gkrellmd 2.3.6~rc1-1build1 / etc / gkrellmd.conf

This file is indexed.

/etc/gkrellmd.conf is in gkrellmd 2.3.6~rc1-1build1.

This file is owned by root:root, with mode 0o644.

The actual contents of the file can be viewed below. 

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
# Sample config file for the GKrellM server gkrellmd

# The server update frequency is independent of and should be less than
# the client update frequency.  Values may be from 1 to 10 and should be
# smaller values to reduce network traffic.
#
#update-hz 3

# Limit number of simultaneous clients allowed to connect.
#
#max-clients 2

# Specify a specific network interface to listen on for connections.
# By default gkrellmd listens on all available network interfaces.
#
#address 127.0.0.1

# Specify the port to listen on for connections.
#
#port 19150

# List of hosts allowed to connect.  If no hosts are specified in a
# gkrellmd.conf file or on the command line, all hosts will be allowed.
#
allow-host	localhost
allow-host	127.0.0.1
allow-host	::ffff:127.0.0.1
#allow-host	192.168.0.*

# Drop privileges after startup (you must start gkrellmd as root to do it).
# NOTE: Option ignored on Windows
#
user	gkrellmd
group	proc

# Create a PID file for the running gkrellmd.  Default is no PID file.
# NOTE: Option ignored on Windows
#
#pidfile /var/run/gkrellmd.pid

# Run in background and detach from the controlling terminal
# NOTE: Option ignored on Windows
#
detach

# Enable writing logging message to the system syslog file
# NOTE: On windows this enables logging to the windows event log
#
#syslog

# Time interval between checks for various monitors.  If nfs-interval
# is <= 0 then gkrellmd will not read data for nfs file system types.
#
#fs-interval 2
#nfs-interval 16

# The Internet monitor defaults to reading tcp connections once per second.
# However, for Linux SMP kernels where reading /proc/net/tcp causes high
# cpu usage, the inet-interval may be set to 1-20 seconds to slow down
# /proc/net/tcp reads.  Or set it to 0 to totally disable the Inet monitor.
# Requires at least gkrellmd version 2.1.8.
#
#inet-interval 1

# If the mbmon daemon is started before gkrellmd with this command:
#     mbmon -r -P port-number
# (the "-r" mbmon tag mode is required) then gkrellmd will monitor mbmon
# reported sensors if this is uncommented and the port-numbers match.
#
#mbmon-port port-number

# Configure gkrellm clients to disconnect from a gkrellmd server if
# there is an io-timeout seconds interval where the client receives no input
# from the server.  Use this for conditions where gkrellmd may be
# ungracefully terminated such that socket connections are not closed.
# Minimum is 2 (less than 2 for no I/O disconnecting and is the default).
# Requires at least 2.1.8 versions of both gkrellmd and gkrellm.
#
#io-timeout 5

# Configure gkrellm clients to attempt automatic reconnects to a
# gkrellmd server every reconnect-timeout seconds after a disconnected
# state is detected.  Disconnected states are created by normal gkrellmd
# shutdowns or by an expiring io-timeout.
# Minimum is 2 (less than 2 for no automatic reconnecting and is the default).
# Requires at least 2.1.8 versions of both gkrellmd and gkrellm.
#
#reconnect-timeout 5

# Server side local mailbox counts can be sent to gkrellm clients.  List here
# paths to mbox, MH mail, or Maildir style mailboxes.
# Requires at least 2.1.11 versions of both gkrellmd and gkrellm.
# NOTE: Option ignored on Windows
#
#mailbox /var/mail/bill
#mailbox ~/Mail/inbox

# List of plugins to enable.  Use "gkrellmd -plist" to view a list of all
# available plugins.  Use "gkrellmd -plog" to output a log of the plugin
# install process (note: the detach option is ignored when using -plog).
#
#plugin-enable gkrelltopd
#plugin-enable gkrellmwho2d

# Configure gkrellmd to send the connect time for a network interface
# to all clients to be displayed in the client gkrellm timer button
# monitor display.  If this is done, the client gkrellm timer button can
# still execute commands on the client, but the button will not affect the
# timer display.  If you want the client timer button to execute commands
# on the server, your timer button commands can use ssh.
# So set this if your server box has a ppp or ippp connection and you
# want to monitor its connect time.
#net-timer ppp0

# For debugging purposes, gkrellmd can print out messages on console.
# There are several debug areas which can be enabled independently by 
# summing up the following values: 
#
# system              0x1
# mail                0x10
# net                 0x20
# timer               0x40
# sensors             0x80
# sensors             0x100
# (w/o libsensors)
# inet                0x800
# battery             0x8000
#
# i.e. debug-level 0x51 enables messages for timer, mail and system
#
#debug level 0x1

APT Browse - Built by Thomas Orozco.