/usr/msp430/include/msp430c412.h is in msp430mcu 20120406-2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 | /* ============================================================================ */
/* Copyright (c) 2012, Texas Instruments Incorporated */
/* All rights reserved. */
/* */
/* Redistribution and use in source and binary forms, with or without */
/* modification, are permitted provided that the following conditions */
/* are met: */
/* */
/* * Redistributions of source code must retain the above copyright */
/* notice, this list of conditions and the following disclaimer. */
/* */
/* * Redistributions in binary form must reproduce the above copyright */
/* notice, this list of conditions and the following disclaimer in the */
/* documentation and/or other materials provided with the distribution. */
/* */
/* * Neither the name of Texas Instruments Incorporated nor the names of */
/* its contributors may be used to endorse or promote products derived */
/* from this software without specific prior written permission. */
/* */
/* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" */
/* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, */
/* THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR */
/* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR */
/* CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, */
/* EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, */
/* PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; */
/* OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, */
/* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR */
/* OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, */
/* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */
/* ============================================================================ */
/********************************************************************
*
* Standard register and bit definitions for the Texas Instruments
* MSP430 microcontroller.
*
* This file supports assembler and C development for
* MSP430x41x devices.
*
* Texas Instruments, Version 2.4
*
* Rev. 1.1, Removed leading 0 to aviod interpretation as octal
* values under C
* Rev. 1.2, Corrected LPMx_EXIT to reference new intrinsic _BIC_SR_IRQ
* Changed TAIV to be read-only
* Rev. 1.3, Enclose all #define statements with parentheses
* Rev. 1.4, Removed incorrect label 'BTRESET'
* Added missing labels for FLL
* Rev. 2.1, Fixed definition of FLL_DIV0 and FLL_DIV1
* Alignment of defintions in Users Guide and of version numbers
* Rev. 2.11,Removed definition of LCDLOWR (not available at 4xx devices)
* Rev. 2.2, Removed unused def of TASSEL2
* Rev. 2.3, Removed definitions for BTRESET
* Rev. 2.4, added definitions for Interrupt Vectors xxIV
*
********************************************************************/
#ifndef __msp430x41x
#define __msp430x41x
#define __MSP430_HEADER_VERSION__ 1064
#define __MSP430_TI_HEADERS__
#ifdef __cplusplus
extern "C" {
#endif
#include <iomacros.h>
/************************************************************
* STANDARD BITS
************************************************************/
#define BIT0 (0x0001)
#define BIT1 (0x0002)
#define BIT2 (0x0004)
#define BIT3 (0x0008)
#define BIT4 (0x0010)
#define BIT5 (0x0020)
#define BIT6 (0x0040)
#define BIT7 (0x0080)
#define BIT8 (0x0100)
#define BIT9 (0x0200)
#define BITA (0x0400)
#define BITB (0x0800)
#define BITC (0x1000)
#define BITD (0x2000)
#define BITE (0x4000)
#define BITF (0x8000)
/************************************************************
* STATUS REGISTER BITS
************************************************************/
#define C (0x0001)
#define Z (0x0002)
#define N (0x0004)
#define V (0x0100)
#define GIE (0x0008)
#define CPUOFF (0x0010)
#define OSCOFF (0x0020)
#define SCG0 (0x0040)
#define SCG1 (0x0080)
/* Low Power Modes coded with Bits 4-7 in SR */
#ifndef __STDC__ /* Begin #defines for assembler */
#define LPM0 (CPUOFF)
#define LPM1 (SCG0+CPUOFF)
#define LPM2 (SCG1+CPUOFF)
#define LPM3 (SCG1+SCG0+CPUOFF)
#define LPM4 (SCG1+SCG0+OSCOFF+CPUOFF)
/* End #defines for assembler */
#else /* Begin #defines for C */
#define LPM0_bits (CPUOFF)
