/etc/yate/ysnmpagent.conf is in yate-core 5.4.0-1-1ubuntu2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 | [general]
; general SNMP configuration
; local address to bind the listener to, default is 0.0.0.0 (all interfaces)
;addr=0.0.0.0
; port on which the module listens for SNMP messages. Defaults to 161.
;port=161
;thread priority for SNMP message processing. Defaults to normal.
;thread=normal
; Version string reported by SNMP, can contain Engine substitutions
; You may consider adding ${release} or ${revision}
;version=${version}
[snmp_v2]
; SNMPv2 configuration
; read only access community string. Mandatory.
ro_community=
; read write access community string. Mandatory.
rw_community=
; read create access community string.
rc_community=
[snmp_v3]
; SNMPv3 configuration
; format for generating the snmpEngineID
; values are
; 1 = IPv4 address format,
; 2 = IPv6 address format,
; 3 = MAC address format,
; 4 = TEXT format,
; 5 = OCTETS format,
; 128 = ENTERPRISE specific format
; Defaults to 4 (TEXT)
;engine_format=4
; information for generating the snmpEngineID.
; Must correspond to the format set (i.e. if engine_format=1, engine_info must be a IPv4 address)
; If the format is TEXT (4) the default is the node name
; NOTE! IPv6 address must not use the IPv6 short format. Mandatory.
; NOTE! OCTETS format must be a hexified string
engine_info=
[traps]
; SNMP traps configuration
;enable or disable all_notifications. Defaults to true.
;enable_traps=true
; list traps to disable. Must be separated by ','.
; An entire substree of traps can be disabled by ending the name of the trap with ".*"
; (e.g. disable the whole database status traps by adding database.*)
disable_traps=
; IP address to which the traps are sent. Defaults to localhost.
;remote_ip=localhost
; port for the remote IP. Defaults to 162.
;remote_port=162
;SNMP protocol version to use for sending traps (values are SNMPv2c or SNMPv3). Defaults to SNMPv2c.
;proto_version=SNMPv2c
; if SNMPv2 is used, set the community string used for the remote SNMP entity. Mandatory if SNMPv2c traps are used.
community=
; if SNMPv3 is used, specify which configured user should be used for sending traps (there must be a section named like the given value to trap_user)
; see the example bellow (section [userV3]) for configuring a SNMPv3 user
; the specified user will not allowed to interrogate this SNMP agent, it will only be used to send traps to the configured traps receiver
;trap_user=
;[userV3]
; Configure a section for a SNMPv3 user. The name of the user is the name of the section.
; To allow SNMPv3 interrogation, at least one SNMPv3 user must be configured
; authentication pass phrase. If it is not set, authentication will not be required
;auth_password=
; authentication method ( MD5 | SHA1 ) in case it is used.
;auth_protocol=MD5
; privacy pass phrase. If it is not set, encryption will not be required
;priv_password=
; privacy encryption method ( DES | AES). Default is DES.
;priv_protocol=DES
; user access level. Mandatory. Acceptable values are: readonly, readwrite, readcreate.
;access=
|