely filled with data for each pass so if certain nozzles
do not print in the pass then the rows for those nozzles will be padded
with zeroes.
<P>
The row mask translates to "C Y K M 0 0" so in the output data rows 0,7,13,...
will contain data for cyan, rows 1,8,14,... will contain data for yellow, etc. Rows 4,10,16,...
and 5, 11,15,... will always be padded with zeroes. The <i>upNozzleMapPatternRepeat</i>
parameter defines the length of the mask.
<p>
The row mask is repeated for each group of <i>upNozzleMapPatternRepeat</i> rows
in the output data. In this case there are 64 rows so there will be 10 groups
of "C Y K M 0 0" followed by "C Y K M" which is equivalent to 11 output
pins.
<P>
The <i>upNozzleMaskScanOffset</i> array indicates how the data from the scan
buffer is mapped to the output data. The data is presented to the formatter
as a buffer of four colour scanlines. The index of the scanline being printed,
lets call it y, always corresponds, in this example, to the physical position of
the cyan nozzle but since the nozzles are not on the same horizontal
line then the other colours for the current pass must come from other
scanlines in the scan buffer. The example is { 0 1 2 3 0 0 }, this means that
when printing a 4 colour image the magenta data would come from scanline y+3,
the black from scanline y+2, etc. It would have been possible in this case
to use the array index instead of the <i>upNozzleMaskScanOffset</i> parameter
however the parameter is necessary to be able to use the full capability of the
printer in black only mode.
<h4>Example 2 - Epson Stylus Color 300 - 180 dpi black only</h4>
<blockquote>
<pre>
-dupMargins="{ 9.0 39.96 9.0 9.0}"
-dupWeaveYPasses=1
-dupOutputPins=31
-dupNozzleMapRowsPerPass=64
-dupNozzleMapPatternRepeat=6
-dupNozzleMapRowMask="{ 0 0 1 0 1 1}"
-dupNozzleMapMaskScanOffset="{ 0 0 0 0 1 2 }"
</pre>
</blockquote>
In this example there is no weaving.
<p>
The ESC300 has black nozzles evenly physically arranged as K K K but the data must
be sent to the printer as 00K0KK. This is handled by the <i>upNozzleMapRowMask</i>
and <i>upNozzleMaskScanOffset</i> arrays. The <i>upNozzleMapRowMask</i> array is
{ 0 0 1 0 1 1} which translates to { 0 0 K 0 K K } so rows 0, 1 and 3 will always
contain zeros and the other rows will contain data.
<p>
The <i>upNozzleMaskScanOffset</i> array
in this case is { 0 0 0 0 1 2 } so if the data for the 1st nozzle comes from row
y in the scan buffer then the data for the 2nd and 3rd nozzles will come from rows
y+1 and y+2.
<h4>Example 3 - Epson Stylus Color 300 - 360 dpi black only</h4>
<blockquote>
<pre>
-dupWeaveYPasses=2
-dupOutputPins=31
-dupWeaveYFeeds="{31 31}"
-dupWeaveInitialYFeeds="{1 31}"
-dupWeaveInitialPins="{16 31}"
-dupNozzleMapRowsPerPass=64
-dupNozzleMapPatternRepeat=6
-dupNozzleMapRowMask="{ 0 0 1 0 1 1}"
-dupNozzleMapMaskScanOffset="{ 0 0 0 0 2 4 }"
</pre>
</blockquote>
In this example 2 weave passes are required to achieve the desired resolution.
<p>
The <i>upNozzleMaskScanOffset</i> array in this case is { 0 0 0 0 2 4 } because
there are two weave passes so if the data for the first nozzle comes from row y
in the scan buffer then the data for the 2nd and 3rd nozzles must come from rows
y+(1*2) and y+(2*2).
<p>
<address>
Glenn Ramsey<br>
glennr at users.sourceforge.net<br>
February 2001
</address>
<br>
<!-- [3.0 begin visible trailer] =========================================== -->
<hr>
<p>
<small>Copyright © 2000-2006 Artifex Software, Inc. All rights reserved.</small>
<p>
This software is provided AS-IS with no warranty, either express or
implied.
This software is distributed under license and may not be copied, modified
or distributed except as expressly authorized under the terms of that
license. Refer to licensing information at http://www.artifex.com/
or contact Artifex Software, Inc., 7 Mt. Lassen Drive - Suite A-134,
San Rafael, CA 94903, U.S.A., +1(415)492-9861, for further information.
<p>
<small>Ghostscript version 9.18, 5 October 2015
<!-- [3.0 end visible trailer] ============================================= -->
</body>
</html>
|