#define LPM1_bits (SCG0+CPUOFF)
#define LPM2_bits (SCG1+CPUOFF)
#define LPM3_bits (SCG1+SCG0+CPUOFF)
#define LPM4_bits (SCG1+SCG0+OSCOFF+CPUOFF)
#include "in430.h"
#define LPM0 _BIS_SR(LPM0_bits) /* Enter Low Power Mode 0 */
#define LPM0_EXIT _BIC_SR_IRQ(LPM0_bits) /* Exit Low Power Mode 0 */
#define LPM1 _BIS_SR(LPM1_bits) /* Enter Low Power Mode 1 */
#define LPM1_EXIT _BIC_SR_IRQ(LPM1_bits) /* Exit Low Power Mode 1 */
#define LPM2 _BIS_SR(LPM2_bits) /* Enter Low Power Mode 2 */
#define LPM2_EXIT _BIC_SR_IRQ(LPM2_bits) /* Exit Low Power Mode 2 */
#define LPM3 _BIS_SR(LPM3_bits) /* Enter Low Power Mode 3 */
#define LPM3_EXIT _BIC_SR_IRQ(LPM3_bits) /* Exit Low Power Mode 3 */
#define LPM4 _BIS_SR(LPM4_bits) /* Enter Low Power Mode 4 */
#define LPM4_EXIT _BIC_SR_IRQ(LPM4_bits) /* Exit Low Power Mode 4 */
#endif /* End #defines for C */
/************************************************************
* PERIPHERAL FILE MAP
************************************************************/
/************************************************************
* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS
************************************************************/
#define IE1_ 0x0000 /* Interrupt Enable 1 */
sfrb(IE1, IE1_);
#define WDTIE (0x01)
#define OFIE (0x02)
#define NMIIE (0x10)
#define ACCVIE (0x20)
#define IFG1_ 0x0002 /* Interrupt Flag 1 */
sfrb(IFG1, IFG1_);
#define WDTIFG (0x01)
#define OFIFG (0x02)
#define NMIIFG (0x10)
#define IE2_ 0x0001 /* Interrupt Enable 2 */
sfrb(IE2, IE2_);
#define BTIE (0x80)
#define IFG2_ 0x0003 /* Interrupt Flag 2 */
sfrb(IFG2, IFG2_);
#define BTIFG (0x80)
/************************************************************
* WATCHDOG TIMER
************************************************************/
#define __MSP430_HAS_WDT__ /* Definition to show that Module is available */
#define WDTCTL_ 0x0120 /* Watchdog Timer Control */
sfrw(WDTCTL, WDTCTL_);
/* The bit names have been prefixed with "WDT" */
#define WDTIS0 (0x0001)
#define WDTIS1 (0x0002)
#define WDTSSEL (0x0004)
#define WDTCNTCL (0x0008)
#define WDTTMSEL (0x0010)
#define WDTNMI (0x0020)
#define WDTNMIES (0x0040)
#define WDTHOLD (0x0080)
#define WDTPW (0x5A00)
/* WDT-interval times [1ms] coded with Bits 0-2 */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MDLY_32 (WDTPW+WDTTMSEL+WDTCNTCL) /* 32ms interval (default) */
#define WDT_MDLY_8 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0) /* 8ms " */
#define WDT_MDLY_0_5 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1) /* 0.5ms " */
#define WDT_MDLY_0_064 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ADLY_1000 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL) /* 1000ms " */
#define WDT_ADLY_250 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */
#define WDT_ADLY_16 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */
#define WDT_ADLY_1_9 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " */
/* Watchdog mode -> reset after expired time */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MRST_32 (WDTPW+WDTCNTCL) /* 32ms interval (default) */
#define WDT_MRST_8 (WDTPW+WDTCNTCL+WDTIS0) /* 8ms " */
#define WDT_MRST_0_5 (WDTPW+WDTCNTCL+WDTIS1) /* 0.5ms " */
#define WDT_MRST_0_064 (WDTPW+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ARST_1000 (WDTPW+WDTCNTCL+WDTSSEL) /* 1000ms " */
#define WDT_ARST_250 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */
#define WDT_ARST_16 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */
#define WDT_ARST_1_9 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " */
/* INTERRUPT CONTROL */
/* These two bits are defined in the Special Function Registers */
/* #define WDTIE 0x01 */
/* #define WDTIFG 0x01 */
/************************************************************
* DIGITAL I/O Port1/2
************************************************************/
#define __MSP430_HAS_PORT1__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT2__ /* Definition to show that Module is available */
#define P1IN_ 0x0020 /* Port 1 Input */
const_sfrb(P1IN, P1IN_);
#define P1OUT_ 0x0021 /* Port 1 Output */
sfrb(P1OUT, P1OUT_);
#define P1DIR_ 0x0022 /* Port 1 Direction */
sfrb(P1DIR, P1DIR_);
#define P1IFG_ 0x0023 /* Port 1 Interrupt Flag */
sfrb(P1IFG, P1IFG_);
#define P1IES_ 0x0024 /* Port 1 Interrupt Edge Select */
sfrb(P1IES, P1IES_);
#define P1IE_ 0x0025 /* Port 1 Interrupt Enable */
sfrb(P1IE, P1IE_);
#define P1SEL_ 0x0026 /* Port 1 Selection */
sfrb(P1SEL, P1SEL_);
#define P2IN_ 0x0028 /* Port 2 Input */
const_sfrb(P2IN, P2IN_);
#define P2OUT_ 0x0029 /* Port 2 Output */
sfrb(P2OUT, P2OUT_);
#define P2DIR_ 0x002A /* Port 2 Direction */
sfrb(P2DIR, P2DIR_);
#define P2IFG_ 0x002B /* Port 2 Interrupt Flag */
sfrb(P2IFG, P2IFG_);
#define P2IES_ 0x002C /* Port 2 Interrupt Edge Select */
sfrb(P2IES, P2IES_);
#define P2IE_ 0x002D /* Port 2 Interrupt Enable */
sfrb(P2IE, P2IE_);
#define P2SEL_ 0x002E /* Port 2 Selection */
sfrb(P2SEL, P2SEL_);
/************************************************************
* DIGITAL I/O Port3/4
************************************************************/
#define __MSP430_HAS_PORT3__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT4__ /* Definition to show that Module is available */
#define P3IN_ 0x0018 /* Port 3 Input */
const_sfrb(P3IN, P3IN_);
#define P3OUT_ 0x0019 /* Port 3 Output */
sfrb(P3OUT, P3OUT_);
#define P3DIR_ 0x001A /* Port 3 Direction */
sfrb(P3DIR, P3DIR_);
#define P3SEL_ 0x001B /* Port 3 Selection */
sfrb(P3SEL, P3SEL_);
#define P4IN_ 0x001C /* Port 4 Input */
const_sfrb(P4IN, P4IN_);
#define P4OUT_ 0x001D /* Port 4 Output */
sfrb(P4OUT, P4OUT_);
#define P4DIR_ 0x001E /* Port 4 Direction */
sfrb(P4DIR, P4DIR_);
#define P4SEL_ 0x001F /* Port 4 Selection */
sfrb(P4SEL, P4SEL_);
/************************************************************
* DIGITAL I/O Port5/6
************************************************************/
#define __MSP430_HAS_PORT5__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT6__ /* Definition to show that Module is available */
#define P5IN_ 0x0030 /* Port 5 Input */
const_sfrb(P5IN, P5IN_);
#define P5OUT_ 0x0031 /* Port 5 Output */
sfrb(P5OUT, P5OUT_);
#define P5DIR_ 0x0032 /* Port 5 Direction */
sfrb(P5DIR, P5DIR_);
#define P5SEL_ 0x0033 /* Port 5 Selection */
sfrb(P5SEL, P5SEL_);
#define P6IN_ 0x0034 /* Port 6 Input */
const_sfrb(P6IN, P6IN_);
#define P6OUT_ 0x0035 /* Port 6 Output */
sfrb(P6OUT, P6OUT_);
#define P6DIR_ 0x0036 /* Port 6 Direction */
sfrb(P6DIR, P6DIR_);
#define P6SEL_ 0x0037 /* Port 6 Selection */
sfrb(P6SEL, P6SEL_);
/************************************************************
* BASIC TIMER
************************************************************/
#define __MSP430_HAS_BT__ /* Definition to show that Module is available */
#define BTCTL_ 0x0040 /* Basic Timer Control */
sfrb(BTCTL, BTCTL_);
/* The bit names have been prefixed with "BT" */
#define BTIP0 (0x01)
#define BTIP1 (0x02)
#define BTIP2 (0x04)
#define BTFRFQ0 (0x08)
#define BTFRFQ1 (0x10)
#define BTDIV (0x20) /* fCLK2 = ACLK:256 */
#define BTHOLD (0x40) /* BT1 is held if this bit is set */
#define BTSSEL (0x80) /* fBT = fMCLK (main clock) */
#define BTCNT1_ 0x0046 /* Basic Timer Count 1 */
sfrb(BTCNT1, BTCNT1_);
#define BTCNT2_ 0x0047 /* Basic Timer Count 2 */
sfrb(BTCNT2, BTCNT2_);
/* Frequency of the BTCNT2 coded with Bit 5 and 7 in BTCTL */
#define BT_fCLK2_ACLK (0x00)
#define BT_fCLK2_ACLK_DIV256 (BTDIV)
#define BT_fCLK2_MCLK (BTSSEL)
/* Interrupt interval time fINT coded with Bits 0-2 in BTCTL */
#define BT_fCLK2_DIV2 (0x00) /* fINT = fCLK2:2 (default) */
#define BT_fCLK2_DIV4 (BTIP0) /* fINT = fCLK2:4 */
#define BT_fCLK2_DIV8 (BTIP1) /* fINT = fCLK2:8 */
#define BT_fCLK2_DIV16 (BTIP1+BTIP0) /* fINT = fCLK2:16 */
#define BT_fCLK2_DIV32 (BTIP2) /* fINT = fCLK2:32 */
#define BT_fCLK2_DIV64 (BTIP2+BTIP0) /* fINT = fCLK2:64 */
#define BT_fCLK2_DIV128 (BTIP2+BTIP1) /* fINT = fCLK2:128 */
#define BT_fCLK2_DIV256 (BTIP2+BTIP1+BTIP0) /* fINT = fCLK2:256 */
/* Frequency of LCD coded with Bits 3-4 */
#define BT_fLCD_DIV32 (0x00) /* fLCD = fACLK:32 (default) */
#define BT_fLCD_DIV64 (BTFRFQ0) /* fLCD = fACLK:64 */
#define BT_fLCD_DIV128 (BTFRFQ1) /* fLCD = fACLK:128 */
#define BT_fLCD_DIV256 (BTFRFQ1+BTFRFQ0) /* fLCD = fACLK:256 */
/* LCD frequency values with fBT=fACLK */
#define BT_fLCD_1K (0x00) /* fACLK:32 (default) */
#define BT_fLCD_512 (BTFRFQ0) /* fACLK:64 */
#define BT_fLCD_256 (BTFRFQ1) /* fACLK:128 */
#define BT_fLCD_128 (BTFRFQ1+BTFRFQ0) /* fACLK:256 */
/* LCD frequency values with fBT=fMCLK */
#define BT_fLCD_31K (BTSSEL) /* fMCLK:32 */
#define BT_fLCD_15_5K (BTSSEL+BTFRFQ0) /* fMCLK:64 */
#define BT_fLCD_7_8K (BTSSEL+BTFRFQ1+BTFRFQ0) /* fMCLK:256 */
/* with assumed vlues of fACLK=32KHz, fMCLK=1MHz */
/* fBT=fACLK is thought for longer interval times */
#define BT_ADLY_0_064 (0x00) /* 0.064ms interval (default) */
#define BT_ADLY_0_125 (BTIP0) /* 0.125ms " */
#define BT_ADLY_0_25 (BTIP1) /* 0.25ms " */
#define BT_ADLY_0_5 (BTIP1+BTIP0) /* 0.5ms " */
#define BT_ADLY_1 (BTIP2) /* 1ms " */
#define BT_ADLY_2 (BTIP2+BTIP0) /* 2ms " */
#define BT_ADLY_4 (BTIP2+BTIP1) /* 4ms " */
#define BT_ADLY_8 (BTIP2+BTIP1+BTIP0) /* 8ms " */
#define BT_ADLY_16 (BTDIV) /* 16ms " */
#define BT_ADLY_32 (BTDIV+BTIP0) /* 32ms " */
#define BT_ADLY_64 (BTDIV+BTIP1) /* 64ms " */
#define BT_ADLY_125 (BTDIV+BTIP1+BTIP0) /* 125ms " */
#define BT_ADLY_250 (BTDIV+BTIP2) /* 250ms " */
#define BT_ADLY_500 (BTDIV+BTIP2+BTIP0) /* 500ms " */
#define BT_ADLY_1000 (BTDIV+BTIP2+BTIP1) /* 1000ms " */
#define BT_ADLY_2000 (BTDIV+BTIP2+BTIP1+BTIP0) /* 2000ms " */
/* fCLK2=fMCLK (1MHz) is thought for short interval times */
/* the timing for short intervals is more precise than ACLK */
/* NOTE */
/* Be sure that the SCFQCTL-Register is set to 01Fh so that fMCLK=1MHz */
/* Too low interval time results in interrupts too frequent for the processor to handle! */
#define BT_MDLY_0_002 (BTSSEL) /* 0.002ms interval *** interval times */
#define BT_MDLY_0_004 (BTSSEL+BTIP0) /* 0.004ms " *** too short for */
#define BT_MDLY_0_008 (BTSSEL+BTIP1) /* 0.008ms " *** interrupt */
#define BT_MDLY_0_016 (BTSSEL+BTIP1+BTIP0) /* 0.016ms " *** handling */
#define BT_MDLY_0_032 (BTSSEL+BTIP2) /* 0.032ms " */
#define BT_MDLY_0_064 (BTSSEL+BTIP2+BTIP0) /* 0.064ms " */
#define BT_MDLY_0_125 (BTSSEL+BTIP2+BTIP1) /* 0.125ms " */
#define BT_MDLY_0_25 (BTSSEL+BTIP2+BTIP1+BTIP0)/* 0.25ms " */
/* Reset/Hold coded with Bits 6-7 in BT(1)CTL */
/* this is for BT */
//#define BTRESET_CNT1 (BTRESET) /* BTCNT1 is reset while BTRESET is set */
//#define BTRESET_CNT1_2 (BTRESET+BTDIV) /* BTCNT1 .AND. BTCNT2 are reset while ~ is set */
/* this is for BT1 */
#define BTHOLD_CNT1 (BTHOLD) /* BTCNT1 is held while BTHOLD is set */
#define BTHOLD_CNT1_2 (BTHOLD+BTDIV) /* BT1CNT1 .AND. BT1CNT2 are held while ~ is set */
/* INTERRUPT CONTROL BITS */
/* #define BTIE 0x80 */
/* #define BTIFG 0x80 */
/************************************************************
* SYSTEM CLOCK, FLL+ (x41x)
************************************************************/
#define __MSP430_HAS_FLLPLUS_SMALL__ /* Definition to show that Module is available */
#define SCFI0_ 0x0050 /* System Clock Frequency Integrator 0 */
sfrb(SCFI0, SCFI0_);
#define FN_2 (0x04) /* fDCOCLK = 1.4-12MHz*/
#define FN_3 (0x08) /* fDCOCLK = 2.2-17Mhz*/
#define FN_4 (0x10) /* fDCOCLK = 3.2-25Mhz*/
#define FN_8 (0x20) /* fDCOCLK = 5-40Mhz*/
#define FLLD0 (0x40) /* Loop Divider Bit : 0 */
#define FLLD1 (0x80) /* Loop Divider Bit : 1 */
#define FLLD_1 (0x00) /* Multiply Selected Loop Freq. By 1 */
#define FLLD_2 (0x40) /* Multiply Selected Loop Freq. By 2 */
#define FLLD_4 (0x80) /* Multiply Selected Loop Freq. By 4 */
#define FLLD_8 (0xC0) /* Multiply Selected Loop Freq. By 8 */
#define SCFI1_ 0x0051 /* System Clock Frequency Integrator 1 */
sfrb(SCFI1, SCFI1_);
#define SCFQCTL_ 0x0052 /* System Clock Frequency Control */
sfrb(SCFQCTL, SCFQCTL_);
/* System clock frequency values fMCLK coded with Bits 0-6 in SCFQCTL */
/* #define SCFQ_32K 0x00 fMCLK=1*fACLK only a range from */
#define SCFQ_64K (0x01) /* fMCLK=2*fACLK 1+1 to 127+1 is possible */
#define SCFQ_128K (0x03) /* fMCLK=4*fACLK */
#define SCFQ_256K (0x07) /* fMCLK=8*fACLK */
#define SCFQ_512K (0x0F) /* fMCLK=16*fACLK */
#define SCFQ_1M (0x1F) /* fMCLK=32*fACLK */
#define SCFQ_2M (0x3F) /* fMCLK=64*fACLK */
#define SCFQ_4M (0x7F) /* fMCLK=128*fACLK */
#define SCFQ_M (0x80) /* Modulation Disable */
#define FLL_CTL0_ 0x0053 /* FLL+ Control 0 */
sfrb(FLL_CTL0, FLL_CTL0_);
#define DCOF (0x01) /* DCO Fault Flag */
#define LFOF (0x02) /* Low Frequency Oscillator Fault Flag */
#define XT1OF (0x04) /* High Frequency Oscillator Fault Flag */
#define OSCCAP0 (0x10) /* XIN/XOUT Cap 0 */
#define OSCCAP1 (0x20) /* XIN/XOUT Cap 1 */
#define XTS_FLL (0x40) /* 1: Selects high-freq. oscillator */
#define DCOPLUS (0x80) /* DCO+ Enable */
#define XCAP0PF (0x00) /* XIN Cap = XOUT Cap = 0pf */
#define XCAP10PF (0x10) /* XIN Cap = XOUT Cap = 10pf */
#define XCAP14PF (0x20) /* XIN Cap = XOUT Cap = 14pf */
#define XCAP18PF (0x30) /* XIN Cap = XOUT Cap = 18pf */
#define OSCCAP_0 (0x00) /* XIN Cap = XOUT Cap = 0pf */
#define OSCCAP_1 (0x10) /* XIN Cap = XOUT Cap = 10pf */
#define OSCCAP_2 (0x20) /* XIN Cap = XOUT Cap = 14pf */
#define OSCCAP_3 (0x30) /* XIN Cap = XOUT Cap = 18pf */
#define FLL_CTL1_ 0x0054 /* FLL+ Control 1 */
sfrb(FLL_CTL1, FLL_CTL1_);
#define FLL_DIV0 (0x01) /* FLL+ Divide Px.x/ACLK 0 */
#define FLL_DIV1 (0x02) /* FLL+ Divide Px.x/ACLK 1 */
#define FLL_DIV_1 (0x00) /* FLL+ Divide Px.x/ACLK By 1 */
#define FLL_DIV_2 (0x01) /* FLL+ Divide Px.x/ACLK By 2 */
#define FLL_DIV_4 (0x02) /* FLL+ Divide Px.x/ACLK By 4 */
#define FLL_DIV_8 (0x03) /* FLL+ Divide Px.x/ACLK By 8 */
/* INTERRUPT CONTROL BITS */
/* These two bits are defined in the Special Function Registers */
/* #define OFIFG 0x02 */
/* #define OFIE 0x02 */
/************************************************************
* Brown-Out, Supply Voltage Supervision (SVS)
************************************************************/
#define __MSP430_HAS_SVS__ /* Definition to show that Module is available */
#define SVSCTL_ 0x0056 /* SVS Control */
sfrb(SVSCTL, SVSCTL_);
#define SVSFG (0x01) /* SVS Flag */
#define SVSOP (0x02) /* SVS output (read only) */
#define SVSON (0x04) /* Switches the SVS on/off */
#define PORON (0x08) /* Enable POR Generation if Low Voltage */
#define VLDON (0x10)
#define VLDOFF (0x00)
#define VLD_1_8V (0x10)
/************************************************************
* LCD
************************************************************/
#define __MSP430_HAS_LCD4__ /* Definition to show that Module is available */
#define LCDCTL_ 0x0090 /* LCD Control */
sfrb(LCDCTL, LCDCTL_);
/* the names of the mode bits are different from the spec */
#define LCDON (0x01)
//#define LCDLOWR (0x02)
#define LCDSON (0x04)
#define LCDMX0 (0x08)
#define LCDMX1 (0x10)
#define LCDP0 (0x20)
#define LCDP1 (0x40)
#define LCDP2 (0x80)
/* Display modes coded with Bits 2-4 */
#define LCDSTATIC (LCDSON)
#define LCD2MUX (LCDMX0+LCDSON)
#define LCD3MUX (LCDMX1+LCDSON)
#define LCD4MUX (LCDMX1+LCDMX0+LCDSON)
/* Group select code with Bits 5-7 Seg.lines Dig.output */
#define LCDSG0 (0x00) /* --------- Port Only (default) */
#define LCDSG0_1 (LCDP0) /* S0 - S15 see Datasheet */
#define LCDSG0_2 (LCDP1) /* S0 - S19 see Datasheet */
#define LCDSG0_3 (LCDP1+LCDP0) /* S0 - S23 see Datasheet */
#define LCDSG0_4 (LCDP2) /* S0 - S27 see Datasheet */
#define LCDSG0_5 (LCDP2+LCDP0) /* S0 - S31 see Datasheet */
#define LCDSG0_6 (LCDP2+LCDP1) /* S0 - S35 see Datasheet */
#define LCDSG0_7 (LCDP2+LCDP1+LCDP0) /* S0 - S39 see Datasheet */
/* NOTE: YOU CAN ONLY USE THE 'S' OR 'G' DECLARATIONS FOR A COMMAND */
/* MOV #LCDSG0_3+LCDOG2_7,&LCDCTL ACTUALY MEANS MOV #LCDP1,&LCDCTL! */
#define LCDOG1_7 (0x00) /* --------- Port Only (default) */
#define LCDOG2_7 (LCDP0) /* S0 - S15 see Datasheet */
#define LCDOG3_7 (LCDP1) /* S0 - S19 see Datasheet */
#define LCDOG4_7 (LCDP1+LCDP0) /* S0 - S23 see Datasheet */
#define LCDOG5_7 (LCDP2) /* S0 - S27 see Datasheet */
#define LCDOG6_7 (LCDP2+LCDP0) /* S0 - S31 see Datasheet */
#define LCDOG7 (LCDP2+LCDP1) /* S0 - S35 see Datasheet */
#define LCDOGOFF (LCDP2+LCDP1+LCDP0) /* S0 - S39 see Datasheet */
#define LCDMEM_ (0x0091) /* LCD Memory */
#ifndef __STDC__
#define LCDMEM (LCDMEM_) /* LCD Memory (for assembler) */
#else
#define LCDMEM ((volatile char*) LCDMEM_) /* LCD Memory (for C) */
#endif
#define LCDM1_ 0x0091 /* LCD Memory 1 */
sfrb(LCDM1, LCDM1_);
#define LCDM2_ 0x0092 /* LCD Memory 2 */
sfrb(LCDM2, LCDM2_);
#define LCDM3_ 0x0093 /* LCD Memory 3 */
sfrb(LCDM3, LCDM3_);
#define LCDM4_ 0x0094 /* LCD Memory 4 */
sfrb(LCDM4, LCDM4_);
#define LCDM5_ 0x0095 /* LCD Memory 5 */
sfrb(LCDM5, LCDM5_);
#define LCDM6_ 0x0096 /* LCD Memory 6 */
sfrb(LCDM6, LCDM6_);
#define LCDM7_ 0x0097 /* LCD Memory 7 */
sfrb(LCDM7, LCDM7_);
#define LCDM8_ 0x0098 /* LCD Memory 8 */
sfrb(LCDM8, LCDM8_);
#define LCDM9_ 0x0099 /* LCD Memory 9 */
sfrb(LCDM9, LCDM9_);
#define LCDM10_ 0x009A /* LCD Memory 10 */
sfrb(LCDM10, LCDM10_);
#define LCDM11_ 0x009B /* LCD Memory 11 */
sfrb(LCDM11, LCDM11_);
#define LCDM12_ 0x009C /* LCD Memory 12 */
sfrb(LCDM12, LCDM12_);
#define LCDM13_ 0x009D /* LCD Memory 13 */
sfrb(LCDM13, LCDM13_);
#define LCDM14_ 0x009E /* LCD Memory 14 */
sfrb(LCDM14, LCDM14_);
#define LCDM15_ 0x009F /* LCD Memory 15 */
sfrb(LCDM15, LCDM15_);
#define LCDM16_ 0x00A0 /* LCD Memory 16 */
sfrb(LCDM16, LCDM16_);
#define LCDM17_ 0x00A1 /* LCD Memory 17 */
sfrb(LCDM17, LCDM17_);
#define LCDM18_ 0x00A2 /* LCD Memory 18 */
sfrb(LCDM18, LCDM18_);
#define LCDM19_ 0x00A3 /* LCD Memory 19 */
sfrb(LCDM19, LCDM19_);
#define LCDM20_ 0x00A4 /* LCD Memory 20 */
sfrb(LCDM20, LCDM20_);
#define LCDMA (LCDM10) /* LCD Memory A */
#define LCDMB (LCDM11) /* LCD Memory B */
#define LCDMC (LCDM12) /* LCD Memory C */
#define LCDMD (LCDM13) /* LCD Memory D */
#define LCDME (LCDM14) /* LCD Memory E */
#define LCDMF (LCDM15) /* LCD Memory F */
/************************************************************
* Timer A3
************************************************************/
#define __MSP430_HAS_TA3__ /* Definition to show that Module is available */
#define TAIV_ 0x012E /* Timer A Interrupt Vector Word */
const_sfrw(TAIV, TAIV_);
#define TACTL_ 0x0160 /* Timer A Control */
sfrw(TACTL, TACTL_);
#define TACCTL0_ 0x0162 /* Timer A Capture/Compare Control 0 */
sfrw(TACCTL0, TACCTL0_);
#define TACCTL1_ 0x0164 /* Timer A Capture/Compare Control 1 */
sfrw(TACCTL1, TACCTL1_);
#define TACCTL2_ 0x0166 /* Timer A Capture/Compare Control 2 */
sfrw(TACCTL2, TACCTL2_);
#define TAR_ 0x0170 /* Timer A Counter Register */
sfrw(TAR, TAR_);
#define TACCR0_ 0x0172 /* Timer A Capture/Compare 0 */
sfrw(TACCR0, TACCR0_);
#define TACCR1_ 0x0174 /* Timer A Capture/Compare 1 */
sfrw(TACCR1, TACCR1_);
#define TACCR2_ 0x0176 /* Timer A Capture/Compare 2 */
sfrw(TACCR2, TACCR2_);
/* Alternate register names */
#define CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */
#define CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */
#define CCTL2 TACCTL2 /* Timer A Capture/Compare Control 2 */
#define CCR0 TACCR0 /* Timer A Capture/Compare 0 */
#define CCR1 TACCR1 /* Timer A Capture/Compare 1 */
#define CCR2 TACCR2 /* Timer A Capture/Compare 2 */
#define CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */
#define CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */
#define CCTL2_ TACCTL2_ /* Timer A Capture/Compare Control 2 */
#define CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */
#define CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */
#define CCR2_ TACCR2_ /* Timer A Capture/Compare 2 */
/* Alternate register names - 5xx style */
#define TA0IV TAIV /* Timer A Interrupt Vector Word */
#define TA0CTL TACTL /* Timer A Control */
#define TA0CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */
#define TA0CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */
#define TA0CCTL2 TACCTL2 /* Timer A Capture/Compare Control 2 */
#define TA0R TAR /* Timer A Counter Register */
#define TA0CCR0 TACCR0 /* Timer A Capture/Compare 0 */
#define TA0CCR1 TACCR1 /* Timer A Capture/Compare 1 */
#define TA0CCR2 TACCR2 /* Timer A Capture/Compare 2 */
#define TA0IV_ TAIV_ /* Timer A Interrupt Vector Word */
#define TA0CTL_ TACTL_ /* Timer A Control */
#define TA0CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */
#define TA0CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */
#define TA0CCTL2_ TACCTL2_ /* Timer A Capture/Compare Control 2 */
#define TA0R_ TAR_ /* Timer A Counter Register */
#define TA0CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */
#define TA0CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */
#define TA0CCR2_ TACCR2_ /* Timer A Capture/Compare 2 */
#define TIMER0_A1_VECTOR TIMERA1_VECTOR /* Int. Vector: Timer A CC1-2, TA */
#define TIMER0_A0_VECTOR TIMERA0_VECTOR /* Int. Vector: Timer A CC0 */
#define TASSEL1 (0x0200) /* Timer A clock source select 1 */
#define TASSEL0 (0x0100) /* Timer A clock source select 0 */
#define ID1 (0x0080) /* Timer A clock input divider 1 */
#define ID0 (0x0040) /* Timer A clock input divider 0 */
#define MC1 (0x0020) /* Timer A mode control 1 */
#define MC0 (0x0010) /* Timer A mode control 0 */
#define TACLR (0x0004) /* Timer A counter clear */
#define TAIE (0x0002) /* Timer A counter interrupt enable */
#define TAIFG (0x0001) /* Timer A counter interrupt flag */
#define MC_0 (0x0000) /* Timer A mode control: 0 - Stop */
#define MC_1 (0x0010) /* Timer A mode control: 1 - Up to CCR0 */
#define MC_2 (0x0020) /* Timer A mode control: 2 - Continous up */
#define MC_3 (0x0030) /* Timer A mode control: 3 - Up/Down */
#define ID_0 (0x0000) /* Timer A input divider: 0 - /1 */
#define ID_1 (0x0040) /* Timer A input divider: 1 - /2 */
#define ID_2 (0x0080) /* Timer A input divider: 2 - /4 */
#define ID_3 (0x00C0) /* Timer A input divider: 3 - /8 */
#define TASSEL_0 (0x0000) /* Timer A clock source select: 0 - TACLK */
#define TASSEL_1 (0x0100) /* Timer A clock source select: 1 - ACLK */
#define TASSEL_2 (0x0200) /* Timer A clock source select: 2 - SMCLK */
#define TASSEL_3 (0x0300) /* Timer A clock source select: 3 - INCLK */
#define CM1 (0x8000) /* Capture mode 1 */
#define CM0 (0x4000) /* Capture mode 0 */
#define CCIS1 (0x2000) /* Capture input select 1 */
#define CCIS0 (0x1000) /* Capture input select 0 */
#define SCS (0x0800) /* Capture sychronize */
#define SCCI (0x0400) /* Latched capture signal (read) */
#define CAP (0x0100) /* Capture mode: 1 /Compare mode : 0 */
#define OUTMOD2 (0x0080) /* Output mode 2 */
#define OUTMOD1 (0x0040) /* Output mode 1 */
#define OUTMOD0 (0x0020) /* Output mode 0 */
#define CCIE (0x0010) /* Capture/compare interrupt enable */
#define CCI (0x0008) /* Capture input signal (read) */
#define OUT (0x0004) /* PWM Output signal if output mode 0 */
#define COV (0x0002) /* Capture/compare overflow flag */
#define CCIFG (0x0001) /* Capture/compare interrupt flag */
#define OUTMOD_0 (0x0000) /* PWM output mode: 0 - output only */
#define OUTMOD_1 (0x0020) /* PWM output mode: 1 - set */
#define OUTMOD_2 (0x0040) /* PWM output mode: 2 - PWM toggle/reset */
#define OUTMOD_3 (0x0060) /* PWM output mode: 3 - PWM set/reset */
#define OUTMOD_4 (0x0080) /* PWM output mode: 4 - toggle */
#define OUTMOD_5 (0x00A0) /* PWM output mode: 5 - Reset */
#define OUTMOD_6 (0x00C0) /* PWM output mode: 6 - PWM toggle/set */
#define OUTMOD_7 (0x00E0) /* PWM output mode: 7 - PWM reset/set */
#define CCIS_0 (0x0000) /* Capture input select: 0 - CCIxA */
#define CCIS_1 (0x1000) /* Capture input select: 1 - CCIxB */
#define CCIS_2 (0x2000) /* Capture input select: 2 - GND */
#define CCIS_3 (0x3000) /* Capture input select: 3 - Vcc */
#define CM_0 (0x0000) /* Capture mode: 0 - disabled */
#define CM_1 (0x4000) /* Capture mode: 1 - pos. edge */
#define CM_2 (0x8000) /* Capture mode: 1 - neg. edge */
#define CM_3 (0xC000) /* Capture mode: 1 - both edges */
/* TA3IV Definitions */
#define TAIV_NONE (0x0000) /* No Interrupt pending */
#define TAIV_TACCR1 (0x0002) /* TACCR1_CCIFG */
#define TAIV_TACCR2 (0x0004) /* TACCR2_CCIFG */
#define TAIV_6 (0x0006) /* Reserved */
#define TAIV_8 (0x0008) /* Reserved */
#define TAIV_TAIFG (0x000A) /* TAIFG */
/*************************************************************
* Flash Memory
*************************************************************/
#define __MSP430_HAS_FLASH__ /* Definition to show that Module is available */
#define FCTL1_ 0x0128 /* FLASH Control 1 */
sfrw(FCTL1, FCTL1_);
#define FCTL2_ 0x012A /* FLASH Control 2 */
sfrw(FCTL2, FCTL2_);
#define FCTL3_ 0x012C /* FLASH Control 3 */
sfrw(FCTL3, FCTL3_);
#define FRKEY (0x9600) /* Flash key returned by read */
#define FWKEY (0xA500) /* Flash key for write */
#define FXKEY (0x3300) /* for use with XOR instruction */
#define ERASE (0x0002) /* Enable bit for Flash segment erase */
#define MERAS (0x0004) /* Enable bit for Flash mass erase */
#define WRT (0x0040) /* Enable bit for Flash write */
#define BLKWRT (0x0080) /* Enable bit for Flash segment write */
#define SEGWRT (0x0080) /* old definition */ /* Enable bit for Flash segment write */
#define FN0 (0x0001) /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */
#define FN1 (0x0002) /* 32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */
#ifndef FN2
#define FN2 (0x0004)
#endif
#ifndef FN3
#define FN3 (0x0008)
#endif
#ifndef FN4
#define FN4 (0x0010)
#endif
#define FN5 (0x0020)
#define FSSEL0 (0x0040) /* Flash clock select 0 */ /* to distinguish from USART SSELx */
#define FSSEL1 (0x0080) /* Flash clock select 1 */
#define FSSEL_0 (0x0000) /* Flash clock select: 0 - ACLK */
#define FSSEL_1 (0x0040) /* Flash clock select: 1 - MCLK */
#define FSSEL_2 (0x0080) /* Flash clock select: 2 - SMCLK */
#define FSSEL_3 (0x00C0) /* Flash clock select: 3 - SMCLK */
#define BUSY (0x0001) /* Flash busy: 1 */
#define KEYV (0x0002) /* Flash Key violation flag */
#define ACCVIFG (0x0004) /* Flash Access violation flag */
#define WAIT (0x0008) /* Wait flag for segment write */
#define LOCK (0x0010) /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX (0x0020) /* Flash Emergency Exit */
/************************************************************
* Comparator A
************************************************************/
#define __MSP430_HAS_COMPA__ /* Definition to show that Module is available */
#define CACTL1_ 0x0059 /* Comparator A Control 1 */
sfrb(CACTL1, CACTL1_);
#define CACTL2_ 0x005A /* Comparator A Control 2 */
sfrb(CACTL2, CACTL2_);
#define CAPD_ 0x005B /* Comparator A Port Disable */
sfrb(CAPD, CAPD_);
#define CAIFG (0x01) /* Comp. A Interrupt Flag */
#define CAIE (0x02) /* Comp. A Interrupt Enable */
#define CAIES (0x04) /* Comp. A Int. Edge Select: 0:rising / 1:falling */
#define CAON (0x08) /* Comp. A enable */
#define CAREF0 (0x10) /* Comp. A Internal Reference Select 0 */
#define CAREF1 (0x20) /* Comp. A Internal Reference Select 1 */
#define CARSEL (0x40) /* Comp. A Internal Reference Enable */
#define CAEX (0x80) /* Comp. A Exchange Inputs */
#define CAREF_0 (0x00) /* Comp. A Int. Ref. Select 0 : Off */
#define CAREF_1 (0x10) /* Comp. A Int. Ref. Select 1 : 0.25*Vcc */
#define CAREF_2 (0x20) /* Comp. A Int. Ref. Select 2 : 0.5*Vcc */
#define CAREF_3 (0x30) /* Comp. A Int. Ref. Select 3 : Vt*/
#define CAOUT (0x01) /* Comp. A Output */
#define CAF (0x02) /* Comp. A Enable Output Filter */
#define P2CA0 (0x04) /* Comp. A Connect External Signal to CA0 : 1 */
#define P2CA1 (0x08) /* Comp. A Connect External Signal to CA1 : 1 */
#define CACTL24 (0x10)
#define CACTL25 (0x20)
#define CACTL26 (0x40)
#define CACTL27 (0x80)
#define CAPD0 (0x01) /* Comp. A Disable Input Buffer of Port Register .0 */
#define CAPD1 (0x02) /* Comp. A Disable Input Buffer of Port Register .1 */
#define CAPD2 (0x04) /* Comp. A Disable Input Buffer of Port Register .2 */
#define CAPD3 (0x08) /* Comp. A Disable Input Buffer of Port Register .3 */
#define CAPD4 (0x10) /* Comp. A Disable Input Buffer of Port Register .4 */
#define CAPD5 (0x20) /* Comp. A Disable Input Buffer of Port Register .5 */
#define CAPD6 (0x40) /* Comp. A Disable Input Buffer of Port Register .6 */
#define CAPD7 (0x80) /* Comp. A Disable Input Buffer of Port Register .7 */
/************************************************************
* Interrupt Vectors (offset from 0xFFE0)
************************************************************/
#define BASICTIMER_VECTOR (0x0000) /* 0xFFE0 Basic Timer */
#define PORT2_VECTOR (0x0002) /* 0xFFE2 Port 2 */
#define PORT1_VECTOR (0x0008) /* 0xFFE8 Port 1 */
#define TIMERA1_VECTOR (0x000A) /* 0xFFEA Timer A CC1-2, TA */
#define TIMERA0_VECTOR (0x000C) /* 0xFFEC Timer A CC0 */
#define WDT_VECTOR (0x0014) /* 0xFFF4 Watchdog Timer */
#define COMPARATORA_VECTOR (0x0016) /* 0xFFF6 Comparator A */
#define NMI_VECTOR (0x001C) /* 0xFFFC Non-maskable */
#define RESET_VECTOR (0x001E) /* 0xFFFE Reset [Highest Priority] */
/************************************************************
* End of Modules
************************************************************/
#ifdef __cplusplus
}
#endif /* extern "C" */
#endif /* #ifndef __msp430x41x */
|